scsi: hisi_sas: fix the issue of setting linkrate register

It is not right to set the register PROG_PHY_LINK_RATE while PHY is still
enabled. So if we want to change PHY linkrate, we need to disable PHY before
setting the register PROG_PHY_LINK_RATE, and then start-up PHY. This patch
is to fix this issue.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

drivers/scsi/hisi_sas/hisi_sas_v1_hw.c

@@ -881,10 +881,11 @@ static void phy_set_linkrate_v1_hw(struct hisi_hba *hisi_hba, int phy_no,
 	prog_phy_link_rate &= ~0xff;
 	prog_phy_link_rate |= rate_mask;
 
+	disable_phy_v1_hw(hisi_hba, phy_no);
+	msleep(100);
 	hisi_sas_phy_write32(hisi_hba, phy_no, PROG_PHY_LINK_RATE,
 			prog_phy_link_rate);
-
-	phy_hard_reset_v1_hw(hisi_hba, phy_no);
+	start_phy_v1_hw(hisi_hba, phy_no);
 }
 
 static int get_wideport_bitmap_v1_hw(struct hisi_hba *hisi_hba, int port_id)

drivers/scsi/hisi_sas/hisi_sas_v2_hw.c

@@ -1611,10 +1611,11 @@ static void phy_set_linkrate_v2_hw(struct hisi_hba *hisi_hba, int phy_no,
 	prog_phy_link_rate &= ~0xff;
 	prog_phy_link_rate |= rate_mask;
 
+	disable_phy_v2_hw(hisi_hba, phy_no);
+	msleep(100);
 	hisi_sas_phy_write32(hisi_hba, phy_no, PROG_PHY_LINK_RATE,
 			prog_phy_link_rate);
-
-	phy_hard_reset_v2_hw(hisi_hba, phy_no);
+	start_phy_v2_hw(hisi_hba, phy_no);
 }
 
 static int get_wideport_bitmap_v2_hw(struct hisi_hba *hisi_hba, int port_id)

drivers/scsi/hisi_sas/hisi_sas_v3_hw.c

@@ -1862,10 +1862,11 @@ static void phy_set_linkrate_v3_hw(struct hisi_hba *hisi_hba, int phy_no,
 	prog_phy_link_rate &= ~0xff;
 	prog_phy_link_rate |= rate_mask;
 
+	disable_phy_v3_hw(hisi_hba, phy_no);
+	msleep(100);
 	hisi_sas_phy_write32(hisi_hba, phy_no, PROG_PHY_LINK_RATE,
 			prog_phy_link_rate);
-
-	phy_hard_reset_v3_hw(hisi_hba, phy_no);
+	start_phy_v3_hw(hisi_hba, phy_no);
 }
 
 static void interrupt_disable_v3_hw(struct hisi_hba *hisi_hba)