autogenerated headers for rev...

autogenerated headers for rev https://github.com/mavlink/mavlink/tree/c4f2fa3c13f8a99069d07136d648cb2a7dbabe16

ASLUAV/ASLUAV.h

@@ -122,7 +122,7 @@ typedef enum MAV_CMD
    MAV_CMD_START_RX_PAIR=500, /* Starts receiver pairing. |0:Spektrum.| RC type.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
    MAV_CMD_GET_MESSAGE_INTERVAL=510, /* Request the interval between messages for a particular MAVLink message ID. The receiver should ACK the command and then emit its response in a MESSAGE_INTERVAL message. |The MAVLink message ID| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
    MAV_CMD_SET_MESSAGE_INTERVAL=511, /* Set the interval between messages for a particular MAVLink message ID. This interface replaces REQUEST_DATA_STREAM. |The MAVLink message ID| The interval between two messages. Set to -1 to disable and 0 to request default rate.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Target address of message stream (if message has target address fields). 0: Flight-stack default (recommended), 1: address of requestor, 2: broadcast.|  */
-   MAV_CMD_REQUEST_MESSAGE=512, /* Request the target system(s) emit a single instance of a specified message (i.e. a "one-shot" version of MAV_CMD_SET_MESSAGE_INTERVAL). |The MAVLink message ID of the requested message.| Index id (if appropriate). The use of this parameter (if any), must be defined in the requested message.| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| Target address for requested message (if message has target address fields). 0: Flight-stack default, 1: address of requestor, 2: broadcast.|  */
+   MAV_CMD_REQUEST_MESSAGE=512, /* Request the target system(s) emit a single instance of a specified message (i.e. a "one-shot" version of MAV_CMD_SET_MESSAGE_INTERVAL). |The MAVLink message ID of the requested message.| Use for index ID, if required. Otherwise, the use of this parameter (if any) must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| Target address for requested message (if message has target address fields). 0: Flight-stack default, 1: address of requestor, 2: broadcast.|  */
    MAV_CMD_REQUEST_PROTOCOL_VERSION=519, /* Request MAVLink protocol version compatibility. All receivers should ACK the command and then emit their capabilities in an PROTOCOL_VERSION message |1: Request supported protocol versions by all nodes on the network| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
    MAV_CMD_REQUEST_AUTOPILOT_CAPABILITIES=520, /* Request autopilot capabilities. The receiver should ACK the command and then emit its capabilities in an AUTOPILOT_VERSION message |1: Request autopilot version| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
    MAV_CMD_REQUEST_CAMERA_INFORMATION=521, /* Request camera information (CAMERA_INFORMATION). |0: No action 1: Request camera capabilities| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */

ardupilotmega/ardupilotmega.h

@@ -143,7 +143,7 @@ typedef enum MAV_CMD
    MAV_CMD_START_RX_PAIR=500, /* Starts receiver pairing. |0:Spektrum.| RC type.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
    MAV_CMD_GET_MESSAGE_INTERVAL=510, /* Request the interval between messages for a particular MAVLink message ID. The receiver should ACK the command and then emit its response in a MESSAGE_INTERVAL message. |The MAVLink message ID| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
    MAV_CMD_SET_MESSAGE_INTERVAL=511, /* Set the interval between messages for a particular MAVLink message ID. This interface replaces REQUEST_DATA_STREAM. |The MAVLink message ID| The interval between two messages. Set to -1 to disable and 0 to request default rate.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Target address of message stream (if message has target address fields). 0: Flight-stack default (recommended), 1: address of requestor, 2: broadcast.|  */
-   MAV_CMD_REQUEST_MESSAGE=512, /* Request the target system(s) emit a single instance of a specified message (i.e. a "one-shot" version of MAV_CMD_SET_MESSAGE_INTERVAL). |The MAVLink message ID of the requested message.| Index id (if appropriate). The use of this parameter (if any), must be defined in the requested message.| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| Target address for requested message (if message has target address fields). 0: Flight-stack default, 1: address of requestor, 2: broadcast.|  */
+   MAV_CMD_REQUEST_MESSAGE=512, /* Request the target system(s) emit a single instance of a specified message (i.e. a "one-shot" version of MAV_CMD_SET_MESSAGE_INTERVAL). |The MAVLink message ID of the requested message.| Use for index ID, if required. Otherwise, the use of this parameter (if any) must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| Target address for requested message (if message has target address fields). 0: Flight-stack default, 1: address of requestor, 2: broadcast.|  */
    MAV_CMD_REQUEST_PROTOCOL_VERSION=519, /* Request MAVLink protocol version compatibility. All receivers should ACK the command and then emit their capabilities in an PROTOCOL_VERSION message |1: Request supported protocol versions by all nodes on the network| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
    MAV_CMD_REQUEST_AUTOPILOT_CAPABILITIES=520, /* Request autopilot capabilities. The receiver should ACK the command and then emit its capabilities in an AUTOPILOT_VERSION message |1: Request autopilot version| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
    MAV_CMD_REQUEST_CAMERA_INFORMATION=521, /* Request camera information (CAMERA_INFORMATION). |0: No action 1: Request camera capabilities| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */

autoquad/autoquad.h

@@ -166,7 +166,7 @@ typedef enum MAV_CMD
    MAV_CMD_START_RX_PAIR=500, /* Starts receiver pairing. |0:Spektrum.| RC type.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
    MAV_CMD_GET_MESSAGE_INTERVAL=510, /* Request the interval between messages for a particular MAVLink message ID. The receiver should ACK the command and then emit its response in a MESSAGE_INTERVAL message. |The MAVLink message ID| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
    MAV_CMD_SET_MESSAGE_INTERVAL=511, /* Set the interval between messages for a particular MAVLink message ID. This interface replaces REQUEST_DATA_STREAM. |The MAVLink message ID| The interval between two messages. Set to -1 to disable and 0 to request default rate.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Target address of message stream (if message has target address fields). 0: Flight-stack default (recommended), 1: address of requestor, 2: broadcast.|  */
-   MAV_CMD_REQUEST_MESSAGE=512, /* Request the target system(s) emit a single instance of a specified message (i.e. a "one-shot" version of MAV_CMD_SET_MESSAGE_INTERVAL). |The MAVLink message ID of the requested message.| Index id (if appropriate). The use of this parameter (if any), must be defined in the requested message.| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| Target address for requested message (if message has target address fields). 0: Flight-stack default, 1: address of requestor, 2: broadcast.|  */
+   MAV_CMD_REQUEST_MESSAGE=512, /* Request the target system(s) emit a single instance of a specified message (i.e. a "one-shot" version of MAV_CMD_SET_MESSAGE_INTERVAL). |The MAVLink message ID of the requested message.| Use for index ID, if required. Otherwise, the use of this parameter (if any) must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| Target address for requested message (if message has target address fields). 0: Flight-stack default, 1: address of requestor, 2: broadcast.|  */
    MAV_CMD_REQUEST_PROTOCOL_VERSION=519, /* Request MAVLink protocol version compatibility. All receivers should ACK the command and then emit their capabilities in an PROTOCOL_VERSION message |1: Request supported protocol versions by all nodes on the network| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
    MAV_CMD_REQUEST_AUTOPILOT_CAPABILITIES=520, /* Request autopilot capabilities. The receiver should ACK the command and then emit its capabilities in an AUTOPILOT_VERSION message |1: Request autopilot version| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
    MAV_CMD_REQUEST_CAMERA_INFORMATION=521, /* Request camera information (CAMERA_INFORMATION). |0: No action 1: Request camera capabilities| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */

common/common.h

@@ -769,7 +769,7 @@ typedef enum MAV_CMD
    MAV_CMD_START_RX_PAIR=500, /* Starts receiver pairing. |0:Spektrum.| RC type.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
    MAV_CMD_GET_MESSAGE_INTERVAL=510, /* Request the interval between messages for a particular MAVLink message ID. The receiver should ACK the command and then emit its response in a MESSAGE_INTERVAL message. |The MAVLink message ID| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
    MAV_CMD_SET_MESSAGE_INTERVAL=511, /* Set the interval between messages for a particular MAVLink message ID. This interface replaces REQUEST_DATA_STREAM. |The MAVLink message ID| The interval between two messages. Set to -1 to disable and 0 to request default rate.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Target address of message stream (if message has target address fields). 0: Flight-stack default (recommended), 1: address of requestor, 2: broadcast.|  */
-   MAV_CMD_REQUEST_MESSAGE=512, /* Request the target system(s) emit a single instance of a specified message (i.e. a "one-shot" version of MAV_CMD_SET_MESSAGE_INTERVAL). |The MAVLink message ID of the requested message.| Index id (if appropriate). The use of this parameter (if any), must be defined in the requested message.| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| Target address for requested message (if message has target address fields). 0: Flight-stack default, 1: address of requestor, 2: broadcast.|  */
+   MAV_CMD_REQUEST_MESSAGE=512, /* Request the target system(s) emit a single instance of a specified message (i.e. a "one-shot" version of MAV_CMD_SET_MESSAGE_INTERVAL). |The MAVLink message ID of the requested message.| Use for index ID, if required. Otherwise, the use of this parameter (if any) must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| Target address for requested message (if message has target address fields). 0: Flight-stack default, 1: address of requestor, 2: broadcast.|  */
    MAV_CMD_REQUEST_PROTOCOL_VERSION=519, /* Request MAVLink protocol version compatibility. All receivers should ACK the command and then emit their capabilities in an PROTOCOL_VERSION message |1: Request supported protocol versions by all nodes on the network| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
    MAV_CMD_REQUEST_AUTOPILOT_CAPABILITIES=520, /* Request autopilot capabilities. The receiver should ACK the command and then emit its capabilities in an AUTOPILOT_VERSION message |1: Request autopilot version| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
    MAV_CMD_REQUEST_CAMERA_INFORMATION=521, /* Request camera information (CAMERA_INFORMATION). |0: No action 1: Request camera capabilities| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */

matrixpilot/matrixpilot.h

@@ -139,7 +139,7 @@ typedef enum MAV_CMD
    MAV_CMD_START_RX_PAIR=500, /* Starts receiver pairing. |0:Spektrum.| RC type.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
    MAV_CMD_GET_MESSAGE_INTERVAL=510, /* Request the interval between messages for a particular MAVLink message ID. The receiver should ACK the command and then emit its response in a MESSAGE_INTERVAL message. |The MAVLink message ID| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
    MAV_CMD_SET_MESSAGE_INTERVAL=511, /* Set the interval between messages for a particular MAVLink message ID. This interface replaces REQUEST_DATA_STREAM. |The MAVLink message ID| The interval between two messages. Set to -1 to disable and 0 to request default rate.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Target address of message stream (if message has target address fields). 0: Flight-stack default (recommended), 1: address of requestor, 2: broadcast.|  */
-   MAV_CMD_REQUEST_MESSAGE=512, /* Request the target system(s) emit a single instance of a specified message (i.e. a "one-shot" version of MAV_CMD_SET_MESSAGE_INTERVAL). |The MAVLink message ID of the requested message.| Index id (if appropriate). The use of this parameter (if any), must be defined in the requested message.| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| Target address for requested message (if message has target address fields). 0: Flight-stack default, 1: address of requestor, 2: broadcast.|  */
+   MAV_CMD_REQUEST_MESSAGE=512, /* Request the target system(s) emit a single instance of a specified message (i.e. a "one-shot" version of MAV_CMD_SET_MESSAGE_INTERVAL). |The MAVLink message ID of the requested message.| Use for index ID, if required. Otherwise, the use of this parameter (if any) must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| Target address for requested message (if message has target address fields). 0: Flight-stack default, 1: address of requestor, 2: broadcast.|  */
    MAV_CMD_REQUEST_PROTOCOL_VERSION=519, /* Request MAVLink protocol version compatibility. All receivers should ACK the command and then emit their capabilities in an PROTOCOL_VERSION message |1: Request supported protocol versions by all nodes on the network| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
    MAV_CMD_REQUEST_AUTOPILOT_CAPABILITIES=520, /* Request autopilot capabilities. The receiver should ACK the command and then emit its capabilities in an AUTOPILOT_VERSION message |1: Request autopilot version| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
    MAV_CMD_REQUEST_CAMERA_INFORMATION=521, /* Request camera information (CAMERA_INFORMATION). |0: No action 1: Request camera capabilities| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */

message_definitions/common.xml

@@ -2100,7 +2100,7 @@
       <entry value="512" name="MAV_CMD_REQUEST_MESSAGE" hasLocation="false" isDestination="false">
         <description>Request the target system(s) emit a single instance of a specified message (i.e. a "one-shot" version of MAV_CMD_SET_MESSAGE_INTERVAL).</description>
         <param index="1" label="Message ID" minValue="0" maxValue="16777215" increment="1">The MAVLink message ID of the requested message.</param>
-        <param index="2" label="Index ID" minValue="0" increment="1">Index id (if appropriate). The use of this parameter (if any), must be defined in the requested message.</param>
+        <param index="2">Use for index ID, if required. Otherwise, the use of this parameter (if any) must be defined in the requested message. By default assumed not used (0).</param>
         <param index="3">The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).</param>
         <param index="4">The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).</param>
         <param index="5">The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).</param>

message_definitions/minimal.xml

@@ -619,6 +619,11 @@
         <description>Request the target system(s) emit a single instance of a specified message (i.e. a "one-shot" version of MAV_CMD_SET_MESSAGE_INTERVAL).</description>
         <param index="1" label="Message ID" minValue="0" maxValue="16777215" increment="1">The MAVLink message ID of the requested message.</param>
         <param index="2" label="Index ID" minValue="0" increment="1">Index id (if appropriate). The use of this parameter (if any), must be defined in the requested message.</param>
+        <param index="3">The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).</param>
+        <param index="4">The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).</param>
+        <param index="5">The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).</param>
+        <param index="6">The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).</param>
+        <param index="7" label="Response Target" minValue="0" maxValue="2" increment="1">Target address for requested message (if message has target address fields). 0: Flight-stack default, 1: address of requestor, 2: broadcast.</param>
       </entry>
       <entry value="519" name="MAV_CMD_REQUEST_PROTOCOL_VERSION" hasLocation="false" isDestination="false">
         <deprecated since="2019-08" replaced_by="MAV_CMD_REQUEST_MESSAGE"/>

minimal/minimal.h

@@ -291,7 +291,7 @@ typedef enum MAV_COMPONENT
 #define HAVE_ENUM_MAV_CMD
 typedef enum MAV_CMD
 {
-   MAV_CMD_REQUEST_MESSAGE=512, /* Request the target system(s) emit a single instance of a specified message (i.e. a "one-shot" version of MAV_CMD_SET_MESSAGE_INTERVAL). |The MAVLink message ID of the requested message.| Index id (if appropriate). The use of this parameter (if any), must be defined in the requested message.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
+   MAV_CMD_REQUEST_MESSAGE=512, /* Request the target system(s) emit a single instance of a specified message (i.e. a "one-shot" version of MAV_CMD_SET_MESSAGE_INTERVAL). |The MAVLink message ID of the requested message.| Index id (if appropriate). The use of this parameter (if any), must be defined in the requested message.| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| Target address for requested message (if message has target address fields). 0: Flight-stack default, 1: address of requestor, 2: broadcast.|  */
    MAV_CMD_REQUEST_PROTOCOL_VERSION=519, /* Request MAVLink protocol version compatibility |1: Request supported protocol versions by all nodes on the network| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
    MAV_CMD_ENUM_END=520, /*  | */
 } MAV_CMD;

slugs/slugs.h

@@ -122,7 +122,7 @@ typedef enum MAV_CMD
    MAV_CMD_START_RX_PAIR=500, /* Starts receiver pairing. |0:Spektrum.| RC type.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
    MAV_CMD_GET_MESSAGE_INTERVAL=510, /* Request the interval between messages for a particular MAVLink message ID. The receiver should ACK the command and then emit its response in a MESSAGE_INTERVAL message. |The MAVLink message ID| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
    MAV_CMD_SET_MESSAGE_INTERVAL=511, /* Set the interval between messages for a particular MAVLink message ID. This interface replaces REQUEST_DATA_STREAM. |The MAVLink message ID| The interval between two messages. Set to -1 to disable and 0 to request default rate.| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Target address of message stream (if message has target address fields). 0: Flight-stack default (recommended), 1: address of requestor, 2: broadcast.|  */
-   MAV_CMD_REQUEST_MESSAGE=512, /* Request the target system(s) emit a single instance of a specified message (i.e. a "one-shot" version of MAV_CMD_SET_MESSAGE_INTERVAL). |The MAVLink message ID of the requested message.| Index id (if appropriate). The use of this parameter (if any), must be defined in the requested message.| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| Target address for requested message (if message has target address fields). 0: Flight-stack default, 1: address of requestor, 2: broadcast.|  */
+   MAV_CMD_REQUEST_MESSAGE=512, /* Request the target system(s) emit a single instance of a specified message (i.e. a "one-shot" version of MAV_CMD_SET_MESSAGE_INTERVAL). |The MAVLink message ID of the requested message.| Use for index ID, if required. Otherwise, the use of this parameter (if any) must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| The use of this parameter (if any), must be defined in the requested message. By default assumed not used (0).| Target address for requested message (if message has target address fields). 0: Flight-stack default, 1: address of requestor, 2: broadcast.|  */
    MAV_CMD_REQUEST_PROTOCOL_VERSION=519, /* Request MAVLink protocol version compatibility. All receivers should ACK the command and then emit their capabilities in an PROTOCOL_VERSION message |1: Request supported protocol versions by all nodes on the network| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
    MAV_CMD_REQUEST_AUTOPILOT_CAPABILITIES=520, /* Request autopilot capabilities. The receiver should ACK the command and then emit its capabilities in an AUTOPILOT_VERSION message |1: Request autopilot version| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */
    MAV_CMD_REQUEST_CAMERA_INFORMATION=521, /* Request camera information (CAMERA_INFORMATION). |0: No action 1: Request camera capabilities| Reserved (all remaining params)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)| Reserved (default:0)|  */