Commit fc6bd727 authored by Jonathan Cameron's avatar Jonathan Cameron

staging:iio:lis3l02dq drop separate driver

Retire this venerable driver as the basic support is now in the
generic st-sensors accelerometer driver.

There are a few missing features in the new driver:
* Threshold events.
* Access to the calibration adjustment registers (patch shortly)

In exchange it brings a cleaner and more maintainable code base that actually
gets tested more than once every few years.  I'll actually be suprised
if anyone other than me has a board with one of these on that is running
an up to date kernel.
Signed-off-by: default avatarJonathan Cameron <jic23@kernel.org>
parent 4e68cfbf
...@@ -51,20 +51,6 @@ config ADIS16240 ...@@ -51,20 +51,6 @@ config ADIS16240
To compile this driver as a module, say M here: the module will be To compile this driver as a module, say M here: the module will be
called adis16240. called adis16240.
config LIS3L02DQ
tristate "ST Microelectronics LIS3L02DQ Accelerometer Driver"
depends on SPI
select IIO_TRIGGER if IIO_BUFFER
depends on !IIO_BUFFER || IIO_KFIFO_BUF
depends on GPIOLIB || COMPILE_TEST
help
Say Y here to build SPI support for the ST microelectronics
accelerometer. The driver supplies direct access via sysfs files
and an event interface via a character device.
To compile this driver as a module, say M here: the module will be
called lis3l02dq.
config SCA3000 config SCA3000
depends on IIO_BUFFER depends on IIO_BUFFER
depends on SPI depends on SPI
......
...@@ -14,9 +14,5 @@ obj-$(CONFIG_ADIS16209) += adis16209.o ...@@ -14,9 +14,5 @@ obj-$(CONFIG_ADIS16209) += adis16209.o
adis16240-y := adis16240_core.o adis16240-y := adis16240_core.o
obj-$(CONFIG_ADIS16240) += adis16240.o obj-$(CONFIG_ADIS16240) += adis16240.o
lis3l02dq-y := lis3l02dq_core.o
lis3l02dq-$(CONFIG_IIO_BUFFER) += lis3l02dq_ring.o
obj-$(CONFIG_LIS3L02DQ) += lis3l02dq.o
sca3000-y := sca3000_core.o sca3000_ring.o sca3000-y := sca3000_core.o sca3000_ring.o
obj-$(CONFIG_SCA3000) += sca3000.o obj-$(CONFIG_SCA3000) += sca3000.o
/*
* LISL02DQ.h -- support STMicroelectronics LISD02DQ
* 3d 2g Linear Accelerometers via SPI
*
* Copyright (c) 2007 Jonathan Cameron <jic23@kernel.org>
*
* Loosely based upon tle62x0.c
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#ifndef SPI_LIS3L02DQ_H_
#define SPI_LIS3L02DQ_H_
#define LIS3L02DQ_READ_REG(a) ((a) | 0x80)
#define LIS3L02DQ_WRITE_REG(a) a
/* Calibration parameters */
#define LIS3L02DQ_REG_OFFSET_X_ADDR 0x16
#define LIS3L02DQ_REG_OFFSET_Y_ADDR 0x17
#define LIS3L02DQ_REG_OFFSET_Z_ADDR 0x18
#define LIS3L02DQ_REG_GAIN_X_ADDR 0x19
#define LIS3L02DQ_REG_GAIN_Y_ADDR 0x1A
#define LIS3L02DQ_REG_GAIN_Z_ADDR 0x1B
/* Control Register (1 of 2) */
#define LIS3L02DQ_REG_CTRL_1_ADDR 0x20
/* Power ctrl - either bit set corresponds to on*/
#define LIS3L02DQ_REG_CTRL_1_PD_ON 0xC0
/* Decimation Factor */
#define LIS3L02DQ_DEC_MASK 0x30
#define LIS3L02DQ_REG_CTRL_1_DF_128 0x00
#define LIS3L02DQ_REG_CTRL_1_DF_64 0x10
#define LIS3L02DQ_REG_CTRL_1_DF_32 0x20
#define LIS3L02DQ_REG_CTRL_1_DF_8 (0x10 | 0x20)
/* Self Test Enable */
#define LIS3L02DQ_REG_CTRL_1_SELF_TEST_ON 0x08
/* Axes enable ctrls */
#define LIS3L02DQ_REG_CTRL_1_AXES_Z_ENABLE 0x04
#define LIS3L02DQ_REG_CTRL_1_AXES_Y_ENABLE 0x02
#define LIS3L02DQ_REG_CTRL_1_AXES_X_ENABLE 0x01
/* Control Register (2 of 2) */
#define LIS3L02DQ_REG_CTRL_2_ADDR 0x21
/* Block Data Update only after MSB and LSB read */
#define LIS3L02DQ_REG_CTRL_2_BLOCK_UPDATE 0x40
/* Set to big endian output */
#define LIS3L02DQ_REG_CTRL_2_BIG_ENDIAN 0x20
/* Reboot memory content */
#define LIS3L02DQ_REG_CTRL_2_REBOOT_MEMORY 0x10
/* Interrupt Enable - applies data ready to the RDY pad */
#define LIS3L02DQ_REG_CTRL_2_ENABLE_INTERRUPT 0x08
/* Enable Data Ready Generation - relationship with previous unclear in docs */
#define LIS3L02DQ_REG_CTRL_2_ENABLE_DATA_READY_GENERATION 0x04
/* SPI 3 wire mode */
#define LIS3L02DQ_REG_CTRL_2_THREE_WIRE_SPI_MODE 0x02
/* Data alignment, default is 12 bit right justified
* - option for 16 bit left justified
*/
#define LIS3L02DQ_REG_CTRL_2_DATA_ALIGNMENT_16_BIT_LEFT_JUSTIFIED 0x01
/* Interrupt related stuff */
#define LIS3L02DQ_REG_WAKE_UP_CFG_ADDR 0x23
/* Switch from or combination of conditions to and */
#define LIS3L02DQ_REG_WAKE_UP_CFG_BOOLEAN_AND 0x80
/* Latch interrupt request,
* if on ack must be given by reading the ack register
*/
#define LIS3L02DQ_REG_WAKE_UP_CFG_LATCH_SRC 0x40
/* Z Interrupt on High (above threshold) */
#define LIS3L02DQ_REG_WAKE_UP_CFG_INTERRUPT_Z_HIGH 0x20
/* Z Interrupt on Low */
#define LIS3L02DQ_REG_WAKE_UP_CFG_INTERRUPT_Z_LOW 0x10
/* Y Interrupt on High */
#define LIS3L02DQ_REG_WAKE_UP_CFG_INTERRUPT_Y_HIGH 0x08
/* Y Interrupt on Low */
#define LIS3L02DQ_REG_WAKE_UP_CFG_INTERRUPT_Y_LOW 0x04
/* X Interrupt on High */
#define LIS3L02DQ_REG_WAKE_UP_CFG_INTERRUPT_X_HIGH 0x02
/* X Interrupt on Low */
#define LIS3L02DQ_REG_WAKE_UP_CFG_INTERRUPT_X_LOW 0x01
/* Register that gives description of what caused interrupt
* - latched if set in CFG_ADDRES
*/
#define LIS3L02DQ_REG_WAKE_UP_SRC_ADDR 0x24
/* top bit ignored */
/* Interrupt Active */
#define LIS3L02DQ_REG_WAKE_UP_SRC_INTERRUPT_ACTIVATED 0x40
/* Interupts that have been triggered */
#define LIS3L02DQ_REG_WAKE_UP_SRC_INTERRUPT_Z_HIGH 0x20
#define LIS3L02DQ_REG_WAKE_UP_SRC_INTERRUPT_Z_LOW 0x10
#define LIS3L02DQ_REG_WAKE_UP_SRC_INTERRUPT_Y_HIGH 0x08
#define LIS3L02DQ_REG_WAKE_UP_SRC_INTERRUPT_Y_LOW 0x04
#define LIS3L02DQ_REG_WAKE_UP_SRC_INTERRUPT_X_HIGH 0x02
#define LIS3L02DQ_REG_WAKE_UP_SRC_INTERRUPT_X_LOW 0x01
#define LIS3L02DQ_REG_WAKE_UP_ACK_ADDR 0x25
/* Status register */
#define LIS3L02DQ_REG_STATUS_ADDR 0x27
/* XYZ axis data overrun - first is all overrun? */
#define LIS3L02DQ_REG_STATUS_XYZ_OVERRUN 0x80
#define LIS3L02DQ_REG_STATUS_Z_OVERRUN 0x40
#define LIS3L02DQ_REG_STATUS_Y_OVERRUN 0x20
#define LIS3L02DQ_REG_STATUS_X_OVERRUN 0x10
/* XYZ new data available - first is all 3 available? */
#define LIS3L02DQ_REG_STATUS_XYZ_NEW_DATA 0x08
#define LIS3L02DQ_REG_STATUS_Z_NEW_DATA 0x04
#define LIS3L02DQ_REG_STATUS_Y_NEW_DATA 0x02
#define LIS3L02DQ_REG_STATUS_X_NEW_DATA 0x01
/* The accelerometer readings - low and high bytes.
* Form of high byte dependent on justification set in ctrl reg
*/
#define LIS3L02DQ_REG_OUT_X_L_ADDR 0x28
#define LIS3L02DQ_REG_OUT_X_H_ADDR 0x29
#define LIS3L02DQ_REG_OUT_Y_L_ADDR 0x2A
#define LIS3L02DQ_REG_OUT_Y_H_ADDR 0x2B
#define LIS3L02DQ_REG_OUT_Z_L_ADDR 0x2C
#define LIS3L02DQ_REG_OUT_Z_H_ADDR 0x2D
/* Threshold values for all axes and both above and below thresholds
* - i.e. there is only one value
*/
#define LIS3L02DQ_REG_THS_L_ADDR 0x2E
#define LIS3L02DQ_REG_THS_H_ADDR 0x2F
#define LIS3L02DQ_DEFAULT_CTRL1 (LIS3L02DQ_REG_CTRL_1_PD_ON \
| LIS3L02DQ_REG_CTRL_1_AXES_Z_ENABLE \
| LIS3L02DQ_REG_CTRL_1_AXES_Y_ENABLE \
| LIS3L02DQ_REG_CTRL_1_AXES_X_ENABLE \
| LIS3L02DQ_REG_CTRL_1_DF_128)
#define LIS3L02DQ_DEFAULT_CTRL2 0
#define LIS3L02DQ_MAX_TX 12
#define LIS3L02DQ_MAX_RX 12
/**
* struct lis3l02dq_state - device instance specific data
* @us: actual spi_device
* @trig: data ready trigger registered with iio
* @buf_lock: mutex to protect tx and rx
* @tx: transmit buffer
* @rx: receive buffer
**/
struct lis3l02dq_state {
struct spi_device *us;
struct iio_trigger *trig;
struct mutex buf_lock;
int gpio;
bool trigger_on;
u8 tx[LIS3L02DQ_MAX_RX] ____cacheline_aligned;
u8 rx[LIS3L02DQ_MAX_RX] ____cacheline_aligned;
};
int lis3l02dq_spi_read_reg_8(struct iio_dev *indio_dev,
u8 reg_address,
u8 *val);
int lis3l02dq_spi_write_reg_8(struct iio_dev *indio_dev,
u8 reg_address,
u8 val);
int lis3l02dq_disable_all_events(struct iio_dev *indio_dev);
#ifdef CONFIG_IIO_BUFFER
/* At the moment triggers are only used for buffer
* filling. This may change!
*/
void lis3l02dq_remove_trigger(struct iio_dev *indio_dev);
int lis3l02dq_probe_trigger(struct iio_dev *indio_dev);
int lis3l02dq_configure_buffer(struct iio_dev *indio_dev);
void lis3l02dq_unconfigure_buffer(struct iio_dev *indio_dev);
irqreturn_t lis3l02dq_data_rdy_trig_poll(int irq, void *private);
#define lis3l02dq_th lis3l02dq_data_rdy_trig_poll
#else /* CONFIG_IIO_BUFFER */
#define lis3l02dq_th lis3l02dq_nobuffer
static inline void lis3l02dq_remove_trigger(struct iio_dev *indio_dev)
{
}
static inline int lis3l02dq_probe_trigger(struct iio_dev *indio_dev)
{
return 0;
}
static int lis3l02dq_configure_buffer(struct iio_dev *indio_dev)
{
return 0;
}
static inline void lis3l02dq_unconfigure_buffer(struct iio_dev *indio_dev)
{
}
#endif /* CONFIG_IIO_BUFFER */
#endif /* SPI_LIS3L02DQ_H_ */
This diff is collapsed.
This diff is collapsed.
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment