autogenerated headers for rev...

autogenerated headers for rev https://github.com/mavlink/mavlink/tree/03d69a5c0917ec7fa91966c9086bafd4c1dbb855

ASLUAV/ASLUAV.h

@@ -53,7 +53,7 @@ typedef enum MAV_CMD
    MAV_CMD_NAV_LOITER_TO_ALT=31, /* Begin loiter at the specified Latitude and Longitude.  If Lat=Lon=0, then loiter at the current position.  Don't consider the navigation command complete (don't leave loiter) until the altitude has been reached.  Additionally, if the Heading Required parameter is non-zero the  aircraft will not leave the loiter until heading toward the next waypoint. |Heading Required (0 = False)| Radius. If positive loiter clockwise, negative counter-clockwise, 0 means no change to standard loiter.| Empty| Forward moving aircraft this sets exit xtrack location: 0 for center of loiter wp, 1 for exit location| Latitude| Longitude| Altitude|  */
    MAV_CMD_DO_FOLLOW=32, /* Begin following a target |System ID (of the FOLLOW_TARGET beacon). Send 0 to disable follow-me and return to the default position hold mode.| RESERVED| RESERVED| Altitude mode: 0: Keep current altitude, 1: keep altitude difference to target, 2: go to a fixed altitude above home.| Altitude above home. (used if mode=2)| RESERVED| Time to land in which the MAV should go to the default position hold mode after a message RX timeout.|  */
    MAV_CMD_DO_FOLLOW_REPOSITION=33, /* Reposition the MAV after a follow target command has been sent |Camera q1 (where 0 is on the ray from the camera to the tracking device)| Camera q2| Camera q3| Camera q4| altitude offset from target| X offset from target| Y offset from target|  */
-   MAV_CMD_DO_ORBIT=34, /* Start orbiting on the circumference of a circle defined by the parameters. Setting any value NaN results in using defaults. |Radius of the circle. positive: Orbit clockwise. negative: Orbit counter-clockwise.| Tangential Velocity. NaN: Vehicle configuration default.| Yaw behavior of the vehicle. 0: vehicle front points to the center (default). 1: Hold last heading. 2: Leave yaw uncontrolled.| Reserved (e.g. for dynamic center beacon options)| Center point latitude (if no MAV_FRAME specified) / X coordinate according to MAV_FRAME. NaN: Use current vehicle position or current center if already orbiting.| Center point longitude (if no MAV_FRAME specified) / Y coordinate according to MAV_FRAME. NaN: Use current vehicle position or current center if already orbiting.| Center point altitude (MSL) (if no MAV_FRAME specified) / Z coordinate according to MAV_FRAME. NaN: Use current vehicle position or current center if already orbiting.|  */
+   MAV_CMD_DO_ORBIT=34, /* Start orbiting on the circumference of a circle defined by the parameters. Setting any value NaN results in using defaults. |Radius of the circle. positive: Orbit clockwise. negative: Orbit counter-clockwise.| Tangential Velocity. NaN: Vehicle configuration default.| Yaw behavior of the vehicle.| Reserved (e.g. for dynamic center beacon options)| Center point latitude (if no MAV_FRAME specified) / X coordinate according to MAV_FRAME. NaN: Use current vehicle position or current center if already orbiting.| Center point longitude (if no MAV_FRAME specified) / Y coordinate according to MAV_FRAME. NaN: Use current vehicle position or current center if already orbiting.| Center point altitude (MSL) (if no MAV_FRAME specified) / Z coordinate according to MAV_FRAME. NaN: Use current vehicle position or current center if already orbiting.|  */
    MAV_CMD_NAV_ROI=80, /* Sets the region of interest (ROI) for a sensor set or the vehicle itself. This can then be used by the vehicles control system to control the vehicle attitude and the attitude of various sensors such as cameras. |Region of interest mode.| Waypoint index/ target ID. (see MAV_ROI enum)| ROI index (allows a vehicle to manage multiple ROI's)| Empty| x the location of the fixed ROI (see MAV_FRAME)| y| z|  */
    MAV_CMD_NAV_PATHPLANNING=81, /* Control autonomous path planning on the MAV. |0: Disable local obstacle avoidance / local path planning (without resetting map), 1: Enable local path planning, 2: Enable and reset local path planning| 0: Disable full path planning (without resetting map), 1: Enable, 2: Enable and reset map/occupancy grid, 3: Enable and reset planned route, but not occupancy grid| Empty| Yaw angle at goal| Latitude/X of goal| Longitude/Y of goal| Altitude/Z of goal|  */
    MAV_CMD_NAV_SPLINE_WAYPOINT=82, /* Navigate to waypoint using a spline path. |Hold time. (ignored by fixed wing, time to stay at waypoint for rotary wing)| Empty| Empty| Empty| Latitude/X of goal| Longitude/Y of goal| Altitude/Z of goal|  */

ASLUAV/version.h

@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Fri Nov 15 2019"
+#define MAVLINK_BUILD_DATE "Mon Nov 18 2019"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
  

ardupilotmega/ardupilotmega.h

@@ -70,7 +70,7 @@ typedef enum MAV_CMD
    MAV_CMD_NAV_LOITER_TO_ALT=31, /* Begin loiter at the specified Latitude and Longitude.  If Lat=Lon=0, then loiter at the current position.  Don't consider the navigation command complete (don't leave loiter) until the altitude has been reached.  Additionally, if the Heading Required parameter is non-zero the  aircraft will not leave the loiter until heading toward the next waypoint. |Heading Required (0 = False)| Radius. If positive loiter clockwise, negative counter-clockwise, 0 means no change to standard loiter.| Empty| Forward moving aircraft this sets exit xtrack location: 0 for center of loiter wp, 1 for exit location| Latitude| Longitude| Altitude|  */
    MAV_CMD_DO_FOLLOW=32, /* Begin following a target |System ID (of the FOLLOW_TARGET beacon). Send 0 to disable follow-me and return to the default position hold mode.| RESERVED| RESERVED| Altitude mode: 0: Keep current altitude, 1: keep altitude difference to target, 2: go to a fixed altitude above home.| Altitude above home. (used if mode=2)| RESERVED| Time to land in which the MAV should go to the default position hold mode after a message RX timeout.|  */
    MAV_CMD_DO_FOLLOW_REPOSITION=33, /* Reposition the MAV after a follow target command has been sent |Camera q1 (where 0 is on the ray from the camera to the tracking device)| Camera q2| Camera q3| Camera q4| altitude offset from target| X offset from target| Y offset from target|  */
-   MAV_CMD_DO_ORBIT=34, /* Start orbiting on the circumference of a circle defined by the parameters. Setting any value NaN results in using defaults. |Radius of the circle. positive: Orbit clockwise. negative: Orbit counter-clockwise.| Tangential Velocity. NaN: Vehicle configuration default.| Yaw behavior of the vehicle. 0: vehicle front points to the center (default). 1: Hold last heading. 2: Leave yaw uncontrolled.| Reserved (e.g. for dynamic center beacon options)| Center point latitude (if no MAV_FRAME specified) / X coordinate according to MAV_FRAME. NaN: Use current vehicle position or current center if already orbiting.| Center point longitude (if no MAV_FRAME specified) / Y coordinate according to MAV_FRAME. NaN: Use current vehicle position or current center if already orbiting.| Center point altitude (MSL) (if no MAV_FRAME specified) / Z coordinate according to MAV_FRAME. NaN: Use current vehicle position or current center if already orbiting.|  */
+   MAV_CMD_DO_ORBIT=34, /* Start orbiting on the circumference of a circle defined by the parameters. Setting any value NaN results in using defaults. |Radius of the circle. positive: Orbit clockwise. negative: Orbit counter-clockwise.| Tangential Velocity. NaN: Vehicle configuration default.| Yaw behavior of the vehicle.| Reserved (e.g. for dynamic center beacon options)| Center point latitude (if no MAV_FRAME specified) / X coordinate according to MAV_FRAME. NaN: Use current vehicle position or current center if already orbiting.| Center point longitude (if no MAV_FRAME specified) / Y coordinate according to MAV_FRAME. NaN: Use current vehicle position or current center if already orbiting.| Center point altitude (MSL) (if no MAV_FRAME specified) / Z coordinate according to MAV_FRAME. NaN: Use current vehicle position or current center if already orbiting.|  */
    MAV_CMD_NAV_ROI=80, /* Sets the region of interest (ROI) for a sensor set or the vehicle itself. This can then be used by the vehicles control system to control the vehicle attitude and the attitude of various sensors such as cameras. |Region of interest mode.| Waypoint index/ target ID. (see MAV_ROI enum)| ROI index (allows a vehicle to manage multiple ROI's)| Empty| x the location of the fixed ROI (see MAV_FRAME)| y| z|  */
    MAV_CMD_NAV_PATHPLANNING=81, /* Control autonomous path planning on the MAV. |0: Disable local obstacle avoidance / local path planning (without resetting map), 1: Enable local path planning, 2: Enable and reset local path planning| 0: Disable full path planning (without resetting map), 1: Enable, 2: Enable and reset map/occupancy grid, 3: Enable and reset planned route, but not occupancy grid| Empty| Yaw angle at goal| Latitude/X of goal| Longitude/Y of goal| Altitude/Z of goal|  */
    MAV_CMD_NAV_SPLINE_WAYPOINT=82, /* Navigate to waypoint using a spline path. |Hold time. (ignored by fixed wing, time to stay at waypoint for rotary wing)| Empty| Empty| Empty| Latitude/X of goal| Longitude/Y of goal| Altitude/Z of goal|  */

ardupilotmega/version.h

@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Fri Nov 15 2019"
+#define MAVLINK_BUILD_DATE "Mon Nov 18 2019"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
  

autoquad/autoquad.h

@@ -97,7 +97,7 @@ typedef enum MAV_CMD
    MAV_CMD_NAV_LOITER_TO_ALT=31, /* Begin loiter at the specified Latitude and Longitude.  If Lat=Lon=0, then loiter at the current position.  Don't consider the navigation command complete (don't leave loiter) until the altitude has been reached.  Additionally, if the Heading Required parameter is non-zero the  aircraft will not leave the loiter until heading toward the next waypoint. |Heading Required (0 = False)| Radius. If positive loiter clockwise, negative counter-clockwise, 0 means no change to standard loiter.| Empty| Forward moving aircraft this sets exit xtrack location: 0 for center of loiter wp, 1 for exit location| Latitude| Longitude| Altitude|  */
    MAV_CMD_DO_FOLLOW=32, /* Begin following a target |System ID (of the FOLLOW_TARGET beacon). Send 0 to disable follow-me and return to the default position hold mode.| RESERVED| RESERVED| Altitude mode: 0: Keep current altitude, 1: keep altitude difference to target, 2: go to a fixed altitude above home.| Altitude above home. (used if mode=2)| RESERVED| Time to land in which the MAV should go to the default position hold mode after a message RX timeout.|  */
    MAV_CMD_DO_FOLLOW_REPOSITION=33, /* Reposition the MAV after a follow target command has been sent |Camera q1 (where 0 is on the ray from the camera to the tracking device)| Camera q2| Camera q3| Camera q4| altitude offset from target| X offset from target| Y offset from target|  */
-   MAV_CMD_DO_ORBIT=34, /* Start orbiting on the circumference of a circle defined by the parameters. Setting any value NaN results in using defaults. |Radius of the circle. positive: Orbit clockwise. negative: Orbit counter-clockwise.| Tangential Velocity. NaN: Vehicle configuration default.| Yaw behavior of the vehicle. 0: vehicle front points to the center (default). 1: Hold last heading. 2: Leave yaw uncontrolled.| Reserved (e.g. for dynamic center beacon options)| Center point latitude (if no MAV_FRAME specified) / X coordinate according to MAV_FRAME. NaN: Use current vehicle position or current center if already orbiting.| Center point longitude (if no MAV_FRAME specified) / Y coordinate according to MAV_FRAME. NaN: Use current vehicle position or current center if already orbiting.| Center point altitude (MSL) (if no MAV_FRAME specified) / Z coordinate according to MAV_FRAME. NaN: Use current vehicle position or current center if already orbiting.|  */
+   MAV_CMD_DO_ORBIT=34, /* Start orbiting on the circumference of a circle defined by the parameters. Setting any value NaN results in using defaults. |Radius of the circle. positive: Orbit clockwise. negative: Orbit counter-clockwise.| Tangential Velocity. NaN: Vehicle configuration default.| Yaw behavior of the vehicle.| Reserved (e.g. for dynamic center beacon options)| Center point latitude (if no MAV_FRAME specified) / X coordinate according to MAV_FRAME. NaN: Use current vehicle position or current center if already orbiting.| Center point longitude (if no MAV_FRAME specified) / Y coordinate according to MAV_FRAME. NaN: Use current vehicle position or current center if already orbiting.| Center point altitude (MSL) (if no MAV_FRAME specified) / Z coordinate according to MAV_FRAME. NaN: Use current vehicle position or current center if already orbiting.|  */
    MAV_CMD_NAV_ROI=80, /* Sets the region of interest (ROI) for a sensor set or the vehicle itself. This can then be used by the vehicles control system to control the vehicle attitude and the attitude of various sensors such as cameras. |Region of interest mode.| Waypoint index/ target ID. (see MAV_ROI enum)| ROI index (allows a vehicle to manage multiple ROI's)| Empty| x the location of the fixed ROI (see MAV_FRAME)| y| z|  */
    MAV_CMD_NAV_PATHPLANNING=81, /* Control autonomous path planning on the MAV. |0: Disable local obstacle avoidance / local path planning (without resetting map), 1: Enable local path planning, 2: Enable and reset local path planning| 0: Disable full path planning (without resetting map), 1: Enable, 2: Enable and reset map/occupancy grid, 3: Enable and reset planned route, but not occupancy grid| Empty| Yaw angle at goal| Latitude/X of goal| Longitude/Y of goal| Altitude/Z of goal|  */
    MAV_CMD_NAV_SPLINE_WAYPOINT=82, /* Navigate to waypoint using a spline path. |Hold time. (ignored by fixed wing, time to stay at waypoint for rotary wing)| Empty| Empty| Empty| Latitude/X of goal| Longitude/Y of goal| Altitude/Z of goal|  */

autoquad/version.h

@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Fri Nov 15 2019"
+#define MAVLINK_BUILD_DATE "Mon Nov 18 2019"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
  

common/common.h

@@ -538,6 +538,20 @@ typedef enum STORAGE_STATUS
 } STORAGE_STATUS;
 #endif
 
+/** @brief Yaw behaviour during orbit flight. */
+#ifndef HAVE_ENUM_ORBIT_YAW_BEHAVIOUR
+#define HAVE_ENUM_ORBIT_YAW_BEHAVIOUR
+typedef enum ORBIT_YAW_BEHAVIOUR
+{
+   ORBIT_YAW_BEHAVIOUR_HOLD_FRONT_TO_CIRCLE_CENTER=0, /* Vehicle front points to the center (default). | */
+   ORBIT_YAW_BEHAVIOUR_HOLD_INITIAL_HEADING=1, /* Vehicle front holds heading when message received. | */
+   ORBIT_YAW_BEHAVIOUR_UNCONTROLLED=2, /* Yaw uncontrolled. | */
+   ORBIT_YAW_BEHAVIOUR_HOLD_FRONT_TANGENT_TO_CIRCLE=3, /* Vehicle front follows flight path (tangential to circle). | */
+   ORBIT_YAW_BEHAVIOUR_RC_CONTROLLED=4, /* Yaw controlled by RC input. | */
+   ORBIT_YAW_BEHAVIOUR_ENUM_END=5, /*  | */
+} ORBIT_YAW_BEHAVIOUR;
+#endif
+
 /** @brief Commands to be executed by the MAV. They can be executed on user request, or as part of a mission script. If the action is used in a mission, the parameter mapping to the waypoint/mission message is as follows: Param 1, Param 2, Param 3, Param 4, X: Param 5, Y:Param 6, Z:Param 7. This command list is similar what ARINC 424 is for commercial aircraft: A data format how to interpret waypoint/mission data. See https://mavlink.io/en/guide/xml_schema.html#MAV_CMD for information about the structure of the MAV_CMD entries */
 #ifndef HAVE_ENUM_MAV_CMD
 #define HAVE_ENUM_MAV_CMD
@@ -557,7 +571,7 @@ typedef enum MAV_CMD
    MAV_CMD_NAV_LOITER_TO_ALT=31, /* Begin loiter at the specified Latitude and Longitude.  If Lat=Lon=0, then loiter at the current position.  Don't consider the navigation command complete (don't leave loiter) until the altitude has been reached.  Additionally, if the Heading Required parameter is non-zero the  aircraft will not leave the loiter until heading toward the next waypoint. |Heading Required (0 = False)| Radius. If positive loiter clockwise, negative counter-clockwise, 0 means no change to standard loiter.| Empty| Forward moving aircraft this sets exit xtrack location: 0 for center of loiter wp, 1 for exit location| Latitude| Longitude| Altitude|  */
    MAV_CMD_DO_FOLLOW=32, /* Begin following a target |System ID (of the FOLLOW_TARGET beacon). Send 0 to disable follow-me and return to the default position hold mode.| RESERVED| RESERVED| Altitude mode: 0: Keep current altitude, 1: keep altitude difference to target, 2: go to a fixed altitude above home.| Altitude above home. (used if mode=2)| RESERVED| Time to land in which the MAV should go to the default position hold mode after a message RX timeout.|  */
    MAV_CMD_DO_FOLLOW_REPOSITION=33, /* Reposition the MAV after a follow target command has been sent |Camera q1 (where 0 is on the ray from the camera to the tracking device)| Camera q2| Camera q3| Camera q4| altitude offset from target| X offset from target| Y offset from target|  */
-   MAV_CMD_DO_ORBIT=34, /* Start orbiting on the circumference of a circle defined by the parameters. Setting any value NaN results in using defaults. |Radius of the circle. positive: Orbit clockwise. negative: Orbit counter-clockwise.| Tangential Velocity. NaN: Vehicle configuration default.| Yaw behavior of the vehicle. 0: vehicle front points to the center (default). 1: Hold last heading. 2: Leave yaw uncontrolled.| Reserved (e.g. for dynamic center beacon options)| Center point latitude (if no MAV_FRAME specified) / X coordinate according to MAV_FRAME. NaN: Use current vehicle position or current center if already orbiting.| Center point longitude (if no MAV_FRAME specified) / Y coordinate according to MAV_FRAME. NaN: Use current vehicle position or current center if already orbiting.| Center point altitude (MSL) (if no MAV_FRAME specified) / Z coordinate according to MAV_FRAME. NaN: Use current vehicle position or current center if already orbiting.|  */
+   MAV_CMD_DO_ORBIT=34, /* Start orbiting on the circumference of a circle defined by the parameters. Setting any value NaN results in using defaults. |Radius of the circle. positive: Orbit clockwise. negative: Orbit counter-clockwise.| Tangential Velocity. NaN: Vehicle configuration default.| Yaw behavior of the vehicle.| Reserved (e.g. for dynamic center beacon options)| Center point latitude (if no MAV_FRAME specified) / X coordinate according to MAV_FRAME. NaN: Use current vehicle position or current center if already orbiting.| Center point longitude (if no MAV_FRAME specified) / Y coordinate according to MAV_FRAME. NaN: Use current vehicle position or current center if already orbiting.| Center point altitude (MSL) (if no MAV_FRAME specified) / Z coordinate according to MAV_FRAME. NaN: Use current vehicle position or current center if already orbiting.|  */
    MAV_CMD_NAV_ROI=80, /* Sets the region of interest (ROI) for a sensor set or the vehicle itself. This can then be used by the vehicles control system to control the vehicle attitude and the attitude of various sensors such as cameras. |Region of interest mode.| Waypoint index/ target ID. (see MAV_ROI enum)| ROI index (allows a vehicle to manage multiple ROI's)| Empty| x the location of the fixed ROI (see MAV_FRAME)| y| z|  */
    MAV_CMD_NAV_PATHPLANNING=81, /* Control autonomous path planning on the MAV. |0: Disable local obstacle avoidance / local path planning (without resetting map), 1: Enable local path planning, 2: Enable and reset local path planning| 0: Disable full path planning (without resetting map), 1: Enable, 2: Enable and reset map/occupancy grid, 3: Enable and reset planned route, but not occupancy grid| Empty| Yaw angle at goal| Latitude/X of goal| Longitude/Y of goal| Altitude/Z of goal|  */
    MAV_CMD_NAV_SPLINE_WAYPOINT=82, /* Navigate to waypoint using a spline path. |Hold time. (ignored by fixed wing, time to stay at waypoint for rotary wing)| Empty| Empty| Empty| Latitude/X of goal| Longitude/Y of goal| Altitude/Z of goal|  */

common/version.h

@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Fri Nov 15 2019"
+#define MAVLINK_BUILD_DATE "Mon Nov 18 2019"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
  

icarous/version.h

@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Fri Nov 15 2019"
+#define MAVLINK_BUILD_DATE "Mon Nov 18 2019"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
  

matrixpilot/matrixpilot.h

@@ -70,7 +70,7 @@ typedef enum MAV_CMD
    MAV_CMD_NAV_LOITER_TO_ALT=31, /* Begin loiter at the specified Latitude and Longitude.  If Lat=Lon=0, then loiter at the current position.  Don't consider the navigation command complete (don't leave loiter) until the altitude has been reached.  Additionally, if the Heading Required parameter is non-zero the  aircraft will not leave the loiter until heading toward the next waypoint. |Heading Required (0 = False)| Radius. If positive loiter clockwise, negative counter-clockwise, 0 means no change to standard loiter.| Empty| Forward moving aircraft this sets exit xtrack location: 0 for center of loiter wp, 1 for exit location| Latitude| Longitude| Altitude|  */
    MAV_CMD_DO_FOLLOW=32, /* Begin following a target |System ID (of the FOLLOW_TARGET beacon). Send 0 to disable follow-me and return to the default position hold mode.| RESERVED| RESERVED| Altitude mode: 0: Keep current altitude, 1: keep altitude difference to target, 2: go to a fixed altitude above home.| Altitude above home. (used if mode=2)| RESERVED| Time to land in which the MAV should go to the default position hold mode after a message RX timeout.|  */
    MAV_CMD_DO_FOLLOW_REPOSITION=33, /* Reposition the MAV after a follow target command has been sent |Camera q1 (where 0 is on the ray from the camera to the tracking device)| Camera q2| Camera q3| Camera q4| altitude offset from target| X offset from target| Y offset from target|  */
-   MAV_CMD_DO_ORBIT=34, /* Start orbiting on the circumference of a circle defined by the parameters. Setting any value NaN results in using defaults. |Radius of the circle. positive: Orbit clockwise. negative: Orbit counter-clockwise.| Tangential Velocity. NaN: Vehicle configuration default.| Yaw behavior of the vehicle. 0: vehicle front points to the center (default). 1: Hold last heading. 2: Leave yaw uncontrolled.| Reserved (e.g. for dynamic center beacon options)| Center point latitude (if no MAV_FRAME specified) / X coordinate according to MAV_FRAME. NaN: Use current vehicle position or current center if already orbiting.| Center point longitude (if no MAV_FRAME specified) / Y coordinate according to MAV_FRAME. NaN: Use current vehicle position or current center if already orbiting.| Center point altitude (MSL) (if no MAV_FRAME specified) / Z coordinate according to MAV_FRAME. NaN: Use current vehicle position or current center if already orbiting.|  */
+   MAV_CMD_DO_ORBIT=34, /* Start orbiting on the circumference of a circle defined by the parameters. Setting any value NaN results in using defaults. |Radius of the circle. positive: Orbit clockwise. negative: Orbit counter-clockwise.| Tangential Velocity. NaN: Vehicle configuration default.| Yaw behavior of the vehicle.| Reserved (e.g. for dynamic center beacon options)| Center point latitude (if no MAV_FRAME specified) / X coordinate according to MAV_FRAME. NaN: Use current vehicle position or current center if already orbiting.| Center point longitude (if no MAV_FRAME specified) / Y coordinate according to MAV_FRAME. NaN: Use current vehicle position or current center if already orbiting.| Center point altitude (MSL) (if no MAV_FRAME specified) / Z coordinate according to MAV_FRAME. NaN: Use current vehicle position or current center if already orbiting.|  */
    MAV_CMD_NAV_ROI=80, /* Sets the region of interest (ROI) for a sensor set or the vehicle itself. This can then be used by the vehicles control system to control the vehicle attitude and the attitude of various sensors such as cameras. |Region of interest mode.| Waypoint index/ target ID. (see MAV_ROI enum)| ROI index (allows a vehicle to manage multiple ROI's)| Empty| x the location of the fixed ROI (see MAV_FRAME)| y| z|  */
    MAV_CMD_NAV_PATHPLANNING=81, /* Control autonomous path planning on the MAV. |0: Disable local obstacle avoidance / local path planning (without resetting map), 1: Enable local path planning, 2: Enable and reset local path planning| 0: Disable full path planning (without resetting map), 1: Enable, 2: Enable and reset map/occupancy grid, 3: Enable and reset planned route, but not occupancy grid| Empty| Yaw angle at goal| Latitude/X of goal| Longitude/Y of goal| Altitude/Z of goal|  */
    MAV_CMD_NAV_SPLINE_WAYPOINT=82, /* Navigate to waypoint using a spline path. |Hold time. (ignored by fixed wing, time to stay at waypoint for rotary wing)| Empty| Empty| Empty| Latitude/X of goal| Longitude/Y of goal| Altitude/Z of goal|  */

matrixpilot/version.h

@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Fri Nov 15 2019"
+#define MAVLINK_BUILD_DATE "Mon Nov 18 2019"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
  

message_definitions/common.xml

@@ -1041,6 +1041,24 @@
         <description>Camera does not supply storage status information. Capacity information in STORAGE_INFORMATION fields will be ignored.</description>
       </entry>
     </enum>
+    <enum name="ORBIT_YAW_BEHAVIOUR">
+      <description>Yaw behaviour during orbit flight.</description>
+      <entry value="0" name="ORBIT_YAW_BEHAVIOUR_HOLD_FRONT_TO_CIRCLE_CENTER">
+        <description>Vehicle front points to the center (default).</description>
+      </entry>
+      <entry value="1" name="ORBIT_YAW_BEHAVIOUR_HOLD_INITIAL_HEADING">
+        <description>Vehicle front holds heading when message received.</description>
+      </entry>
+      <entry value="2" name="ORBIT_YAW_BEHAVIOUR_UNCONTROLLED">
+        <description>Yaw uncontrolled.</description>
+      </entry>
+      <entry value="3" name="ORBIT_YAW_BEHAVIOUR_HOLD_FRONT_TANGENT_TO_CIRCLE">
+        <description>Vehicle front follows flight path (tangential to circle).</description>
+      </entry>
+      <entry value="4" name="ORBIT_YAW_BEHAVIOUR_RC_CONTROLLED">
+        <description>Yaw controlled by RC input.</description>
+      </entry>
+    </enum>
     <!-- The MAV_CMD enum entries describe either: -->
     <!--  * the data payload of mission items (as used in the MISSION_ITEM and MISSION_ITEM_INT messages) -->
     <!--  * the data payload of mavlink commands (as used in the COMMAND_INT and COMMAND_LONG messages) -->
@@ -1193,7 +1211,7 @@
         <description>Start orbiting on the circumference of a circle defined by the parameters. Setting any value NaN results in using defaults.</description>
         <param index="1" label="Radius" units="m">Radius of the circle. positive: Orbit clockwise. negative: Orbit counter-clockwise.</param>
         <param index="2" label="Velocity" units="m/s">Tangential Velocity. NaN: Vehicle configuration default.</param>
-        <param index="3" label="Yaw Behavior" minValue="0" maxValue="2" increment="1">Yaw behavior of the vehicle. 0: vehicle front points to the center (default). 1: Hold last heading. 2: Leave yaw uncontrolled.</param>
+        <param index="3" label="Yaw Behavior" enum="ORBIT_YAW_BEHAVIOUR">Yaw behavior of the vehicle.</param>
         <param index="4">Reserved (e.g. for dynamic center beacon options)</param>
         <param index="5">Center point latitude (if no MAV_FRAME specified) / X coordinate according to MAV_FRAME. NaN: Use current vehicle position or current center if already orbiting.</param>
         <param index="6">Center point longitude (if no MAV_FRAME specified) / Y coordinate according to MAV_FRAME. NaN: Use current vehicle position or current center if already orbiting.</param>

minimal/version.h

@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Fri Nov 15 2019"
+#define MAVLINK_BUILD_DATE "Mon Nov 18 2019"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 22
  

slugs/slugs.h

@@ -53,7 +53,7 @@ typedef enum MAV_CMD
    MAV_CMD_NAV_LOITER_TO_ALT=31, /* Begin loiter at the specified Latitude and Longitude.  If Lat=Lon=0, then loiter at the current position.  Don't consider the navigation command complete (don't leave loiter) until the altitude has been reached.  Additionally, if the Heading Required parameter is non-zero the  aircraft will not leave the loiter until heading toward the next waypoint. |Heading Required (0 = False)| Radius. If positive loiter clockwise, negative counter-clockwise, 0 means no change to standard loiter.| Empty| Forward moving aircraft this sets exit xtrack location: 0 for center of loiter wp, 1 for exit location| Latitude| Longitude| Altitude|  */
    MAV_CMD_DO_FOLLOW=32, /* Begin following a target |System ID (of the FOLLOW_TARGET beacon). Send 0 to disable follow-me and return to the default position hold mode.| RESERVED| RESERVED| Altitude mode: 0: Keep current altitude, 1: keep altitude difference to target, 2: go to a fixed altitude above home.| Altitude above home. (used if mode=2)| RESERVED| Time to land in which the MAV should go to the default position hold mode after a message RX timeout.|  */
    MAV_CMD_DO_FOLLOW_REPOSITION=33, /* Reposition the MAV after a follow target command has been sent |Camera q1 (where 0 is on the ray from the camera to the tracking device)| Camera q2| Camera q3| Camera q4| altitude offset from target| X offset from target| Y offset from target|  */
-   MAV_CMD_DO_ORBIT=34, /* Start orbiting on the circumference of a circle defined by the parameters. Setting any value NaN results in using defaults. |Radius of the circle. positive: Orbit clockwise. negative: Orbit counter-clockwise.| Tangential Velocity. NaN: Vehicle configuration default.| Yaw behavior of the vehicle. 0: vehicle front points to the center (default). 1: Hold last heading. 2: Leave yaw uncontrolled.| Reserved (e.g. for dynamic center beacon options)| Center point latitude (if no MAV_FRAME specified) / X coordinate according to MAV_FRAME. NaN: Use current vehicle position or current center if already orbiting.| Center point longitude (if no MAV_FRAME specified) / Y coordinate according to MAV_FRAME. NaN: Use current vehicle position or current center if already orbiting.| Center point altitude (MSL) (if no MAV_FRAME specified) / Z coordinate according to MAV_FRAME. NaN: Use current vehicle position or current center if already orbiting.|  */
+   MAV_CMD_DO_ORBIT=34, /* Start orbiting on the circumference of a circle defined by the parameters. Setting any value NaN results in using defaults. |Radius of the circle. positive: Orbit clockwise. negative: Orbit counter-clockwise.| Tangential Velocity. NaN: Vehicle configuration default.| Yaw behavior of the vehicle.| Reserved (e.g. for dynamic center beacon options)| Center point latitude (if no MAV_FRAME specified) / X coordinate according to MAV_FRAME. NaN: Use current vehicle position or current center if already orbiting.| Center point longitude (if no MAV_FRAME specified) / Y coordinate according to MAV_FRAME. NaN: Use current vehicle position or current center if already orbiting.| Center point altitude (MSL) (if no MAV_FRAME specified) / Z coordinate according to MAV_FRAME. NaN: Use current vehicle position or current center if already orbiting.|  */
    MAV_CMD_NAV_ROI=80, /* Sets the region of interest (ROI) for a sensor set or the vehicle itself. This can then be used by the vehicles control system to control the vehicle attitude and the attitude of various sensors such as cameras. |Region of interest mode.| Waypoint index/ target ID. (see MAV_ROI enum)| ROI index (allows a vehicle to manage multiple ROI's)| Empty| x the location of the fixed ROI (see MAV_FRAME)| y| z|  */
    MAV_CMD_NAV_PATHPLANNING=81, /* Control autonomous path planning on the MAV. |0: Disable local obstacle avoidance / local path planning (without resetting map), 1: Enable local path planning, 2: Enable and reset local path planning| 0: Disable full path planning (without resetting map), 1: Enable, 2: Enable and reset map/occupancy grid, 3: Enable and reset planned route, but not occupancy grid| Empty| Yaw angle at goal| Latitude/X of goal| Longitude/Y of goal| Altitude/Z of goal|  */
    MAV_CMD_NAV_SPLINE_WAYPOINT=82, /* Navigate to waypoint using a spline path. |Hold time. (ignored by fixed wing, time to stay at waypoint for rotary wing)| Empty| Empty| Empty| Latitude/X of goal| Longitude/Y of goal| Altitude/Z of goal|  */

slugs/version.h

@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Fri Nov 15 2019"
+#define MAVLINK_BUILD_DATE "Mon Nov 18 2019"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
  

standard/version.h

@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Fri Nov 15 2019"
+#define MAVLINK_BUILD_DATE "Mon Nov 18 2019"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
  

test/version.h

@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Fri Nov 15 2019"
+#define MAVLINK_BUILD_DATE "Mon Nov 18 2019"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 179
  

uAvionix/version.h

@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Fri Nov 15 2019"
+#define MAVLINK_BUILD_DATE "Mon Nov 18 2019"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255