autogenerated headers for rev...

autogenerated headers for rev https://github.com/mavlink/mavlink/tree/4a8588399b8ad014726dcddcf2311535cb445a07

ASLUAV/ASLUAV.h

@@ -76,6 +76,8 @@ typedef enum MAV_CMD
 	MAV_CMD_DO_LAND_START=189, /* Mission command to perform a landing. This is used as a marker in a mission to tell the autopilot where a sequence of mission items that represents a landing starts. It may also be sent via a COMMAND_LONG to trigger a landing, in which case the nearest (geographically) landing sequence in the mission will be used. The Latitude/Longitude is optional, and may be set to 0/0 if not needed. If specified then it will be used to help find the closest landing sequence. |Empty| Empty| Empty| Empty| Latitude| Longitude| Empty|  */
 	MAV_CMD_DO_RALLY_LAND=190, /* Mission command to perform a landing from a rally point. |Break altitude (meters)| Landing speed (m/s)| Empty| Empty| Empty| Empty| Empty|  */
 	MAV_CMD_DO_GO_AROUND=191, /* Mission command to safely abort an autonmous landing. |Altitude (meters)| Empty| Empty| Empty| Empty| Empty| Empty|  */
+	MAV_CMD_DO_REPOSITION=192, /* Reposition the vehicle to a specific WGS84 global position. |Ground speed, less than 0 (-1) for default| Reserved| Reserved| Yaw heading, NaN for unchanged| Latitude (deg * 1E7)| Longitude (deg * 1E7)| Altitude (meters)|  */
+	MAV_CMD_DO_PAUSE_CONTINUE=193, /* If in a GPS controlled position mode, hold the current position or continue. |0: Pause current mission or reposition command, hold current position. 1: Continue mission. A VTOL capable vehicle should enter hover mode (multicopter and VTOL planes). A plane should loiter with the default loiter radius.| Reserved| Reserved| Reserved| Reserved| Reserved| Reserved|  */
 	MAV_CMD_DO_CONTROL_VIDEO=200, /* Control onboard camera system. |Camera ID (-1 for all)| Transmission: 0: disabled, 1: enabled compressed, 2: enabled raw| Transmission mode: 0: video stream, >0: single images every n seconds (decimal)| Recording: 0: disabled, 1: enabled compressed, 2: enabled raw| Empty| Empty| Empty|  */
 	MAV_CMD_DO_SET_ROI=201, /* Sets the region of interest (ROI) for a sensor set or the vehicle itself. This can then be used by the vehicles control system to control the vehicle attitude and the attitude of various sensors such as cameras. |Region of intereset mode. (see MAV_ROI enum)| MISSION index/ target ID. (see MAV_ROI enum)| ROI index (allows a vehicle to manage multiple ROI's)| Empty| x the location of the fixed ROI (see MAV_FRAME)| y| z|  */
 	MAV_CMD_DO_DIGICAM_CONFIGURE=202, /* Mission command to configure an on-board camera controller system. |Modes: P, TV, AV, M, Etc| Shutter speed: Divisor number for one second| Aperture: F stop number| ISO number e.g. 80, 100, 200, Etc| Exposure type enumerator| Command Identity| Main engine cut-off time before camera trigger in seconds/10 (0 means no cut-off)|  */

ASLUAV/version.h

@@ -5,7 +5,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Fri Feb 26 2016"
+#define MAVLINK_BUILD_DATE "Sat Feb 27 2016"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "1.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
  

ardupilotmega/ardupilotmega.h

@@ -77,6 +77,8 @@ typedef enum MAV_CMD
 	MAV_CMD_DO_LAND_START=189, /* Mission command to perform a landing. This is used as a marker in a mission to tell the autopilot where a sequence of mission items that represents a landing starts. It may also be sent via a COMMAND_LONG to trigger a landing, in which case the nearest (geographically) landing sequence in the mission will be used. The Latitude/Longitude is optional, and may be set to 0/0 if not needed. If specified then it will be used to help find the closest landing sequence. |Empty| Empty| Empty| Empty| Latitude| Longitude| Empty|  */
 	MAV_CMD_DO_RALLY_LAND=190, /* Mission command to perform a landing from a rally point. |Break altitude (meters)| Landing speed (m/s)| Empty| Empty| Empty| Empty| Empty|  */
 	MAV_CMD_DO_GO_AROUND=191, /* Mission command to safely abort an autonmous landing. |Altitude (meters)| Empty| Empty| Empty| Empty| Empty| Empty|  */
+	MAV_CMD_DO_REPOSITION=192, /* Reposition the vehicle to a specific WGS84 global position. |Ground speed, less than 0 (-1) for default| Reserved| Reserved| Yaw heading, NaN for unchanged| Latitude (deg * 1E7)| Longitude (deg * 1E7)| Altitude (meters)|  */
+	MAV_CMD_DO_PAUSE_CONTINUE=193, /* If in a GPS controlled position mode, hold the current position or continue. |0: Pause current mission or reposition command, hold current position. 1: Continue mission. A VTOL capable vehicle should enter hover mode (multicopter and VTOL planes). A plane should loiter with the default loiter radius.| Reserved| Reserved| Reserved| Reserved| Reserved| Reserved|  */
 	MAV_CMD_DO_CONTROL_VIDEO=200, /* Control onboard camera system. |Camera ID (-1 for all)| Transmission: 0: disabled, 1: enabled compressed, 2: enabled raw| Transmission mode: 0: video stream, >0: single images every n seconds (decimal)| Recording: 0: disabled, 1: enabled compressed, 2: enabled raw| Empty| Empty| Empty|  */
 	MAV_CMD_DO_SET_ROI=201, /* Sets the region of interest (ROI) for a sensor set or the vehicle itself. This can then be used by the vehicles control system to control the vehicle attitude and the attitude of various sensors such as cameras. |Region of intereset mode. (see MAV_ROI enum)| MISSION index/ target ID. (see MAV_ROI enum)| ROI index (allows a vehicle to manage multiple ROI's)| Empty| x the location of the fixed ROI (see MAV_FRAME)| y| z|  */
 	MAV_CMD_DO_DIGICAM_CONFIGURE=202, /* Mission command to configure an on-board camera controller system. |Modes: P, TV, AV, M, Etc| Shutter speed: Divisor number for one second| Aperture: F stop number| ISO number e.g. 80, 100, 200, Etc| Exposure type enumerator| Command Identity| Main engine cut-off time before camera trigger in seconds/10 (0 means no cut-off)|  */

ardupilotmega/version.h

@@ -5,7 +5,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Fri Feb 26 2016"
+#define MAVLINK_BUILD_DATE "Sat Feb 27 2016"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "1.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
  

autoquad/autoquad.h

@@ -103,6 +103,8 @@ typedef enum MAV_CMD
 	MAV_CMD_DO_LAND_START=189, /* Mission command to perform a landing. This is used as a marker in a mission to tell the autopilot where a sequence of mission items that represents a landing starts. It may also be sent via a COMMAND_LONG to trigger a landing, in which case the nearest (geographically) landing sequence in the mission will be used. The Latitude/Longitude is optional, and may be set to 0/0 if not needed. If specified then it will be used to help find the closest landing sequence. |Empty| Empty| Empty| Empty| Latitude| Longitude| Empty|  */
 	MAV_CMD_DO_RALLY_LAND=190, /* Mission command to perform a landing from a rally point. |Break altitude (meters)| Landing speed (m/s)| Empty| Empty| Empty| Empty| Empty|  */
 	MAV_CMD_DO_GO_AROUND=191, /* Mission command to safely abort an autonmous landing. |Altitude (meters)| Empty| Empty| Empty| Empty| Empty| Empty|  */
+	MAV_CMD_DO_REPOSITION=192, /* Reposition the vehicle to a specific WGS84 global position. |Ground speed, less than 0 (-1) for default| Reserved| Reserved| Yaw heading, NaN for unchanged| Latitude (deg * 1E7)| Longitude (deg * 1E7)| Altitude (meters)|  */
+	MAV_CMD_DO_PAUSE_CONTINUE=193, /* If in a GPS controlled position mode, hold the current position or continue. |0: Pause current mission or reposition command, hold current position. 1: Continue mission. A VTOL capable vehicle should enter hover mode (multicopter and VTOL planes). A plane should loiter with the default loiter radius.| Reserved| Reserved| Reserved| Reserved| Reserved| Reserved|  */
 	MAV_CMD_DO_CONTROL_VIDEO=200, /* Control onboard camera system. |Camera ID (-1 for all)| Transmission: 0: disabled, 1: enabled compressed, 2: enabled raw| Transmission mode: 0: video stream, >0: single images every n seconds (decimal)| Recording: 0: disabled, 1: enabled compressed, 2: enabled raw| Empty| Empty| Empty|  */
 	MAV_CMD_DO_SET_ROI=201, /* Sets the region of interest (ROI) for a sensor set or the vehicle itself. This can then be used by the vehicles control system to control the vehicle attitude and the attitude of various sensors such as cameras. |Region of intereset mode. (see MAV_ROI enum)| MISSION index/ target ID. (see MAV_ROI enum)| ROI index (allows a vehicle to manage multiple ROI's)| Empty| x the location of the fixed ROI (see MAV_FRAME)| y| z|  */
 	MAV_CMD_DO_DIGICAM_CONFIGURE=202, /* Mission command to configure an on-board camera controller system. |Modes: P, TV, AV, M, Etc| Shutter speed: Divisor number for one second| Aperture: F stop number| ISO number e.g. 80, 100, 200, Etc| Exposure type enumerator| Command Identity| Main engine cut-off time before camera trigger in seconds/10 (0 means no cut-off)|  */

autoquad/version.h

@@ -5,7 +5,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Fri Feb 26 2016"
+#define MAVLINK_BUILD_DATE "Sat Feb 27 2016"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "1.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
  

common/common.h

@@ -388,6 +388,8 @@ typedef enum MAV_CMD
 	MAV_CMD_DO_LAND_START=189, /* Mission command to perform a landing. This is used as a marker in a mission to tell the autopilot where a sequence of mission items that represents a landing starts. It may also be sent via a COMMAND_LONG to trigger a landing, in which case the nearest (geographically) landing sequence in the mission will be used. The Latitude/Longitude is optional, and may be set to 0/0 if not needed. If specified then it will be used to help find the closest landing sequence. |Empty| Empty| Empty| Empty| Latitude| Longitude| Empty|  */
 	MAV_CMD_DO_RALLY_LAND=190, /* Mission command to perform a landing from a rally point. |Break altitude (meters)| Landing speed (m/s)| Empty| Empty| Empty| Empty| Empty|  */
 	MAV_CMD_DO_GO_AROUND=191, /* Mission command to safely abort an autonmous landing. |Altitude (meters)| Empty| Empty| Empty| Empty| Empty| Empty|  */
+	MAV_CMD_DO_REPOSITION=192, /* Reposition the vehicle to a specific WGS84 global position. |Ground speed, less than 0 (-1) for default| Reserved| Reserved| Yaw heading, NaN for unchanged| Latitude (deg * 1E7)| Longitude (deg * 1E7)| Altitude (meters)|  */
+	MAV_CMD_DO_PAUSE_CONTINUE=193, /* If in a GPS controlled position mode, hold the current position or continue. |0: Pause current mission or reposition command, hold current position. 1: Continue mission. A VTOL capable vehicle should enter hover mode (multicopter and VTOL planes). A plane should loiter with the default loiter radius.| Reserved| Reserved| Reserved| Reserved| Reserved| Reserved|  */
 	MAV_CMD_DO_CONTROL_VIDEO=200, /* Control onboard camera system. |Camera ID (-1 for all)| Transmission: 0: disabled, 1: enabled compressed, 2: enabled raw| Transmission mode: 0: video stream, >0: single images every n seconds (decimal)| Recording: 0: disabled, 1: enabled compressed, 2: enabled raw| Empty| Empty| Empty|  */
 	MAV_CMD_DO_SET_ROI=201, /* Sets the region of interest (ROI) for a sensor set or the vehicle itself. This can then be used by the vehicles control system to control the vehicle attitude and the attitude of various sensors such as cameras. |Region of intereset mode. (see MAV_ROI enum)| MISSION index/ target ID. (see MAV_ROI enum)| ROI index (allows a vehicle to manage multiple ROI's)| Empty| x the location of the fixed ROI (see MAV_FRAME)| y| z|  */
 	MAV_CMD_DO_DIGICAM_CONFIGURE=202, /* Mission command to configure an on-board camera controller system. |Modes: P, TV, AV, M, Etc| Shutter speed: Divisor number for one second| Aperture: F stop number| ISO number e.g. 80, 100, 200, Etc| Exposure type enumerator| Command Identity| Main engine cut-off time before camera trigger in seconds/10 (0 means no cut-off)|  */

common/version.h

@@ -5,7 +5,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Fri Feb 26 2016"
+#define MAVLINK_BUILD_DATE "Sat Feb 27 2016"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "1.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
  

matrixpilot/matrixpilot.h

@@ -93,6 +93,8 @@ typedef enum MAV_CMD
 	MAV_CMD_DO_LAND_START=189, /* Mission command to perform a landing. This is used as a marker in a mission to tell the autopilot where a sequence of mission items that represents a landing starts. It may also be sent via a COMMAND_LONG to trigger a landing, in which case the nearest (geographically) landing sequence in the mission will be used. The Latitude/Longitude is optional, and may be set to 0/0 if not needed. If specified then it will be used to help find the closest landing sequence. |Empty| Empty| Empty| Empty| Latitude| Longitude| Empty|  */
 	MAV_CMD_DO_RALLY_LAND=190, /* Mission command to perform a landing from a rally point. |Break altitude (meters)| Landing speed (m/s)| Empty| Empty| Empty| Empty| Empty|  */
 	MAV_CMD_DO_GO_AROUND=191, /* Mission command to safely abort an autonmous landing. |Altitude (meters)| Empty| Empty| Empty| Empty| Empty| Empty|  */
+	MAV_CMD_DO_REPOSITION=192, /* Reposition the vehicle to a specific WGS84 global position. |Ground speed, less than 0 (-1) for default| Reserved| Reserved| Yaw heading, NaN for unchanged| Latitude (deg * 1E7)| Longitude (deg * 1E7)| Altitude (meters)|  */
+	MAV_CMD_DO_PAUSE_CONTINUE=193, /* If in a GPS controlled position mode, hold the current position or continue. |0: Pause current mission or reposition command, hold current position. 1: Continue mission. A VTOL capable vehicle should enter hover mode (multicopter and VTOL planes). A plane should loiter with the default loiter radius.| Reserved| Reserved| Reserved| Reserved| Reserved| Reserved|  */
 	MAV_CMD_DO_CONTROL_VIDEO=200, /* Control onboard camera system. |Camera ID (-1 for all)| Transmission: 0: disabled, 1: enabled compressed, 2: enabled raw| Transmission mode: 0: video stream, >0: single images every n seconds (decimal)| Recording: 0: disabled, 1: enabled compressed, 2: enabled raw| Empty| Empty| Empty|  */
 	MAV_CMD_DO_SET_ROI=201, /* Sets the region of interest (ROI) for a sensor set or the vehicle itself. This can then be used by the vehicles control system to control the vehicle attitude and the attitude of various sensors such as cameras. |Region of intereset mode. (see MAV_ROI enum)| MISSION index/ target ID. (see MAV_ROI enum)| ROI index (allows a vehicle to manage multiple ROI's)| Empty| x the location of the fixed ROI (see MAV_FRAME)| y| z|  */
 	MAV_CMD_DO_DIGICAM_CONFIGURE=202, /* Mission command to configure an on-board camera controller system. |Modes: P, TV, AV, M, Etc| Shutter speed: Divisor number for one second| Aperture: F stop number| ISO number e.g. 80, 100, 200, Etc| Exposure type enumerator| Command Identity| Main engine cut-off time before camera trigger in seconds/10 (0 means no cut-off)|  */

matrixpilot/version.h

@@ -5,7 +5,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Fri Feb 26 2016"
+#define MAVLINK_BUILD_DATE "Sat Feb 27 2016"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "1.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
  

message_definitions/common.xml

@@ -942,6 +942,27 @@
                     <param index="6">Empty</param>
                     <param index="7">Empty</param>
                 </entry>
+
+               <entry value="192" name="MAV_CMD_DO_REPOSITION">
+                    <description>Reposition the vehicle to a specific WGS84 global position.</description>
+                    <param index="1">Ground speed, less than 0 (-1) for default</param>
+                    <param index="2">Reserved</param>
+                    <param index="3">Reserved</param>
+                    <param index="4">Yaw heading, NaN for unchanged</param>
+                    <param index="5">Latitude (deg * 1E7)</param>
+                    <param index="6">Longitude (deg * 1E7)</param>
+                    <param index="7">Altitude (meters)</param>
+               </entry>
+               <entry value="193" name="MAV_CMD_DO_PAUSE_CONTINUE">
+                    <description>If in a GPS controlled position mode, hold the current position or continue.</description>
+                    <param index="1">0: Pause current mission or reposition command, hold current position. 1: Continue mission. A VTOL capable vehicle should enter hover mode (multicopter and VTOL planes). A plane should loiter with the default loiter radius.</param>
+                    <param index="2">Reserved</param>
+                    <param index="3">Reserved</param>
+                    <param index="4">Reserved</param>
+                    <param index="5">Reserved</param>
+                    <param index="6">Reserved</param>
+                    <param index="7">Reserved</param>
+               </entry>
                <entry value="200" name="MAV_CMD_DO_CONTROL_VIDEO">
                     <description>Control onboard camera system.</description>
                     <param index="1">Camera ID (-1 for all)</param>

minimal/version.h

@@ -5,7 +5,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Fri Feb 26 2016"
+#define MAVLINK_BUILD_DATE "Sat Feb 27 2016"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "1.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 9
  

slugs/slugs.h

@@ -76,6 +76,8 @@ typedef enum MAV_CMD
 	MAV_CMD_DO_LAND_START=189, /* Mission command to perform a landing. This is used as a marker in a mission to tell the autopilot where a sequence of mission items that represents a landing starts. It may also be sent via a COMMAND_LONG to trigger a landing, in which case the nearest (geographically) landing sequence in the mission will be used. The Latitude/Longitude is optional, and may be set to 0/0 if not needed. If specified then it will be used to help find the closest landing sequence. |Empty| Empty| Empty| Empty| Latitude| Longitude| Empty|  */
 	MAV_CMD_DO_RALLY_LAND=190, /* Mission command to perform a landing from a rally point. |Break altitude (meters)| Landing speed (m/s)| Empty| Empty| Empty| Empty| Empty|  */
 	MAV_CMD_DO_GO_AROUND=191, /* Mission command to safely abort an autonmous landing. |Altitude (meters)| Empty| Empty| Empty| Empty| Empty| Empty|  */
+	MAV_CMD_DO_REPOSITION=192, /* Reposition the vehicle to a specific WGS84 global position. |Ground speed, less than 0 (-1) for default| Reserved| Reserved| Yaw heading, NaN for unchanged| Latitude (deg * 1E7)| Longitude (deg * 1E7)| Altitude (meters)|  */
+	MAV_CMD_DO_PAUSE_CONTINUE=193, /* If in a GPS controlled position mode, hold the current position or continue. |0: Pause current mission or reposition command, hold current position. 1: Continue mission. A VTOL capable vehicle should enter hover mode (multicopter and VTOL planes). A plane should loiter with the default loiter radius.| Reserved| Reserved| Reserved| Reserved| Reserved| Reserved|  */
 	MAV_CMD_DO_CONTROL_VIDEO=200, /* Control onboard camera system. |Camera ID (-1 for all)| Transmission: 0: disabled, 1: enabled compressed, 2: enabled raw| Transmission mode: 0: video stream, >0: single images every n seconds (decimal)| Recording: 0: disabled, 1: enabled compressed, 2: enabled raw| Empty| Empty| Empty|  */
 	MAV_CMD_DO_SET_ROI=201, /* Sets the region of interest (ROI) for a sensor set or the vehicle itself. This can then be used by the vehicles control system to control the vehicle attitude and the attitude of various sensors such as cameras. |Region of intereset mode. (see MAV_ROI enum)| MISSION index/ target ID. (see MAV_ROI enum)| ROI index (allows a vehicle to manage multiple ROI's)| Empty| x the location of the fixed ROI (see MAV_FRAME)| y| z|  */
 	MAV_CMD_DO_DIGICAM_CONFIGURE=202, /* Mission command to configure an on-board camera controller system. |Modes: P, TV, AV, M, Etc| Shutter speed: Divisor number for one second| Aperture: F stop number| ISO number e.g. 80, 100, 200, Etc| Exposure type enumerator| Command Identity| Main engine cut-off time before camera trigger in seconds/10 (0 means no cut-off)|  */

slugs/version.h

@@ -5,7 +5,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Fri Feb 26 2016"
+#define MAVLINK_BUILD_DATE "Sat Feb 27 2016"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "1.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
  

test/version.h

@@ -5,7 +5,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Fri Feb 26 2016"
+#define MAVLINK_BUILD_DATE "Sat Feb 27 2016"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "1.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 179
  

ualberta/version.h

@@ -5,7 +5,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Fri Feb 26 2016"
+#define MAVLINK_BUILD_DATE "Sat Feb 27 2016"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "1.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255