Commit fb329633 authored by Danesh Petigara's avatar Danesh Petigara Committed by Tejun Heo

drivers: ata: wake port before DMA stop for ALPM

The AHCI driver code stops and starts port DMA engines at will
without considering the power state of the particular port. The
AHCI specification isn't very clear on how to handle this scenario,
leaving implementation open to interpretation.

Broadcom's STB SATA host controller is unable to handle port DMA
controller restarts when the port in question is in low power mode.
When a port enters partial or slumber mode, its PHY is powered down.
When a controller restart is requested, the controller's internal
state machine expects the PHY to be brought back up by software which
never happens in this case, resulting in failures.

To avoid this situation, logic is added to manually wake up the port
just before its DMA engine is stopped, if the port happens to be in
a low power state. HBA initiated power management ensures that the port
eventually returns to its configured low power state, when the link is
idle (as per the conditions listed in the spec). A new host flag is also
added to ensure this logic is only exercised for hosts with the above
limitation.

tj: Formatting changes.
Signed-off-by: default avatarDanesh Petigara <dpetigara@broadcom.com>
Reviewed-by: default avatarMarkus Mayer <mmayer@broadcom.com>
Signed-off-by: default avatarTejun Heo <tj@kernel.org>
parent 92e963f5
......@@ -250,6 +250,7 @@ enum {
AHCI_HFLAG_MULTI_MSI = 0,
AHCI_HFLAG_MULTI_MSIX = 0,
#endif
AHCI_HFLAG_WAKE_BEFORE_STOP = (1 << 22), /* wake before DMA stop */
/* ap->flags bits */
......
......@@ -317,6 +317,7 @@ static int brcm_ahci_probe(struct platform_device *pdev)
if (IS_ERR(hpriv))
return PTR_ERR(hpriv);
hpriv->plat_data = priv;
hpriv->flags = AHCI_HFLAG_WAKE_BEFORE_STOP;
brcm_sata_alpm_init(hpriv);
......
......@@ -593,8 +593,22 @@ EXPORT_SYMBOL_GPL(ahci_start_engine);
int ahci_stop_engine(struct ata_port *ap)
{
void __iomem *port_mmio = ahci_port_base(ap);
struct ahci_host_priv *hpriv = ap->host->private_data;
u32 tmp;
/*
* On some controllers, stopping a port's DMA engine while the port
* is in ALPM state (partial or slumber) results in failures on
* subsequent DMA engine starts. For those controllers, put the
* port back in active state before stopping its DMA engine.
*/
if ((hpriv->flags & AHCI_HFLAG_WAKE_BEFORE_STOP) &&
(ap->link.lpm_policy > ATA_LPM_MAX_POWER) &&
ahci_set_lpm(&ap->link, ATA_LPM_MAX_POWER, ATA_LPM_WAKE_ONLY)) {
dev_err(ap->host->dev, "Failed to wake up port before engine stop\n");
return -EIO;
}
tmp = readl(port_mmio + PORT_CMD);
/* check if the HBA is idle */
......@@ -689,6 +703,9 @@ static int ahci_set_lpm(struct ata_link *link, enum ata_lpm_policy policy,
void __iomem *port_mmio = ahci_port_base(ap);
if (policy != ATA_LPM_MAX_POWER) {
/* wakeup flag only applies to the max power policy */
hints &= ~ATA_LPM_WAKE_ONLY;
/*
* Disable interrupts on Phy Ready. This keeps us from
* getting woken up due to spurious phy ready
......@@ -704,6 +721,7 @@ static int ahci_set_lpm(struct ata_link *link, enum ata_lpm_policy policy,
u32 cmd = readl(port_mmio + PORT_CMD);
if (policy == ATA_LPM_MAX_POWER || !(hints & ATA_LPM_HIPM)) {
if (!(hints & ATA_LPM_WAKE_ONLY))
cmd &= ~(PORT_CMD_ASP | PORT_CMD_ALPE);
cmd |= PORT_CMD_ICC_ACTIVE;
......@@ -712,6 +730,9 @@ static int ahci_set_lpm(struct ata_link *link, enum ata_lpm_policy policy,
/* wait 10ms to be sure we've come out of LPM state */
ata_msleep(ap, 10);
if (hints & ATA_LPM_WAKE_ONLY)
return 0;
} else {
cmd |= PORT_CMD_ALPE;
if (policy == ATA_LPM_MIN_POWER)
......
......@@ -526,6 +526,7 @@ enum ata_lpm_policy {
enum ata_lpm_hints {
ATA_LPM_EMPTY = (1 << 0), /* port empty/probing */
ATA_LPM_HIPM = (1 << 1), /* may use HIPM */
ATA_LPM_WAKE_ONLY = (1 << 2), /* only wake up link */
};
/* forward declarations */
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment