autogenerated headers for rev...

autogenerated headers for rev https://github.com/mavlink/mavlink/tree/de29a2e9bffe750e87eb7004efc9803f6fba9bdf

ardupilotmega/ardupilotmega.h

@@ -66,6 +66,7 @@ typedef enum MAV_CMD
 	MAV_CMD_DO_SET_SERVO=183, /* Set a servo to a desired PWM value. |Servo number| PWM (microseconds, 1000 to 2000 typical)| Empty| Empty| Empty| Empty| Empty|  */
 	MAV_CMD_DO_REPEAT_SERVO=184, /* Cycle a between its nominal setting and a desired PWM for a desired number of cycles with a desired period. |Servo number| PWM (microseconds, 1000 to 2000 typical)| Cycle count| Cycle time (seconds)| Empty| Empty| Empty|  */
 	MAV_CMD_DO_FLIGHTTERMINATION=185, /* Terminate flight immediately |Flight termination activated if > 0.5| Empty| Empty| Empty| Empty| Empty| Empty|  */
+	MAV_CMD_DO_LAND_START=189, /* Mission command to perform a landing. This is used as a marker in a mission to tell the autopilot where a sequence of mission items that represents a landing starts. It may also be sent via a COMMAND_LONG to trigger a landing, in which case the nearest (geographically) landing sequence in the mission will be used. The Latitude/Longitude is optional, and may be set to 0/0 if not needed. If specified then it will be used to help find the closest landing sequence. |Empty| Empty| Empty| Empty| Latitude| Longitude| Empty|  */
 	MAV_CMD_DO_RALLY_LAND=190, /* Mission command to perform a landing from a rally point. |Break altitude (meters)| Landing speed (m/s)| Empty| Empty| Empty| Empty| Empty|  */
 	MAV_CMD_DO_GO_AROUND=191, /* Mission command to safely abort an autonmous landing. |Altitude (meters)| Empty| Empty| Empty| Empty| Empty| Empty|  */
 	MAV_CMD_DO_CONTROL_VIDEO=200, /* Control onboard camera system. |Camera ID (-1 for all)| Transmission: 0: disabled, 1: enabled compressed, 2: enabled raw| Transmission mode: 0: video stream, >0: single images every n seconds (decimal)| Recording: 0: disabled, 1: enabled compressed, 2: enabled raw| Empty| Empty| Empty|  */

ardupilotmega/version.h

@@ -5,7 +5,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Sat Oct  4 12:45:15 2014"
+#define MAVLINK_BUILD_DATE "Fri Oct 17 21:30:20 2014"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "1.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
  

autoquad/autoquad.h

@@ -93,6 +93,7 @@ typedef enum MAV_CMD
 	MAV_CMD_DO_SET_SERVO=183, /* Set a servo to a desired PWM value. |Servo number| PWM (microseconds, 1000 to 2000 typical)| Empty| Empty| Empty| Empty| Empty|  */
 	MAV_CMD_DO_REPEAT_SERVO=184, /* Cycle a between its nominal setting and a desired PWM for a desired number of cycles with a desired period. |Servo number| PWM (microseconds, 1000 to 2000 typical)| Cycle count| Cycle time (seconds)| Empty| Empty| Empty|  */
 	MAV_CMD_DO_FLIGHTTERMINATION=185, /* Terminate flight immediately |Flight termination activated if > 0.5| Empty| Empty| Empty| Empty| Empty| Empty|  */
+	MAV_CMD_DO_LAND_START=189, /* Mission command to perform a landing. This is used as a marker in a mission to tell the autopilot where a sequence of mission items that represents a landing starts. It may also be sent via a COMMAND_LONG to trigger a landing, in which case the nearest (geographically) landing sequence in the mission will be used. The Latitude/Longitude is optional, and may be set to 0/0 if not needed. If specified then it will be used to help find the closest landing sequence. |Empty| Empty| Empty| Empty| Latitude| Longitude| Empty|  */
 	MAV_CMD_DO_RALLY_LAND=190, /* Mission command to perform a landing from a rally point. |Break altitude (meters)| Landing speed (m/s)| Empty| Empty| Empty| Empty| Empty|  */
 	MAV_CMD_DO_GO_AROUND=191, /* Mission command to safely abort an autonmous landing. |Altitude (meters)| Empty| Empty| Empty| Empty| Empty| Empty|  */
 	MAV_CMD_DO_CONTROL_VIDEO=200, /* Control onboard camera system. |Camera ID (-1 for all)| Transmission: 0: disabled, 1: enabled compressed, 2: enabled raw| Transmission mode: 0: video stream, >0: single images every n seconds (decimal)| Recording: 0: disabled, 1: enabled compressed, 2: enabled raw| Empty| Empty| Empty|  */

autoquad/version.h

@@ -5,7 +5,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Sat Oct  4 12:45:26 2014"
+#define MAVLINK_BUILD_DATE "Fri Oct 17 21:30:27 2014"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "1.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
  

common/common.h

@@ -347,6 +347,7 @@ typedef enum MAV_CMD
 	MAV_CMD_DO_SET_SERVO=183, /* Set a servo to a desired PWM value. |Servo number| PWM (microseconds, 1000 to 2000 typical)| Empty| Empty| Empty| Empty| Empty|  */
 	MAV_CMD_DO_REPEAT_SERVO=184, /* Cycle a between its nominal setting and a desired PWM for a desired number of cycles with a desired period. |Servo number| PWM (microseconds, 1000 to 2000 typical)| Cycle count| Cycle time (seconds)| Empty| Empty| Empty|  */
 	MAV_CMD_DO_FLIGHTTERMINATION=185, /* Terminate flight immediately |Flight termination activated if > 0.5| Empty| Empty| Empty| Empty| Empty| Empty|  */
+	MAV_CMD_DO_LAND_START=189, /* Mission command to perform a landing. This is used as a marker in a mission to tell the autopilot where a sequence of mission items that represents a landing starts. It may also be sent via a COMMAND_LONG to trigger a landing, in which case the nearest (geographically) landing sequence in the mission will be used. The Latitude/Longitude is optional, and may be set to 0/0 if not needed. If specified then it will be used to help find the closest landing sequence. |Empty| Empty| Empty| Empty| Latitude| Longitude| Empty|  */
 	MAV_CMD_DO_RALLY_LAND=190, /* Mission command to perform a landing from a rally point. |Break altitude (meters)| Landing speed (m/s)| Empty| Empty| Empty| Empty| Empty|  */
 	MAV_CMD_DO_GO_AROUND=191, /* Mission command to safely abort an autonmous landing. |Altitude (meters)| Empty| Empty| Empty| Empty| Empty| Empty|  */
 	MAV_CMD_DO_CONTROL_VIDEO=200, /* Control onboard camera system. |Camera ID (-1 for all)| Transmission: 0: disabled, 1: enabled compressed, 2: enabled raw| Transmission mode: 0: video stream, >0: single images every n seconds (decimal)| Recording: 0: disabled, 1: enabled compressed, 2: enabled raw| Empty| Empty| Empty|  */

common/version.h

@@ -5,7 +5,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Sat Oct  4 12:46:19 2014"
+#define MAVLINK_BUILD_DATE "Fri Oct 17 21:31:24 2014"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "1.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
  

matrixpilot/matrixpilot.h

@@ -83,6 +83,7 @@ typedef enum MAV_CMD
 	MAV_CMD_DO_SET_SERVO=183, /* Set a servo to a desired PWM value. |Servo number| PWM (microseconds, 1000 to 2000 typical)| Empty| Empty| Empty| Empty| Empty|  */
 	MAV_CMD_DO_REPEAT_SERVO=184, /* Cycle a between its nominal setting and a desired PWM for a desired number of cycles with a desired period. |Servo number| PWM (microseconds, 1000 to 2000 typical)| Cycle count| Cycle time (seconds)| Empty| Empty| Empty|  */
 	MAV_CMD_DO_FLIGHTTERMINATION=185, /* Terminate flight immediately |Flight termination activated if > 0.5| Empty| Empty| Empty| Empty| Empty| Empty|  */
+	MAV_CMD_DO_LAND_START=189, /* Mission command to perform a landing. This is used as a marker in a mission to tell the autopilot where a sequence of mission items that represents a landing starts. It may also be sent via a COMMAND_LONG to trigger a landing, in which case the nearest (geographically) landing sequence in the mission will be used. The Latitude/Longitude is optional, and may be set to 0/0 if not needed. If specified then it will be used to help find the closest landing sequence. |Empty| Empty| Empty| Empty| Latitude| Longitude| Empty|  */
 	MAV_CMD_DO_RALLY_LAND=190, /* Mission command to perform a landing from a rally point. |Break altitude (meters)| Landing speed (m/s)| Empty| Empty| Empty| Empty| Empty|  */
 	MAV_CMD_DO_GO_AROUND=191, /* Mission command to safely abort an autonmous landing. |Altitude (meters)| Empty| Empty| Empty| Empty| Empty| Empty|  */
 	MAV_CMD_DO_CONTROL_VIDEO=200, /* Control onboard camera system. |Camera ID (-1 for all)| Transmission: 0: disabled, 1: enabled compressed, 2: enabled raw| Transmission mode: 0: video stream, >0: single images every n seconds (decimal)| Recording: 0: disabled, 1: enabled compressed, 2: enabled raw| Empty| Empty| Empty|  */

matrixpilot/version.h

@@ -5,7 +5,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Sat Oct  4 12:45:33 2014"
+#define MAVLINK_BUILD_DATE "Fri Oct 17 21:30:35 2014"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "1.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
  

minimal/version.h

@@ -5,7 +5,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Sat Oct  4 12:45:42 2014"
+#define MAVLINK_BUILD_DATE "Fri Oct 17 21:30:43 2014"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "1.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 9
  

pixhawk/pixhawk.h

@@ -78,6 +78,7 @@ typedef enum MAV_CMD
 	MAV_CMD_DO_SET_SERVO=183, /* Set a servo to a desired PWM value. |Servo number| PWM (microseconds, 1000 to 2000 typical)| Empty| Empty| Empty| Empty| Empty|  */
 	MAV_CMD_DO_REPEAT_SERVO=184, /* Cycle a between its nominal setting and a desired PWM for a desired number of cycles with a desired period. |Servo number| PWM (microseconds, 1000 to 2000 typical)| Cycle count| Cycle time (seconds)| Empty| Empty| Empty|  */
 	MAV_CMD_DO_FLIGHTTERMINATION=185, /* Terminate flight immediately |Flight termination activated if > 0.5| Empty| Empty| Empty| Empty| Empty| Empty|  */
+	MAV_CMD_DO_LAND_START=189, /* Mission command to perform a landing. This is used as a marker in a mission to tell the autopilot where a sequence of mission items that represents a landing starts. It may also be sent via a COMMAND_LONG to trigger a landing, in which case the nearest (geographically) landing sequence in the mission will be used. The Latitude/Longitude is optional, and may be set to 0/0 if not needed. If specified then it will be used to help find the closest landing sequence. |Empty| Empty| Empty| Empty| Latitude| Longitude| Empty|  */
 	MAV_CMD_DO_RALLY_LAND=190, /* Mission command to perform a landing from a rally point. |Break altitude (meters)| Landing speed (m/s)| Empty| Empty| Empty| Empty| Empty|  */
 	MAV_CMD_DO_GO_AROUND=191, /* Mission command to safely abort an autonmous landing. |Altitude (meters)| Empty| Empty| Empty| Empty| Empty| Empty|  */
 	MAV_CMD_DO_CONTROL_VIDEO=200, /* Control onboard camera system. |Camera ID (-1 for all)| Transmission: 0: disabled, 1: enabled compressed, 2: enabled raw| Transmission mode: 0: video stream, >0: single images every n seconds (decimal)| Recording: 0: disabled, 1: enabled compressed, 2: enabled raw| Empty| Empty| Empty|  */

pixhawk/version.h

@@ -5,7 +5,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Sat Oct  4 12:45:43 2014"
+#define MAVLINK_BUILD_DATE "Fri Oct 17 21:30:44 2014"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "1.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
  

sensesoar/version.h

@@ -5,7 +5,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Sat Oct  4 12:45:51 2014"
+#define MAVLINK_BUILD_DATE "Fri Oct 17 21:30:54 2014"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "1.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
  

slugs/slugs.h

@@ -66,6 +66,7 @@ typedef enum MAV_CMD
 	MAV_CMD_DO_SET_SERVO=183, /* Set a servo to a desired PWM value. |Servo number| PWM (microseconds, 1000 to 2000 typical)| Empty| Empty| Empty| Empty| Empty|  */
 	MAV_CMD_DO_REPEAT_SERVO=184, /* Cycle a between its nominal setting and a desired PWM for a desired number of cycles with a desired period. |Servo number| PWM (microseconds, 1000 to 2000 typical)| Cycle count| Cycle time (seconds)| Empty| Empty| Empty|  */
 	MAV_CMD_DO_FLIGHTTERMINATION=185, /* Terminate flight immediately |Flight termination activated if > 0.5| Empty| Empty| Empty| Empty| Empty| Empty|  */
+	MAV_CMD_DO_LAND_START=189, /* Mission command to perform a landing. This is used as a marker in a mission to tell the autopilot where a sequence of mission items that represents a landing starts. It may also be sent via a COMMAND_LONG to trigger a landing, in which case the nearest (geographically) landing sequence in the mission will be used. The Latitude/Longitude is optional, and may be set to 0/0 if not needed. If specified then it will be used to help find the closest landing sequence. |Empty| Empty| Empty| Empty| Latitude| Longitude| Empty|  */
 	MAV_CMD_DO_RALLY_LAND=190, /* Mission command to perform a landing from a rally point. |Break altitude (meters)| Landing speed (m/s)| Empty| Empty| Empty| Empty| Empty|  */
 	MAV_CMD_DO_GO_AROUND=191, /* Mission command to safely abort an autonmous landing. |Altitude (meters)| Empty| Empty| Empty| Empty| Empty| Empty|  */
 	MAV_CMD_DO_CONTROL_VIDEO=200, /* Control onboard camera system. |Camera ID (-1 for all)| Transmission: 0: disabled, 1: enabled compressed, 2: enabled raw| Transmission mode: 0: video stream, >0: single images every n seconds (decimal)| Recording: 0: disabled, 1: enabled compressed, 2: enabled raw| Empty| Empty| Empty|  */

slugs/version.h

@@ -5,7 +5,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Sat Oct  4 12:45:58 2014"
+#define MAVLINK_BUILD_DATE "Fri Oct 17 21:31:02 2014"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "1.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255
  

test/version.h

@@ -5,7 +5,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Sat Oct  4 12:46:05 2014"
+#define MAVLINK_BUILD_DATE "Fri Oct 17 21:31:09 2014"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "1.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 179
  

ualberta/version.h

@@ -5,7 +5,7 @@
 #ifndef MAVLINK_VERSION_H
 #define MAVLINK_VERSION_H
 
-#define MAVLINK_BUILD_DATE "Sat Oct  4 12:46:08 2014"
+#define MAVLINK_BUILD_DATE "Fri Oct 17 21:31:12 2014"
 #define MAVLINK_WIRE_PROTOCOL_VERSION "1.0"
 #define MAVLINK_MAX_DIALECT_PAYLOAD_SIZE 255