Commit ee6ff743 authored by Ulf Hansson's avatar Ulf Hansson

mmc: core: Restore parts of the polling policy when switch to HS/HS DDR

Regressions for not being able to detect an eMMC HS DDR mode card has been
reported for the sdhci-esdhc-imx driver, but potentially other sdhci
variants may suffer from the similar problem.

The commit e173f891 ("mmc: core: Update CMD13 polling policy when
switch to HS DDR mode"), is causing the problem. It seems that change moved
one step to far, regarding changing the host's timing before polling for a
busy card.

To fix this, let's move back to the behaviour when the host's timing is
updated after the polling, but before the switch status is fetched and
validated.

In cases when polling with CMD13, we keep validating the switch status at
each attempt. However, to align with the other card busy detections
mechanism, let's fetch and validate the switch status also after the host's
timing is updated.
Reported-by: default avatarClemens Gruber <clemens.gruber@pqgruber.com>
Reported-by: default avatarGary Bisson <gary.bisson@boundarydevices.com>
Fixes: e173f891 ("mmc: core: Update CMD13 polling policy when switch..")
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Dong Aisheng <aisheng.dong@nxp.com>
Cc: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: default avatarUlf Hansson <ulf.hansson@linaro.org>
Tested-by: default avatarClemens Gruber <clemens.gruber@pqgruber.com>
Tested-by: default avatarJagan Teki <jagan@amarulasolutions.com>
Reviewed-by: default avatarShawn Lin <shawn.lin@rock-chips.com>
Tested-by: default avatarHaibo Chen <haibo.chen@nxp.com>
Reviewed-by: default avatarDong Aisheng <aisheng.dong@nxp.com>
parent 01167c7b
......@@ -506,9 +506,6 @@ static int mmc_poll_for_busy(struct mmc_card *card, unsigned int timeout_ms,
}
} while (busy);
if (host->ops->card_busy && send_status)
return mmc_switch_status(card);
return 0;
}
......@@ -577,24 +574,26 @@ int __mmc_switch(struct mmc_card *card, u8 set, u8 index, u8 value,
if (!use_busy_signal)
goto out;
/* Switch to new timing before poll and check switch status. */
if (timing)
mmc_set_timing(host, timing);
/*If SPI or used HW busy detection above, then we don't need to poll. */
if (((host->caps & MMC_CAP_WAIT_WHILE_BUSY) && use_r1b_resp) ||
mmc_host_is_spi(host)) {
if (send_status)
err = mmc_switch_status(card);
mmc_host_is_spi(host))
goto out_tim;
}
/* Let's try to poll to find out when the command is completed. */
err = mmc_poll_for_busy(card, timeout_ms, send_status, retry_crc_err);
if (err)
goto out;
out_tim:
/* Switch to new timing before check switch status. */
if (timing)
mmc_set_timing(host, timing);
if (send_status) {
err = mmc_switch_status(card);
if (err && timing)
mmc_set_timing(host, old_timing);
}
out:
mmc_retune_release(host);
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment