Commit 01f2901a authored by Tang Yuantian's avatar Tang Yuantian Committed by Tejun Heo

ahci: qoriq: report error when ecc register address is missing in dts

For ls1021a, and armv8 chasis 2 socs, sata ecc must be disabled.
If ecc register is not found in sata node in dts, report error.

This is a chip erratum described as bellow:
The Read DMA operations get early termination indication from the
controller. This issue is observed as CRC error in the status registers.
The issue is due to address collision at address 0 in the dual port
memory. The read is a dummy read to flush out the header, but due to
collision the controller logs the mbit error reported by the ECC check
logic. This results in the early termination of the Read DMA operation
by the controller. The issue happens to all the interface
speeds(GEN1/2/3) for all the products.

Workaround:
Disable ECC feature on those platforms.
Signed-off-by: default avatarTang Yuantian <yuantian.tang@nxp.com>
Signed-off-by: default avatarTejun Heo <tj@kernel.org>
parent 386dc3b8
......@@ -46,7 +46,7 @@
#define LS1021A_AXICC_ADDR 0xC0
#define SATA_ECC_DISABLE 0x00020000
#define LS1046A_SATA_ECC_DIS 0x80000000
#define ECC_DIS_ARMV8_CH2 0x80000000
enum ahci_qoriq_type {
AHCI_LS1021A,
......@@ -158,6 +158,8 @@ static int ahci_qoriq_phy_init(struct ahci_host_priv *hpriv)
switch (qpriv->type) {
case AHCI_LS1021A:
if (!qpriv->ecc_addr)
return -EINVAL;
writel(SATA_ECC_DISABLE, qpriv->ecc_addr);
writel(AHCI_PORT_PHY_1_CFG, reg_base + PORT_PHY1);
writel(LS1021A_PORT_PHY2, reg_base + PORT_PHY2);
......@@ -171,6 +173,9 @@ static int ahci_qoriq_phy_init(struct ahci_host_priv *hpriv)
break;
case AHCI_LS1043A:
if (!qpriv->ecc_addr)
return -EINVAL;
writel(ECC_DIS_ARMV8_CH2, qpriv->ecc_addr);
writel(AHCI_PORT_PHY_1_CFG, reg_base + PORT_PHY1);
writel(AHCI_PORT_TRANS_CFG, reg_base + PORT_TRANS);
if (qpriv->is_dmacoherent)
......@@ -185,7 +190,9 @@ static int ahci_qoriq_phy_init(struct ahci_host_priv *hpriv)
break;
case AHCI_LS1046A:
writel(LS1046A_SATA_ECC_DIS, qpriv->ecc_addr);
if (!qpriv->ecc_addr)
return -EINVAL;
writel(ECC_DIS_ARMV8_CH2, qpriv->ecc_addr);
writel(AHCI_PORT_PHY_1_CFG, reg_base + PORT_PHY1);
writel(AHCI_PORT_TRANS_CFG, reg_base + PORT_TRANS);
if (qpriv->is_dmacoherent)
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment