Merge branch 'stmmac-add-some-fixes-for-stm32'

Christophe Roullier says:

====================
stmmac: add some fixes for stm32

For common stmmac:
	- Add support to set CSR Clock range selection in DT
For stm32mpu:
	- Glue codes to support magic packet
	- Glue codes to support all PHY config :
		PHY_MODE (MII,GMII, RMII, RGMII) and in normal,
		PHY wo crystal (25Mhz),
		PHY wo crystal (50Mhz), No 125Mhz from PHY config
For stm32mcu:
	- Add Ethernet support for stm32h7

Changes in V3:
	- Reverse for syscfg management because it is manage by these patches
	  https://lkml.org/lkml/2018/12/12/133
	  https://lkml.org/lkml/2018/12/12/134
	  https://lkml.org/lkml/2018/12/12/131
	  https://lkml.org/lkml/2018/12/12/132
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Documentation/devicetree/bindings/net/stm32-dwmac.txt

@@ -14,8 +14,7 @@ Required properties:
 - clock-names: Should be "stmmaceth" for the host clock.
 	       Should be "mac-clk-tx" for the MAC TX clock.
 	       Should be "mac-clk-rx" for the MAC RX clock.
-	       For MPU family need to add also "ethstp" for power mode clock and,
-	                                       "syscfg-clk" for SYSCFG clock.
+	       For MPU family need to add also "ethstp" for power mode clock
 - interrupt-names: Should contain a list of interrupt names corresponding to
            the interrupts in the interrupts property, if available.
 		   Should be "macirq" for the main MAC IRQ
@@ -24,9 +23,9 @@ Required properties:
 	       encompases the glue register, and the offset of the control register.
 
 Optional properties:
-- clock-names:     For MPU family "mac-clk-ck" for PHY without quartz
-- st,int-phyclk (boolean) :  valid only where PHY do not have quartz and need to be clock
-	           by RCC
+- clock-names:     For MPU family "eth-ck" for PHY without quartz
+- st,eth-clk-sel (boolean) : set this property in RGMII PHY when you want to select RCC clock instead of ETH_CLK125.
+- st,eth-ref-clk-sel (boolean) :  set this property in RMII mode when you have PHY without crystal 50MHz and want to select RCC clock instead of ETH_REF_CLK.
 
 Example:
 

arch/arm/boot/dts/stm32h743-pinctrl.dtsi

@@ -173,6 +173,21 @@ pins {
 				};
 			};
 
+			ethernet_rmii: rmii@0 {
+				pins {
+					pinmux = <STM32_PINMUX('G', 11, AF11)>,
+						 <STM32_PINMUX('G', 13, AF11)>,
+						 <STM32_PINMUX('G', 12, AF11)>,
+						 <STM32_PINMUX('C', 4, AF11)>,
+						 <STM32_PINMUX('C', 5, AF11)>,
+						 <STM32_PINMUX('A', 7, AF11)>,
+						 <STM32_PINMUX('C', 1, AF11)>,
+						 <STM32_PINMUX('A', 2, AF11)>,
+						 <STM32_PINMUX('A', 1, AF11)>;
+					slew-rate = <2>;
+				};
+			};
+
 			usart1_pins: usart1@0 {
 				pins1 {
 					pinmux = <STM32_PINMUX('B', 14, AF4)>; /* USART1_TX */

arch/arm/boot/dts/stm32h743.dtsi

@@ -511,6 +511,19 @@ adc3: adc@0 {
 				status = "disabled";
 			};
 		};
+
+		mac: ethernet@40028000 {
+			compatible = "st,stm32-dwmac", "snps,dwmac-4.10a";
+			reg = <0x40028000 0x8000>;
+			reg-names = "stmmaceth";
+			interrupts = <61>;
+			interrupt-names = "macirq";
+			clock-names = "stmmaceth", "mac-clk-tx", "mac-clk-rx";
+			clocks = <&rcc ETH1MAC_CK>, <&rcc ETH1TX_CK>, <&rcc ETH1RX_CK>;
+			st,syscon = <&syscfg 0x4>;
+			snps,pbl = <8>;
+			status = "disabled";
+		};
 	};
 };
 

arch/arm/boot/dts/stm32h743i-disco.dts

@@ -66,6 +66,23 @@ &clk_hse {
 	clock-frequency = <25000000>;
 };
 
+&mac {
+	status = "disabled";
+	pinctrl-0	= <&ethernet_rmii>;
+	pinctrl-names	= "default";
+	phy-mode	= "rmii";
+	phy-handle	= <&phy0>;
+
+	mdio0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		phy0: ethernet-phy@0 {
+			reg = <0>;
+		};
+	};
+};
+
 &usart2 {
 	pinctrl-0 = <&usart2_pins>;
 	pinctrl-names = "default";

arch/arm/boot/dts/stm32h743i-eval.dts

@@ -104,6 +104,23 @@ &rtc {
 	status = "okay";
 };
 
+&mac {
+	status = "disabled";
+	pinctrl-0	= <&ethernet_rmii>;
+	pinctrl-names	= "default";
+	phy-mode	= "rmii";
+	phy-handle	= <&phy0>;
+
+	mdio0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		phy0: ethernet-phy@0 {
+			reg = <0>;
+		};
+	};
+};
+
 &usart1 {
 	pinctrl-0 = <&usart1_pins>;
 	pinctrl-names = "default";

drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c

@@ -25,9 +25,24 @@
 
 #define SYSCFG_MCU_ETH_MASK		BIT(23)
 #define SYSCFG_MP1_ETH_MASK		GENMASK(23, 16)
+#define SYSCFG_PMCCLRR_OFFSET		0x40
 
 #define SYSCFG_PMCR_ETH_CLK_SEL		BIT(16)
 #define SYSCFG_PMCR_ETH_REF_CLK_SEL	BIT(17)
+
+/*  Ethernet PHY interface selection in register SYSCFG Configuration
+ *------------------------------------------
+ * src	 |BIT(23)| BIT(22)| BIT(21)|BIT(20)|
+ *------------------------------------------
+ * MII   |   0	 |   0	  |   0    |   1   |
+ *------------------------------------------
+ * GMII  |   0	 |   0	  |   0    |   0   |
+ *------------------------------------------
+ * RGMII |   0	 |   0	  |   1	   |  n/a  |
+ *------------------------------------------
+ * RMII  |   1	 |   0	  |   0	   |  n/a  |
+ *------------------------------------------
+ */
 #define SYSCFG_PMCR_ETH_SEL_MII		BIT(20)
 #define SYSCFG_PMCR_ETH_SEL_RGMII	BIT(21)
 #define SYSCFG_PMCR_ETH_SEL_RMII	BIT(23)
@@ -35,13 +50,53 @@
 #define SYSCFG_MCU_ETH_SEL_MII		0
 #define SYSCFG_MCU_ETH_SEL_RMII		1
 
+/* STM32MP1 register definitions
+ *
+ * Below table summarizes the clock requirement and clock sources for
+ * supported phy interface modes.
+ * __________________________________________________________________________
+ *|PHY_MODE | Normal | PHY wo crystal|   PHY wo crystal   |No 125Mhz from PHY|
+ *|         |        |      25MHz    |        50MHz       |                  |
+ * ---------------------------------------------------------------------------
+ *|  MII    |	 -   |     eth-ck    |	      n/a	  |	  n/a        |
+ *|         |        |		     |                    |		     |
+ * ---------------------------------------------------------------------------
+ *|  GMII   |	 -   |     eth-ck    |	      n/a	  |	  n/a        |
+ *|         |        |               |                    |		     |
+ * ---------------------------------------------------------------------------
+ *| RGMII   |	 -   |     eth-ck    |	      n/a	  |  eth-ck (no pin) |
+ *|         |        |               |                    |  st,eth-clk-sel  |
+ * ---------------------------------------------------------------------------
+ *| RMII    |	 -   |     eth-ck    |	    eth-ck        |	  n/a        |
+ *|         |        |		     | st,eth-ref-clk-sel |		     |
+ * ---------------------------------------------------------------------------
+ *
+ * BIT(17) : set this bit in RMII mode when you have PHY without crystal 50MHz
+ * BIT(16) : set this bit in GMII/RGMII PHY when you do not want use 125Mhz
+ * from PHY
+ *-----------------------------------------------------
+ * src	 |         BIT(17)       |       BIT(16)      |
+ *-----------------------------------------------------
+ * MII   |           n/a	 |         n/a        |
+ *-----------------------------------------------------
+ * GMII  |           n/a         |   st,eth-clk-sel   |
+ *-----------------------------------------------------
+ * RGMII |           n/a         |   st,eth-clk-sel   |
+ *-----------------------------------------------------
+ * RMII  |   st,eth-ref-clk-sel	 |         n/a        |
+ *-----------------------------------------------------
+ *
+ */
+
 struct stm32_dwmac {
 	struct clk *clk_tx;
 	struct clk *clk_rx;
 	struct clk *clk_eth_ck;
 	struct clk *clk_ethstp;
 	struct clk *syscfg_clk;
-	bool int_phyclk;	/* Clock from RCC to drive PHY */
+	int eth_clk_sel_reg;
+	int eth_ref_clk_sel_reg;
+	int irq_pwr_wakeup;
 	u32 mode_reg;		 /* MAC glue-logic mode register */
 	struct regmap *regmap;
 	u32 speed;
@@ -102,7 +157,7 @@ static int stm32mp1_clk_prepare(struct stm32_dwmac *dwmac, bool prepare)
 		if (ret)
 			return ret;
 
-		if (dwmac->int_phyclk) {
+		if (dwmac->clk_eth_ck) {
 			ret = clk_prepare_enable(dwmac->clk_eth_ck);
 			if (ret) {
 				clk_disable_unprepare(dwmac->syscfg_clk);
@@ -111,7 +166,7 @@ static int stm32mp1_clk_prepare(struct stm32_dwmac *dwmac, bool prepare)
 		}
 	} else {
 		clk_disable_unprepare(dwmac->syscfg_clk);
-		if (dwmac->int_phyclk)
+		if (dwmac->clk_eth_ck)
 			clk_disable_unprepare(dwmac->clk_eth_ck);
 	}
 	return ret;
@@ -121,7 +176,7 @@ static int stm32mp1_set_mode(struct plat_stmmacenet_data *plat_dat)
 {
 	struct stm32_dwmac *dwmac = plat_dat->bsp_priv;
 	u32 reg = dwmac->mode_reg;
-	int val;
+	int val, ret;
 
 	switch (plat_dat->interface) {
 	case PHY_INTERFACE_MODE_MII:
@@ -130,19 +185,22 @@ static int stm32mp1_set_mode(struct plat_stmmacenet_data *plat_dat)
 		break;
 	case PHY_INTERFACE_MODE_GMII:
 		val = SYSCFG_PMCR_ETH_SEL_GMII;
-		if (dwmac->int_phyclk)
+		if (dwmac->eth_clk_sel_reg)
 			val |= SYSCFG_PMCR_ETH_CLK_SEL;
 		pr_debug("SYSCFG init : PHY_INTERFACE_MODE_GMII\n");
 		break;
 	case PHY_INTERFACE_MODE_RMII:
 		val = SYSCFG_PMCR_ETH_SEL_RMII;
-		if (dwmac->int_phyclk)
+		if (dwmac->eth_ref_clk_sel_reg)
 			val |= SYSCFG_PMCR_ETH_REF_CLK_SEL;
 		pr_debug("SYSCFG init : PHY_INTERFACE_MODE_RMII\n");
 		break;
 	case PHY_INTERFACE_MODE_RGMII:
+	case PHY_INTERFACE_MODE_RGMII_ID:
+	case PHY_INTERFACE_MODE_RGMII_RXID:
+	case PHY_INTERFACE_MODE_RGMII_TXID:
 		val = SYSCFG_PMCR_ETH_SEL_RGMII;
-		if (dwmac->int_phyclk)
+		if (dwmac->eth_clk_sel_reg)
 			val |= SYSCFG_PMCR_ETH_CLK_SEL;
 		pr_debug("SYSCFG init : PHY_INTERFACE_MODE_RGMII\n");
 		break;
@@ -153,6 +211,11 @@ static int stm32mp1_set_mode(struct plat_stmmacenet_data *plat_dat)
 		return -EINVAL;
 	}
 
+	/* Need to update PMCCLRR (clear register) */
+	ret = regmap_write(dwmac->regmap, reg + SYSCFG_PMCCLRR_OFFSET,
+			   dwmac->ops->syscfg_eth_mask);
+
+	/* Update PMCSETR (set register) */
 	return regmap_update_bits(dwmac->regmap, reg,
 				 dwmac->ops->syscfg_eth_mask, val);
 }
@@ -180,7 +243,7 @@ static int stm32mcu_set_mode(struct plat_stmmacenet_data *plat_dat)
 	}
 
 	return regmap_update_bits(dwmac->regmap, reg,
-				 dwmac->ops->syscfg_eth_mask, val);
+				 dwmac->ops->syscfg_eth_mask, val << 23);
 }
 
 static void stm32_dwmac_clk_disable(struct stm32_dwmac *dwmac)
@@ -232,24 +295,29 @@ static int stm32_dwmac_parse_data(struct stm32_dwmac *dwmac,
 static int stm32mp1_parse_data(struct stm32_dwmac *dwmac,
 			       struct device *dev)
 {
+	struct platform_device *pdev = to_platform_device(dev);
 	struct device_node *np = dev->of_node;
+	int err = 0;
+
+	/* Gigabit Ethernet 125MHz clock selection. */
+	dwmac->eth_clk_sel_reg = of_property_read_bool(np, "st,eth-clk-sel");
 
-	dwmac->int_phyclk = of_property_read_bool(np, "st,int-phyclk");
+	/* Ethernet 50Mhz RMII clock selection */
+	dwmac->eth_ref_clk_sel_reg =
+		of_property_read_bool(np, "st,eth-ref-clk-sel");
 
-	/* Check if internal clk from RCC selected */
-	if (dwmac->int_phyclk) {
 	/*  Get ETH_CLK clocks */
 	dwmac->clk_eth_ck = devm_clk_get(dev, "eth-ck");
 	if (IS_ERR(dwmac->clk_eth_ck)) {
-			dev_err(dev, "No ETH CK clock provided...\n");
-			return PTR_ERR(dwmac->clk_eth_ck);
-		}
+		dev_warn(dev, "No phy clock provided...\n");
+		dwmac->clk_eth_ck = NULL;
 	}
 
 	/*  Clock used for low power mode */
 	dwmac->clk_ethstp = devm_clk_get(dev, "ethstp");
 	if (IS_ERR(dwmac->clk_ethstp)) {
-		dev_err(dev, "No ETH peripheral clock provided for CStop mode ...\n");
+		dev_err(dev,
+			"No ETH peripheral clock provided for CStop mode ...\n");
 		return PTR_ERR(dwmac->clk_ethstp);
 	}
 
@@ -260,7 +328,26 @@ static int stm32mp1_parse_data(struct stm32_dwmac *dwmac,
 		return PTR_ERR(dwmac->syscfg_clk);
 	}
 
-	return 0;
+	/* Get IRQ information early to have an ability to ask for deferred
+	 * probe if needed before we went too far with resource allocation.
+	 */
+	dwmac->irq_pwr_wakeup = platform_get_irq_byname(pdev,
+							"stm32_pwr_wakeup");
+	if (!dwmac->clk_eth_ck && dwmac->irq_pwr_wakeup >= 0) {
+		err = device_init_wakeup(&pdev->dev, true);
+		if (err) {
+			dev_err(&pdev->dev, "Failed to init wake up irq\n");
+			return err;
+		}
+		err = dev_pm_set_dedicated_wake_irq(&pdev->dev,
+						    dwmac->irq_pwr_wakeup);
+		if (err) {
+			dev_err(&pdev->dev, "Failed to set wake up irq\n");
+			device_init_wakeup(&pdev->dev, false);
+		}
+		device_set_wakeup_enable(&pdev->dev, false);
+	}
+	return err;
 }
 
 static int stm32_dwmac_probe(struct platform_device *pdev)
@@ -326,9 +413,15 @@ static int stm32_dwmac_remove(struct platform_device *pdev)
 	struct net_device *ndev = platform_get_drvdata(pdev);
 	struct stmmac_priv *priv = netdev_priv(ndev);
 	int ret = stmmac_dvr_remove(&pdev->dev);
+	struct stm32_dwmac *dwmac = priv->plat->bsp_priv;
 
 	stm32_dwmac_clk_disable(priv->plat->bsp_priv);
 
+	if (dwmac->irq_pwr_wakeup >= 0) {
+		dev_pm_clear_wake_irq(&pdev->dev);
+		device_init_wakeup(&pdev->dev, false);
+	}
+
 	return ret;
 }
 
@@ -342,7 +435,7 @@ static int stm32mp1_suspend(struct stm32_dwmac *dwmac)
 
 	clk_disable_unprepare(dwmac->clk_tx);
 	clk_disable_unprepare(dwmac->syscfg_clk);
-	if (dwmac->int_phyclk)
+	if (dwmac->clk_eth_ck)
 		clk_disable_unprepare(dwmac->clk_eth_ck);
 
 	return ret;

drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c

@@ -408,6 +408,9 @@ stmmac_probe_config_dt(struct platform_device *pdev, const char **mac)
 	/* Default to phy auto-detection */
 	plat->phy_addr = -1;
 
+	/* Get clk_csr from device tree */
+	of_property_read_u32(np, "clk_csr", &plat->clk_csr);
+
 	/* "snps,phy-addr" is not a standard property. Mark it as deprecated
 	 * and warn of its use. Remove this when phy node support is added.
 	 */