Merge branch 'net-mvpp2-fixes-and-improvements'

Antoine Tenart says:

====================
net: mvpp2: fixes and improvements

This series aims to improve the Marvell PPv2 driver and to fix various
issues we encountered while testing the ports in many different
configurations. The series is based on top of Russell PPv2 phylink
rework and improvement.

I'm not sending a v2 of the previous fixes series as half the patches
are not the same and lots of development happened in between.

While this series contains fixes, it's sent to net-next as it is based
on top of Russell patches that were merged into net-next. I'm also
aiming at net-next as the series reworks critical paths of the PPv2
driver, such as the reset handling of various blocks, to let more weeks
for users to tests and for possible fixes to be sent before it lands
into a stable kernel version.

The series is divided into three parts:

- Patches 1 to 3 are cosmetic changes, sent alongside the series, as I
  saw these small issues while working on this.

- Patches 5 to 8 are fixing (or improving) individual issues that we
  found while testing PPv2.1 and PPv2.2 ports while using various
  interfaces.

  Notable fixes are we support back RGMII interfaces (on both PPv2.1 and
  PPv2.2), as their support was broken by previous patches. We also
  reworked the RXQ computation as the RXQ assignment was not checking
  the maximum number of RXQ available, and was broken for PPv2.1.

- As discussed in a previous fixes series, patches 9 to 15 rework the
  way blocks are set in reset in the PPv2 engine (plus related changes).

  There are four blocks we want to control the reset status: two MAC
  (GMAC and XLG MAC) and two PCS (MPCS and XPCS). The XLG MAC is used
  for 10G connexions and uses the MPCS or the XPCS depending on the mode
  used (10GKR / XAUI / RXAUI) and the GMAC is used for the other modes.

  The idea is to set all blocks in reset by default, and when not used,
  and to de-assert the reset only when a block is used. There are four
  cases to take in account:

  1. Boot time: all four blocks should be put in reset, as we do not
     know their initial state (configured by the firmware/bootloader).

  2. Link up: only the blocks used by a given mode should be put out of
     reset (eg. 10GKR uses the XLG MAC and the MPCS).

  3. Mode reconfiguration: some ports may support mode reconfiguration,
     and switching between the GMAC and the XLG MAC (or between the two
     PCS). All blocks should be put in reset, and only the one used
     should be put out of reset.

  4. Link down: all four blocks are put in reset.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/marvell/mvpp2/mvpp2.h

@@ -389,7 +389,7 @@
 #define     MVPP2_GMAC_IN_BAND_AUTONEG		BIT(2)
 #define     MVPP2_GMAC_IN_BAND_AUTONEG_BYPASS	BIT(3)
 #define     MVPP2_GMAC_IN_BAND_RESTART_AN	BIT(4)
-#define     MVPP2_GMAC_CONFIG_MII_SPEED	BIT(5)
+#define     MVPP2_GMAC_CONFIG_MII_SPEED		BIT(5)
 #define     MVPP2_GMAC_CONFIG_GMII_SPEED	BIT(6)
 #define     MVPP2_GMAC_AN_SPEED_EN		BIT(7)
 #define     MVPP2_GMAC_FC_ADV_EN		BIT(9)
@@ -430,6 +430,8 @@
 #define MVPP22_XLG_CTRL0_REG			0x100
 #define     MVPP22_XLG_CTRL0_PORT_EN		BIT(0)
 #define     MVPP22_XLG_CTRL0_MAC_RESET_DIS	BIT(1)
+#define     MVPP22_XLG_CTRL0_FORCE_LINK_DOWN	BIT(2)
+#define     MVPP22_XLG_CTRL0_FORCE_LINK_PASS	BIT(3)
 #define     MVPP22_XLG_CTRL0_RX_FLOW_CTRL_EN	BIT(7)
 #define     MVPP22_XLG_CTRL0_TX_FLOW_CTRL_EN	BIT(8)
 #define     MVPP22_XLG_CTRL0_MIB_CNT_DIS	BIT(14)
@@ -481,6 +483,7 @@
 /* XPCS registers. PPv2.2 only */
 #define MVPP22_XPCS_BASE(port)			(0x7400 + (port) * 0x1000)
 #define MVPP22_XPCS_CFG0			0x0
+#define     MVPP22_XPCS_CFG0_RESET_DIS		BIT(0)
 #define     MVPP22_XPCS_CFG0_PCS_MODE(n)	((n) << 3)
 #define     MVPP22_XPCS_CFG0_ACTIVE_LANE(n)	((n) << 5)
 
@@ -549,8 +552,8 @@
 #define MVPP2_MAX_TSO_SEGS		300
 #define MVPP2_MAX_SKB_DESCS		(MVPP2_MAX_TSO_SEGS * 2 + MAX_SKB_FRAGS)
 
-/* Dfault number of RXQs in use */
-#define MVPP2_DEFAULT_RXQ		1
+/* Max number of RXQs per port */
+#define MVPP2_PORT_MAX_RXQ		32
 
 /* Max number of Rx descriptors */
 #define MVPP2_MAX_RXD_MAX		1024
@@ -803,7 +806,7 @@ struct mvpp2_port {
 	u8 id;
 
 	/* Index of the port from the "group of ports" complex point
-	 * of view
+	 * of view. This is specific to PPv2.2.
 	 */
 	int gop_id;