Commit fe48cb85 authored by Pratyush Anand's avatar Pratyush Anand Committed by Bjorn Helgaas

PCI: designware: Keep viewport fixed for IO transaction if num_viewport > 2

Most of the platforms have 3 or more viewports.  For such platforms, We do
not need to share viewports between IO and CFG.  Assign viewport 2 to IO
transactions in such cases.
Tested-by: default avatarDong Bo <dongbo4@huawei.com>
Signed-off-by: default avatarPratyush Anand <pratyush.anand@gmail.com>
Signed-off-by: default avatarBjorn Helgaas <bhelgaas@google.com>
Acked-by: default avatarRob Herring <robh@kernel.org>
parent 01c07673
......@@ -17,6 +17,8 @@ Required properties:
- num-lanes: number of lanes to use
Optional properties:
- num-viewport: number of view ports configured in hardware. If a platform
does not specify it, the driver assumes 2.
- num-lanes: number of lanes to use (this property should be specified unless
the link is brought already up in BIOS)
- reset-gpio: gpio pin number of power good signal
......@@ -44,4 +46,5 @@ Example configuration:
interrupts = <25>, <24>;
#interrupt-cells = <1>;
num-lanes = <1>;
num-viewport = <3>;
};
......@@ -61,6 +61,7 @@
#define PCIE_ATU_VIEWPORT 0x900
#define PCIE_ATU_REGION_INBOUND (0x1 << 31)
#define PCIE_ATU_REGION_OUTBOUND (0x0 << 31)
#define PCIE_ATU_REGION_INDEX2 (0x2 << 0)
#define PCIE_ATU_REGION_INDEX1 (0x1 << 0)
#define PCIE_ATU_REGION_INDEX0 (0x0 << 0)
#define PCIE_ATU_CR1 0x904
......@@ -616,6 +617,10 @@ int dw_pcie_host_init(struct pcie_port *pp)
if (ret)
pp->lanes = 0;
ret = of_property_read_u32(np, "num-viewport", &pp->num_viewport);
if (ret)
pp->num_viewport = 2;
if (IS_ENABLED(CONFIG_PCI_MSI)) {
if (!pp->ops->msi_host_init) {
pp->irq_domain = irq_domain_add_linear(pp->dev->of_node,
......@@ -707,6 +712,7 @@ static int dw_pcie_rd_other_conf(struct pcie_port *pp, struct pci_bus *bus,
type, cpu_addr,
busdev, cfg_size);
ret = dw_pcie_cfg_read(va_cfg_base + where, size, val);
if (pp->num_viewport <= 2)
dw_pcie_prog_outbound_atu(pp, PCIE_ATU_REGION_INDEX0,
PCIE_ATU_TYPE_IO, pp->io_base,
pp->io_bus_addr, pp->io_size);
......@@ -744,6 +750,7 @@ static int dw_pcie_wr_other_conf(struct pcie_port *pp, struct pci_bus *bus,
type, cpu_addr,
busdev, cfg_size);
ret = dw_pcie_cfg_write(va_cfg_base + where, size, val);
if (pp->num_viewport <= 2)
dw_pcie_prog_outbound_atu(pp, PCIE_ATU_REGION_INDEX0,
PCIE_ATU_TYPE_IO, pp->io_base,
pp->io_bus_addr, pp->io_size);
......@@ -882,10 +889,15 @@ void dw_pcie_setup_rc(struct pcie_port *pp)
* uses its own address translation component rather than ATU, so
* we should not program the ATU here.
*/
if (!pp->ops->rd_other_conf)
if (!pp->ops->rd_other_conf) {
dw_pcie_prog_outbound_atu(pp, PCIE_ATU_REGION_INDEX1,
PCIE_ATU_TYPE_MEM, pp->mem_base,
pp->mem_bus_addr, pp->mem_size);
if (pp->num_viewport > 2)
dw_pcie_prog_outbound_atu(pp, PCIE_ATU_REGION_INDEX2,
PCIE_ATU_TYPE_IO, pp->io_base,
pp->io_bus_addr, pp->io_size);
}
dw_pcie_wr_own_conf(pp, PCI_BASE_ADDRESS_0, 4, 0);
......
......@@ -44,6 +44,7 @@ struct pcie_port {
struct resource *busn;
int irq;
u32 lanes;
u32 num_viewport;
struct pcie_host_ops *ops;
int msi_irq;
struct irq_domain *irq_domain;
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment