autogenerated headers for rev...

autogenerated headers for rev https://github.com/mavlink/mavlink/tree/ae71666d39bac01cf41abeee5d454caeb9c8677a

ASLUAV/ASLUAV.h

@@ -113,7 +113,7 @@ typedef enum MAV_CMD
    MAV_CMD_PREFLIGHT_UAVCAN=243, /* Trigger UAVCAN config. This command will be only accepted if in pre-flight mode. |1: Trigger actuator ID assignment and direction mapping.| Reserved| Reserved| Reserved| Reserved| Reserved| Reserved|  */
    MAV_CMD_PREFLIGHT_STORAGE=245, /* Request storage of different parameter values and logs. This command will be only accepted if in pre-flight mode. |Parameter storage: 0: READ FROM FLASH/EEPROM, 1: WRITE CURRENT TO FLASH/EEPROM, 2: Reset to defaults| Mission storage: 0: READ FROM FLASH/EEPROM, 1: WRITE CURRENT TO FLASH/EEPROM, 2: Reset to defaults| Onboard logging: 0: Ignore, 1: Start default rate logging, -1: Stop logging, > 1: logging rate (e.g. set to 1000 for 1000 Hz logging)| Reserved| Empty| Empty| Empty|  */
    MAV_CMD_PREFLIGHT_REBOOT_SHUTDOWN=246, /* Request the reboot or shutdown of system components. |0: Do nothing for autopilot, 1: Reboot autopilot, 2: Shutdown autopilot, 3: Reboot autopilot and keep it in the bootloader until upgraded.| 0: Do nothing for onboard computer, 1: Reboot onboard computer, 2: Shutdown onboard computer, 3: Reboot onboard computer and keep it in the bootloader until upgraded.| WIP: 0: Do nothing for camera, 1: Reboot onboard camera, 2: Shutdown onboard camera, 3: Reboot onboard camera and keep it in the bootloader until upgraded| WIP: 0: Do nothing for mount (e.g. gimbal), 1: Reboot mount, 2: Shutdown mount, 3: Reboot mount and keep it in the bootloader until upgraded| Reserved (set to 0)| Reserved (set to 0)| WIP: ID (e.g. camera ID -1 for all IDs)|  */
-   MAV_CMD_DO_UPGRADE=247, /* Request a target system to start, cancel, or restart upgrade of one (or all) of its components. For example, the command might be sent to a companion computer to cause it to upgrade a connected flight controller. The system doing the upgrade will report progress using the normal command protocol sequence (COMMAND_ACK regularly sent with result=MAV_RESULT_IN_PROGRESS, followed by a final result of MAV_RESULT_ACCEPTED or MAV_RESULT_FAILED). The operation can be cancelled, in which case the updating system would send COMMAND_ACK with MAV_RESULT_ACCEPTED. The operation can be restarted, in which case the updating system should respond with progress updates (as though it had a new message). |Component id of the component to be upgraded. If set to 0, all components should be upgraded.| 0: Start component upgrade, 1: Cancel component upgrade, 2: Restart component upgrade.| 0: Do not reboot component after the action is executed, 1: Reboot component after the action is executed.| Reserved| Reserved| Reserved| WIP: upgrade progress report rate (can be used for more granular control).|  */
+   MAV_CMD_DO_UPGRADE=247, /* Request a target system to start an upgrade of one (or all) of its components. For example, the command might be sent to a companion computer to cause it to upgrade a connected flight controller. The system doing the upgrade will report progress using the normal command protocol sequence for a long running operation. Command protocol information: https://mavlink.io/en/services/command.html. |Component id of the component to be upgraded. If set to 0, all components should be upgraded.| 0: Do not reboot component after the action is executed, 1: Reboot component after the action is executed.| Reserved| Reserved| Reserved| Reserved| WIP: upgrade progress report rate (can be used for more granular control).|  */
    MAV_CMD_OVERRIDE_GOTO=252, /* Override current mission with command to pause mission, pause mission and move to position, continue/resume mission. When param 1 indicates that the mission is paused (MAV_GOTO_DO_HOLD), param 2 defines whether it holds in place or moves to another position. |MAV_GOTO_DO_HOLD: pause mission and either hold or move to specified position (depending on param2), MAV_GOTO_DO_CONTINUE: resume mission.| MAV_GOTO_HOLD_AT_CURRENT_POSITION: hold at current position, MAV_GOTO_HOLD_AT_SPECIFIED_POSITION: hold at specified position.| Coordinate frame of hold point.| Desired yaw angle.| Latitude/X position.| Longitude/Y position.| Altitude/Z position.|  */
    MAV_CMD_MISSION_START=300, /* start running a mission |first_item: the first mission item to run| last_item:  the last mission item to run (after this item is run, the mission ends)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
    MAV_CMD_COMPONENT_ARM_DISARM=400, /* Arms / Disarms a component |0: disarm, 1: arm| 0: arm-disarm unless prevented by safety checks (i.e. when landed), 21196: force arming/disarming (e.g. allow arming to override preflight checks and disarming in flight)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */

ASLUAV/version.h

@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Thu Jun 25 2020"
+#define MAVLINK_BUILD_DATE "Sat Jun 27 2020"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
  

ardupilotmega/ardupilotmega.h

@@ -134,7 +134,7 @@ typedef enum MAV_CMD
    MAV_CMD_PREFLIGHT_UAVCAN=243, /* Trigger UAVCAN config. This command will be only accepted if in pre-flight mode. |1: Trigger actuator ID assignment and direction mapping.| Reserved| Reserved| Reserved| Reserved| Reserved| Reserved|  */
    MAV_CMD_PREFLIGHT_STORAGE=245, /* Request storage of different parameter values and logs. This command will be only accepted if in pre-flight mode. |Parameter storage: 0: READ FROM FLASH/EEPROM, 1: WRITE CURRENT TO FLASH/EEPROM, 2: Reset to defaults| Mission storage: 0: READ FROM FLASH/EEPROM, 1: WRITE CURRENT TO FLASH/EEPROM, 2: Reset to defaults| Onboard logging: 0: Ignore, 1: Start default rate logging, -1: Stop logging, > 1: logging rate (e.g. set to 1000 for 1000 Hz logging)| Reserved| Empty| Empty| Empty|  */
    MAV_CMD_PREFLIGHT_REBOOT_SHUTDOWN=246, /* Request the reboot or shutdown of system components. |0: Do nothing for autopilot, 1: Reboot autopilot, 2: Shutdown autopilot, 3: Reboot autopilot and keep it in the bootloader until upgraded.| 0: Do nothing for onboard computer, 1: Reboot onboard computer, 2: Shutdown onboard computer, 3: Reboot onboard computer and keep it in the bootloader until upgraded.| WIP: 0: Do nothing for camera, 1: Reboot onboard camera, 2: Shutdown onboard camera, 3: Reboot onboard camera and keep it in the bootloader until upgraded| WIP: 0: Do nothing for mount (e.g. gimbal), 1: Reboot mount, 2: Shutdown mount, 3: Reboot mount and keep it in the bootloader until upgraded| Reserved (set to 0)| Reserved (set to 0)| WIP: ID (e.g. camera ID -1 for all IDs)|  */
-   MAV_CMD_DO_UPGRADE=247, /* Request a target system to start, cancel, or restart upgrade of one (or all) of its components. For example, the command might be sent to a companion computer to cause it to upgrade a connected flight controller. The system doing the upgrade will report progress using the normal command protocol sequence (COMMAND_ACK regularly sent with result=MAV_RESULT_IN_PROGRESS, followed by a final result of MAV_RESULT_ACCEPTED or MAV_RESULT_FAILED). The operation can be cancelled, in which case the updating system would send COMMAND_ACK with MAV_RESULT_ACCEPTED. The operation can be restarted, in which case the updating system should respond with progress updates (as though it had a new message). |Component id of the component to be upgraded. If set to 0, all components should be upgraded.| 0: Start component upgrade, 1: Cancel component upgrade, 2: Restart component upgrade.| 0: Do not reboot component after the action is executed, 1: Reboot component after the action is executed.| Reserved| Reserved| Reserved| WIP: upgrade progress report rate (can be used for more granular control).|  */
+   MAV_CMD_DO_UPGRADE=247, /* Request a target system to start an upgrade of one (or all) of its components. For example, the command might be sent to a companion computer to cause it to upgrade a connected flight controller. The system doing the upgrade will report progress using the normal command protocol sequence for a long running operation. Command protocol information: https://mavlink.io/en/services/command.html. |Component id of the component to be upgraded. If set to 0, all components should be upgraded.| 0: Do not reboot component after the action is executed, 1: Reboot component after the action is executed.| Reserved| Reserved| Reserved| Reserved| WIP: upgrade progress report rate (can be used for more granular control).|  */
    MAV_CMD_OVERRIDE_GOTO=252, /* Override current mission with command to pause mission, pause mission and move to position, continue/resume mission. When param 1 indicates that the mission is paused (MAV_GOTO_DO_HOLD), param 2 defines whether it holds in place or moves to another position. |MAV_GOTO_DO_HOLD: pause mission and either hold or move to specified position (depending on param2), MAV_GOTO_DO_CONTINUE: resume mission.| MAV_GOTO_HOLD_AT_CURRENT_POSITION: hold at current position, MAV_GOTO_HOLD_AT_SPECIFIED_POSITION: hold at specified position.| Coordinate frame of hold point.| Desired yaw angle.| Latitude/X position.| Longitude/Y position.| Altitude/Z position.|  */
    MAV_CMD_MISSION_START=300, /* start running a mission |first_item: the first mission item to run| last_item:  the last mission item to run (after this item is run, the mission ends)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
    MAV_CMD_COMPONENT_ARM_DISARM=400, /* Arms / Disarms a component |0: disarm, 1: arm| 0: arm-disarm unless prevented by safety checks (i.e. when landed), 21196: force arming/disarming (e.g. allow arming to override preflight checks and disarming in flight)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */

ardupilotmega/version.h

@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Thu Jun 25 2020"
+#define MAVLINK_BUILD_DATE "Sat Jun 27 2020"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
  

autoquad/autoquad.h

@@ -157,7 +157,7 @@ typedef enum MAV_CMD
    MAV_CMD_PREFLIGHT_UAVCAN=243, /* Trigger UAVCAN config. This command will be only accepted if in pre-flight mode. |1: Trigger actuator ID assignment and direction mapping.| Reserved| Reserved| Reserved| Reserved| Reserved| Reserved|  */
    MAV_CMD_PREFLIGHT_STORAGE=245, /* Request storage of different parameter values and logs. This command will be only accepted if in pre-flight mode. |Parameter storage: 0: READ FROM FLASH/EEPROM, 1: WRITE CURRENT TO FLASH/EEPROM, 2: Reset to defaults| Mission storage: 0: READ FROM FLASH/EEPROM, 1: WRITE CURRENT TO FLASH/EEPROM, 2: Reset to defaults| Onboard logging: 0: Ignore, 1: Start default rate logging, -1: Stop logging, > 1: logging rate (e.g. set to 1000 for 1000 Hz logging)| Reserved| Empty| Empty| Empty|  */
    MAV_CMD_PREFLIGHT_REBOOT_SHUTDOWN=246, /* Request the reboot or shutdown of system components. |0: Do nothing for autopilot, 1: Reboot autopilot, 2: Shutdown autopilot, 3: Reboot autopilot and keep it in the bootloader until upgraded.| 0: Do nothing for onboard computer, 1: Reboot onboard computer, 2: Shutdown onboard computer, 3: Reboot onboard computer and keep it in the bootloader until upgraded.| WIP: 0: Do nothing for camera, 1: Reboot onboard camera, 2: Shutdown onboard camera, 3: Reboot onboard camera and keep it in the bootloader until upgraded| WIP: 0: Do nothing for mount (e.g. gimbal), 1: Reboot mount, 2: Shutdown mount, 3: Reboot mount and keep it in the bootloader until upgraded| Reserved (set to 0)| Reserved (set to 0)| WIP: ID (e.g. camera ID -1 for all IDs)|  */
-   MAV_CMD_DO_UPGRADE=247, /* Request a target system to start, cancel, or restart upgrade of one (or all) of its components. For example, the command might be sent to a companion computer to cause it to upgrade a connected flight controller. The system doing the upgrade will report progress using the normal command protocol sequence (COMMAND_ACK regularly sent with result=MAV_RESULT_IN_PROGRESS, followed by a final result of MAV_RESULT_ACCEPTED or MAV_RESULT_FAILED). The operation can be cancelled, in which case the updating system would send COMMAND_ACK with MAV_RESULT_ACCEPTED. The operation can be restarted, in which case the updating system should respond with progress updates (as though it had a new message). |Component id of the component to be upgraded. If set to 0, all components should be upgraded.| 0: Start component upgrade, 1: Cancel component upgrade, 2: Restart component upgrade.| 0: Do not reboot component after the action is executed, 1: Reboot component after the action is executed.| Reserved| Reserved| Reserved| WIP: upgrade progress report rate (can be used for more granular control).|  */
+   MAV_CMD_DO_UPGRADE=247, /* Request a target system to start an upgrade of one (or all) of its components. For example, the command might be sent to a companion computer to cause it to upgrade a connected flight controller. The system doing the upgrade will report progress using the normal command protocol sequence for a long running operation. Command protocol information: https://mavlink.io/en/services/command.html. |Component id of the component to be upgraded. If set to 0, all components should be upgraded.| 0: Do not reboot component after the action is executed, 1: Reboot component after the action is executed.| Reserved| Reserved| Reserved| Reserved| WIP: upgrade progress report rate (can be used for more granular control).|  */
    MAV_CMD_OVERRIDE_GOTO=252, /* Override current mission with command to pause mission, pause mission and move to position, continue/resume mission. When param 1 indicates that the mission is paused (MAV_GOTO_DO_HOLD), param 2 defines whether it holds in place or moves to another position. |MAV_GOTO_DO_HOLD: pause mission and either hold or move to specified position (depending on param2), MAV_GOTO_DO_CONTINUE: resume mission.| MAV_GOTO_HOLD_AT_CURRENT_POSITION: hold at current position, MAV_GOTO_HOLD_AT_SPECIFIED_POSITION: hold at specified position.| Coordinate frame of hold point.| Desired yaw angle.| Latitude/X position.| Longitude/Y position.| Altitude/Z position.|  */
    MAV_CMD_MISSION_START=300, /* start running a mission |first_item: the first mission item to run| last_item:  the last mission item to run (after this item is run, the mission ends)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
    MAV_CMD_COMPONENT_ARM_DISARM=400, /* Arms / Disarms a component |0: disarm, 1: arm| 0: arm-disarm unless prevented by safety checks (i.e. when landed), 21196: force arming/disarming (e.g. allow arming to override preflight checks and disarming in flight)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */

autoquad/version.h

@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Thu Jun 25 2020"
+#define MAVLINK_BUILD_DATE "Sat Jun 27 2020"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
  

common/common.h

@@ -776,7 +776,7 @@ typedef enum MAV_CMD
    MAV_CMD_PREFLIGHT_UAVCAN=243, /* Trigger UAVCAN config. This command will be only accepted if in pre-flight mode. |1: Trigger actuator ID assignment and direction mapping.| Reserved| Reserved| Reserved| Reserved| Reserved| Reserved|  */
    MAV_CMD_PREFLIGHT_STORAGE=245, /* Request storage of different parameter values and logs. This command will be only accepted if in pre-flight mode. |Parameter storage: 0: READ FROM FLASH/EEPROM, 1: WRITE CURRENT TO FLASH/EEPROM, 2: Reset to defaults| Mission storage: 0: READ FROM FLASH/EEPROM, 1: WRITE CURRENT TO FLASH/EEPROM, 2: Reset to defaults| Onboard logging: 0: Ignore, 1: Start default rate logging, -1: Stop logging, > 1: logging rate (e.g. set to 1000 for 1000 Hz logging)| Reserved| Empty| Empty| Empty|  */
    MAV_CMD_PREFLIGHT_REBOOT_SHUTDOWN=246, /* Request the reboot or shutdown of system components. |0: Do nothing for autopilot, 1: Reboot autopilot, 2: Shutdown autopilot, 3: Reboot autopilot and keep it in the bootloader until upgraded.| 0: Do nothing for onboard computer, 1: Reboot onboard computer, 2: Shutdown onboard computer, 3: Reboot onboard computer and keep it in the bootloader until upgraded.| WIP: 0: Do nothing for camera, 1: Reboot onboard camera, 2: Shutdown onboard camera, 3: Reboot onboard camera and keep it in the bootloader until upgraded| WIP: 0: Do nothing for mount (e.g. gimbal), 1: Reboot mount, 2: Shutdown mount, 3: Reboot mount and keep it in the bootloader until upgraded| Reserved (set to 0)| Reserved (set to 0)| WIP: ID (e.g. camera ID -1 for all IDs)|  */
-   MAV_CMD_DO_UPGRADE=247, /* Request a target system to start, cancel, or restart upgrade of one (or all) of its components. For example, the command might be sent to a companion computer to cause it to upgrade a connected flight controller. The system doing the upgrade will report progress using the normal command protocol sequence (COMMAND_ACK regularly sent with result=MAV_RESULT_IN_PROGRESS, followed by a final result of MAV_RESULT_ACCEPTED or MAV_RESULT_FAILED). The operation can be cancelled, in which case the updating system would send COMMAND_ACK with MAV_RESULT_ACCEPTED. The operation can be restarted, in which case the updating system should respond with progress updates (as though it had a new message). |Component id of the component to be upgraded. If set to 0, all components should be upgraded.| 0: Start component upgrade, 1: Cancel component upgrade, 2: Restart component upgrade.| 0: Do not reboot component after the action is executed, 1: Reboot component after the action is executed.| Reserved| Reserved| Reserved| WIP: upgrade progress report rate (can be used for more granular control).|  */
+   MAV_CMD_DO_UPGRADE=247, /* Request a target system to start an upgrade of one (or all) of its components. For example, the command might be sent to a companion computer to cause it to upgrade a connected flight controller. The system doing the upgrade will report progress using the normal command protocol sequence for a long running operation. Command protocol information: https://mavlink.io/en/services/command.html. |Component id of the component to be upgraded. If set to 0, all components should be upgraded.| 0: Do not reboot component after the action is executed, 1: Reboot component after the action is executed.| Reserved| Reserved| Reserved| Reserved| WIP: upgrade progress report rate (can be used for more granular control).|  */
    MAV_CMD_OVERRIDE_GOTO=252, /* Override current mission with command to pause mission, pause mission and move to position, continue/resume mission. When param 1 indicates that the mission is paused (MAV_GOTO_DO_HOLD), param 2 defines whether it holds in place or moves to another position. |MAV_GOTO_DO_HOLD: pause mission and either hold or move to specified position (depending on param2), MAV_GOTO_DO_CONTINUE: resume mission.| MAV_GOTO_HOLD_AT_CURRENT_POSITION: hold at current position, MAV_GOTO_HOLD_AT_SPECIFIED_POSITION: hold at specified position.| Coordinate frame of hold point.| Desired yaw angle.| Latitude/X position.| Longitude/Y position.| Altitude/Z position.|  */
    MAV_CMD_MISSION_START=300, /* start running a mission |first_item: the first mission item to run| last_item:  the last mission item to run (after this item is run, the mission ends)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
    MAV_CMD_COMPONENT_ARM_DISARM=400, /* Arms / Disarms a component |0: disarm, 1: arm| 0: arm-disarm unless prevented by safety checks (i.e. when landed), 21196: force arming/disarming (e.g. allow arming to override preflight checks and disarming in flight)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */

common/version.h

@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Thu Jun 25 2020"
+#define MAVLINK_BUILD_DATE "Sat Jun 27 2020"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
  

icarous/version.h

@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Thu Jun 25 2020"
+#define MAVLINK_BUILD_DATE "Sat Jun 27 2020"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
  

matrixpilot/matrixpilot.h

@@ -130,7 +130,7 @@ typedef enum MAV_CMD
    MAV_CMD_PREFLIGHT_UAVCAN=243, /* Trigger UAVCAN config. This command will be only accepted if in pre-flight mode. |1: Trigger actuator ID assignment and direction mapping.| Reserved| Reserved| Reserved| Reserved| Reserved| Reserved|  */
    MAV_CMD_PREFLIGHT_STORAGE=245, /* Request storage of different parameter values and logs. This command will be only accepted if in pre-flight mode. |Parameter storage: 0: READ FROM FLASH/EEPROM, 1: WRITE CURRENT TO FLASH/EEPROM, 2: Reset to defaults| Mission storage: 0: READ FROM FLASH/EEPROM, 1: WRITE CURRENT TO FLASH/EEPROM, 2: Reset to defaults| Onboard logging: 0: Ignore, 1: Start default rate logging, -1: Stop logging, > 1: logging rate (e.g. set to 1000 for 1000 Hz logging)| Reserved| Empty| Empty| Empty|  */
    MAV_CMD_PREFLIGHT_REBOOT_SHUTDOWN=246, /* Request the reboot or shutdown of system components. |0: Do nothing for autopilot, 1: Reboot autopilot, 2: Shutdown autopilot, 3: Reboot autopilot and keep it in the bootloader until upgraded.| 0: Do nothing for onboard computer, 1: Reboot onboard computer, 2: Shutdown onboard computer, 3: Reboot onboard computer and keep it in the bootloader until upgraded.| WIP: 0: Do nothing for camera, 1: Reboot onboard camera, 2: Shutdown onboard camera, 3: Reboot onboard camera and keep it in the bootloader until upgraded| WIP: 0: Do nothing for mount (e.g. gimbal), 1: Reboot mount, 2: Shutdown mount, 3: Reboot mount and keep it in the bootloader until upgraded| Reserved (set to 0)| Reserved (set to 0)| WIP: ID (e.g. camera ID -1 for all IDs)|  */
-   MAV_CMD_DO_UPGRADE=247, /* Request a target system to start, cancel, or restart upgrade of one (or all) of its components. For example, the command might be sent to a companion computer to cause it to upgrade a connected flight controller. The system doing the upgrade will report progress using the normal command protocol sequence (COMMAND_ACK regularly sent with result=MAV_RESULT_IN_PROGRESS, followed by a final result of MAV_RESULT_ACCEPTED or MAV_RESULT_FAILED). The operation can be cancelled, in which case the updating system would send COMMAND_ACK with MAV_RESULT_ACCEPTED. The operation can be restarted, in which case the updating system should respond with progress updates (as though it had a new message). |Component id of the component to be upgraded. If set to 0, all components should be upgraded.| 0: Start component upgrade, 1: Cancel component upgrade, 2: Restart component upgrade.| 0: Do not reboot component after the action is executed, 1: Reboot component after the action is executed.| Reserved| Reserved| Reserved| WIP: upgrade progress report rate (can be used for more granular control).|  */
+   MAV_CMD_DO_UPGRADE=247, /* Request a target system to start an upgrade of one (or all) of its components. For example, the command might be sent to a companion computer to cause it to upgrade a connected flight controller. The system doing the upgrade will report progress using the normal command protocol sequence for a long running operation. Command protocol information: https://mavlink.io/en/services/command.html. |Component id of the component to be upgraded. If set to 0, all components should be upgraded.| 0: Do not reboot component after the action is executed, 1: Reboot component after the action is executed.| Reserved| Reserved| Reserved| Reserved| WIP: upgrade progress report rate (can be used for more granular control).|  */
    MAV_CMD_OVERRIDE_GOTO=252, /* Override current mission with command to pause mission, pause mission and move to position, continue/resume mission. When param 1 indicates that the mission is paused (MAV_GOTO_DO_HOLD), param 2 defines whether it holds in place or moves to another position. |MAV_GOTO_DO_HOLD: pause mission and either hold or move to specified position (depending on param2), MAV_GOTO_DO_CONTINUE: resume mission.| MAV_GOTO_HOLD_AT_CURRENT_POSITION: hold at current position, MAV_GOTO_HOLD_AT_SPECIFIED_POSITION: hold at specified position.| Coordinate frame of hold point.| Desired yaw angle.| Latitude/X position.| Longitude/Y position.| Altitude/Z position.|  */
    MAV_CMD_MISSION_START=300, /* start running a mission |first_item: the first mission item to run| last_item:  the last mission item to run (after this item is run, the mission ends)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
    MAV_CMD_COMPONENT_ARM_DISARM=400, /* Arms / Disarms a component |0: disarm, 1: arm| 0: arm-disarm unless prevented by safety checks (i.e. when landed), 21196: force arming/disarming (e.g. allow arming to override preflight checks and disarming in flight)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */

matrixpilot/version.h

@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Thu Jun 25 2020"
+#define MAVLINK_BUILD_DATE "Sat Jun 27 2020"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
  

message_definitions/common.xml

@@ -2064,10 +2064,10 @@
       </entry>
       <entry value="247" name="MAV_CMD_DO_UPGRADE" hasLocation="false" isDestination="false">
         <wip/>
-        <description>Request a target system to start, cancel, or restart upgrade of one (or all) of its components. For example, the command might be sent to a companion computer to cause it to upgrade a connected flight controller. The system doing the upgrade will report progress using the normal command protocol sequence (COMMAND_ACK regularly sent with result=MAV_RESULT_IN_PROGRESS, followed by a final result of MAV_RESULT_ACCEPTED or MAV_RESULT_FAILED). The operation can be cancelled, in which case the updating system would send COMMAND_ACK with MAV_RESULT_ACCEPTED. The operation can be restarted, in which case the updating system should respond with progress updates (as though it had a new message).</description>
+        <description>Request a target system to start an upgrade of one (or all) of its components. For example, the command might be sent to a companion computer to cause it to upgrade a connected flight controller. The system doing the upgrade will report progress using the normal command protocol sequence for a long running operation. Command protocol information: https://mavlink.io/en/services/command.html.</description>
         <param index="1" label="Component ID" enum="MAV_COMPONENT">Component id of the component to be upgraded. If set to 0, all components should be upgraded.</param>
-        <param index="2" label="Action" minValue="0" maxValue="2" increment="1">0: Start component upgrade, 1: Cancel component upgrade, 2: Restart component upgrade.</param>
-        <param index="3" label="Reboot" minValue="0" maxValue="1" increment="1">0: Do not reboot component after the action is executed, 1: Reboot component after the action is executed.</param>
+        <param index="2" label="Reboot" minValue="0" maxValue="1" increment="1">0: Do not reboot component after the action is executed, 1: Reboot component after the action is executed.</param>
+        <param index="3">Reserved</param>
         <param index="4">Reserved</param>
         <param index="5">Reserved</param>
         <param index="6">Reserved</param>

minimal/version.h

@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Thu Jun 25 2020"
+#define MAVLINK_BUILD_DATE "Sat Jun 27 2020"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 22
  

slugs/slugs.h

@@ -113,7 +113,7 @@ typedef enum MAV_CMD
    MAV_CMD_PREFLIGHT_UAVCAN=243, /* Trigger UAVCAN config. This command will be only accepted if in pre-flight mode. |1: Trigger actuator ID assignment and direction mapping.| Reserved| Reserved| Reserved| Reserved| Reserved| Reserved|  */
    MAV_CMD_PREFLIGHT_STORAGE=245, /* Request storage of different parameter values and logs. This command will be only accepted if in pre-flight mode. |Parameter storage: 0: READ FROM FLASH/EEPROM, 1: WRITE CURRENT TO FLASH/EEPROM, 2: Reset to defaults| Mission storage: 0: READ FROM FLASH/EEPROM, 1: WRITE CURRENT TO FLASH/EEPROM, 2: Reset to defaults| Onboard logging: 0: Ignore, 1: Start default rate logging, -1: Stop logging, > 1: logging rate (e.g. set to 1000 for 1000 Hz logging)| Reserved| Empty| Empty| Empty|  */
    MAV_CMD_PREFLIGHT_REBOOT_SHUTDOWN=246, /* Request the reboot or shutdown of system components. |0: Do nothing for autopilot, 1: Reboot autopilot, 2: Shutdown autopilot, 3: Reboot autopilot and keep it in the bootloader until upgraded.| 0: Do nothing for onboard computer, 1: Reboot onboard computer, 2: Shutdown onboard computer, 3: Reboot onboard computer and keep it in the bootloader until upgraded.| WIP: 0: Do nothing for camera, 1: Reboot onboard camera, 2: Shutdown onboard camera, 3: Reboot onboard camera and keep it in the bootloader until upgraded| WIP: 0: Do nothing for mount (e.g. gimbal), 1: Reboot mount, 2: Shutdown mount, 3: Reboot mount and keep it in the bootloader until upgraded| Reserved (set to 0)| Reserved (set to 0)| WIP: ID (e.g. camera ID -1 for all IDs)|  */
-   MAV_CMD_DO_UPGRADE=247, /* Request a target system to start, cancel, or restart upgrade of one (or all) of its components. For example, the command might be sent to a companion computer to cause it to upgrade a connected flight controller. The system doing the upgrade will report progress using the normal command protocol sequence (COMMAND_ACK regularly sent with result=MAV_RESULT_IN_PROGRESS, followed by a final result of MAV_RESULT_ACCEPTED or MAV_RESULT_FAILED). The operation can be cancelled, in which case the updating system would send COMMAND_ACK with MAV_RESULT_ACCEPTED. The operation can be restarted, in which case the updating system should respond with progress updates (as though it had a new message). |Component id of the component to be upgraded. If set to 0, all components should be upgraded.| 0: Start component upgrade, 1: Cancel component upgrade, 2: Restart component upgrade.| 0: Do not reboot component after the action is executed, 1: Reboot component after the action is executed.| Reserved| Reserved| Reserved| WIP: upgrade progress report rate (can be used for more granular control).|  */
+   MAV_CMD_DO_UPGRADE=247, /* Request a target system to start an upgrade of one (or all) of its components. For example, the command might be sent to a companion computer to cause it to upgrade a connected flight controller. The system doing the upgrade will report progress using the normal command protocol sequence for a long running operation. Command protocol information: https://mavlink.io/en/services/command.html. |Component id of the component to be upgraded. If set to 0, all components should be upgraded.| 0: Do not reboot component after the action is executed, 1: Reboot component after the action is executed.| Reserved| Reserved| Reserved| Reserved| WIP: upgrade progress report rate (can be used for more granular control).|  */
    MAV_CMD_OVERRIDE_GOTO=252, /* Override current mission with command to pause mission, pause mission and move to position, continue/resume mission. When param 1 indicates that the mission is paused (MAV_GOTO_DO_HOLD), param 2 defines whether it holds in place or moves to another position. |MAV_GOTO_DO_HOLD: pause mission and either hold or move to specified position (depending on param2), MAV_GOTO_DO_CONTINUE: resume mission.| MAV_GOTO_HOLD_AT_CURRENT_POSITION: hold at current position, MAV_GOTO_HOLD_AT_SPECIFIED_POSITION: hold at specified position.| Coordinate frame of hold point.| Desired yaw angle.| Latitude/X position.| Longitude/Y position.| Altitude/Z position.|  */
    MAV_CMD_MISSION_START=300, /* start running a mission |first_item: the first mission item to run| last_item:  the last mission item to run (after this item is run, the mission ends)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
    MAV_CMD_COMPONENT_ARM_DISARM=400, /* Arms / Disarms a component |0: disarm, 1: arm| 0: arm-disarm unless prevented by safety checks (i.e. when landed), 21196: force arming/disarming (e.g. allow arming to override preflight checks and disarming in flight)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */

slugs/version.h

@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Thu Jun 25 2020"
+#define MAVLINK_BUILD_DATE "Sat Jun 27 2020"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
  

standard/version.h

@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Thu Jun 25 2020"
+#define MAVLINK_BUILD_DATE "Sat Jun 27 2020"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
  

test/version.h

@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Thu Jun 25 2020"
+#define MAVLINK_BUILD_DATE "Sat Jun 27 2020"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 179
  

uAvionix/version.h

@@ -7,7 +7,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Thu Jun 25 2020"
+#define MAVLINK_BUILD_DATE "Sat Jun 27 2020"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "2.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255