Merge tag 'omap-for-v4.17/dt-sdhci-signed' of...

Merge tag 'omap-for-v4.17/dt-sdhci-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt

Pull "Device tree changes for dra7 sdhci for v4.17" from Tony Lindgren:

This series from Sekhar Nori and Kishon Vijay Abraham I adds
sdhci related nodes for dra7. To support higher transfer speeds,
the iodelay pinmux controller needs to be also configured.

Note that as these changes need SDHCI_OMAP to be enabled to avoid
breaking booting for various systems, these changes are based on
two defconfig changes to enable SDHCI_OMAP in the defconfig files.

* tag 'omap-for-v4.17/dt-sdhci-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: am57xx-idk: Select pull down for mmc1_clk line in default mode
  ARM: dts: dra71-evm: Select pull down for mmc1_clk line in default mode
  ARM: dts: dra71-evm: Correct evm_sd regulator max voltage
  ARM: dts: dra76-evm: Add "vqmmc-supply" property for mmc2
  ARM: dts: am57xx-idk: Add "vqmmc-supply" property for mmc2
  ARM: dts: dra7-evm: Add "vqmmc-supply" property for mmc2
  ARM: dts: dra7-evm: Remove mmc specific pinmux
  ARM: dts: am57xx-beagle-x15: Add "vqmmc-supply" property for mmc2
  ARM: dts: dra76-evm: Add pinctrl data for higher speed MMC/SD modes
  ARM: dts: dra76-evm: Shift to using common IOdelay data
  ARM: dts: dra76x: Create a common file with MMC/SD IOdelay data
  ARM: omap2plus_defconfig: Enable CONFIG_MMC_SDHCI_OMAP
  ARM: multi_v7_defconfig: Enable CONFIG_MMC_SDHCI_OMAP

arch/arm/boot/dts/am571x-idk.dts

@@ -10,8 +10,8 @@
 #include "dra72x.dtsi"
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interrupt-controller/irq.h>
-#include "am57xx-idk-common.dtsi"
 #include "dra72x-mmc-iodelay.dtsi"
+#include "am57xx-idk-common.dtsi"
 
 / {
 	model = "TI AM5718 IDK";

arch/arm/boot/dts/am572x-idk.dts

@@ -9,9 +9,8 @@
 /dts-v1/;
 
 #include "dra74x.dtsi"
-#include "am572x-idk-common.dtsi"
-#include "am57xx-idk-common.dtsi"
 #include "dra74x-mmc-iodelay.dtsi"
+#include "am572x-idk-common.dtsi"
 
 / {
 	model = "TI AM5728 IDK";

arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi

@@ -442,6 +442,7 @@ &mmc2 {
 	pinctrl-0 = <&mmc2_pins_default>;
 
 	vmmc-supply = <&vdd_3v3>;
+	vqmmc-supply = <&vdd_3v3>;
 	bus-width = <8>;
 	ti,non-removable;
 	cap-mmc-dual-data-rate;

arch/arm/boot/dts/am57xx-idk-common.dtsi

@@ -115,6 +115,17 @@ DRA7XX_CORE_IOPAD(0x37d0, MUX_MODE15 | PULL_UP)	/* dcan1_tx.off */
 			DRA7XX_CORE_IOPAD(0x37d4, MUX_MODE15 | PULL_UP)	/* dcan1_rx.off */
 		>;
 	};
+
+	mmc1_pins_default: mmc1_pins_default {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mmc1_clk.clk */
+			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */
+			DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */
+			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */
+			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */
+			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */
+		>;
+	};
 };
 
 &i2c1 {
@@ -410,6 +421,7 @@ &mmc1 {
 &mmc2 {
 	status = "okay";
 	vmmc-supply = <&v3_3d>;
+	vqmmc-supply = <&v3_3d>;
 	bus-width = <8>;
 	ti,non-removable;
 	max-frequency = <96000000>;

arch/arm/boot/dts/dra7-evm.dts

@@ -87,33 +87,6 @@ DRA7XX_CORE_IOPAD(0x37d0, MUX_MODE15 | PULL_UP)	/* dcan1_tx.off */
 			DRA7XX_CORE_IOPAD(0x3818, MUX_MODE15 | PULL_UP)	/* wakeup0.off */
 		>;
 	};
-
-	mmc1_pins_default: mmc1_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x376c, PIN_INPUT | MUX_MODE14)	/* mmc1sdcd.gpio219 */
-			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */
-			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */
-			DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */
-			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */
-			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */
-			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */
-		>;
-	};
-
-	mmc2_pins_default: mmc2_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */
-			DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
-			DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */
-			DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */
-			DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */
-			DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */
-			DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */
-			DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */
-			DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */
-			DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
-		>;
-	};
 };
 
 &i2c1 {
@@ -350,6 +323,7 @@ &mmc1 {
 &mmc2 {
 	status = "okay";
 	vmmc-supply = <&evm_1v8_sw>;
+	vqmmc-supply = <&evm_1v8_sw>;
 	bus-width = <8>;
 	pinctrl-names = "default", "hs", "ddr_1_8v-rev11", "ddr_1_8v", "hs200_1_8v-rev11", "hs200_1_8v";
 	pinctrl-0 = <&mmc2_pins_default>;

arch/arm/boot/dts/dra71-evm.dts

@@ -24,13 +24,13 @@ vpo_sd_1v8_3v3: gpio-regulator-TPS74801 {
 
 		regulator-name = "vddshv8";
 		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <3000000>;
+		regulator-max-microvolt = <3300000>;
 		regulator-boot-on;
 		vin-supply = <&evm_5v0>;
 
 		gpios = <&gpio7 11 GPIO_ACTIVE_HIGH>;
 		states = <1800000 0x0
-			  3000000 0x1>;
+			  3300000 0x1>;
 	};
 
 	evm_1v8_sw: fixedregulator-evm_1v8 {
@@ -50,6 +50,19 @@ poweroff: gpio-poweroff {
 	};
 };
 
+&dra7_pmx_core {
+	mmc1_pins_default: mmc1_pins_default {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mmc1_clk.clk */
+			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */
+			DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */
+			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */
+			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */
+			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */
+		>;
+	};
+};
+
 &i2c1 {
 	status = "okay";
 	clock-frequency = <400000>;

arch/arm/boot/dts/dra76-evm.dts

@@ -9,6 +9,7 @@
 
 #include "dra76x.dtsi"
 #include "dra7-evm-common.dtsi"
+#include "dra76x-mmc-iodelay.dtsi"
 #include <dt-bindings/net/ti-dp83867.h>
 
 / {
@@ -100,46 +101,6 @@ aic_dvdd: fixedregulator-aic_dvdd {
 	};
 };
 
-&dra7_pmx_core {
-	mmc1_pins_default: mmc1_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x376c, PIN_INPUT | MUX_MODE14)	/* mmc1sdcd.gpio219 */
-			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */
-			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */
-			DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */
-			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */
-			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */
-			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */
-		>;
-	};
-
-	mmc1_pins_sdr12: pinmux_mmc1_sdr12_pins {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_clk.clk */
-			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_cmd.cmd */
-			DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat0.dat0 */
-			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat1.dat1 */
-			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat2.dat2 */
-			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat3.dat3 */
-		>;
-	};
-
-	mmc2_pins_default: mmc2_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */
-			DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
-			DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */
-			DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */
-			DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */
-			DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */
-			DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */
-			DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */
-			DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */
-			DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
-		>;
-	};
-};
-
 &i2c1 {
 	status = "okay";
 	clock-frequency = <400000>;
@@ -353,16 +314,21 @@ &mmc1 {
 	 * is always hardwired.
 	 */
 	cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>;
-	pinctrl-names = "default";
+	pinctrl-names = "default", "hs";
 	pinctrl-0 = <&mmc1_pins_default>;
+	pinctrl-1 = <&mmc1_pins_hs>;
 };
 
 &mmc2 {
 	status = "okay";
 	vmmc-supply = <&vio_1v8>;
+	vqmmc-supply = <&vio_1v8>;
 	bus-width = <8>;
-	pinctrl-names = "default";
+	pinctrl-names = "default", "hs", "ddr_1_8v", "hs200_1_8v";
 	pinctrl-0 = <&mmc2_pins_default>;
+	pinctrl-1 = <&mmc2_pins_default>;
+	pinctrl-2 = <&mmc2_pins_default>;
+	pinctrl-3 = <&mmc2_pins_hs200 &mmc2_iodelay_hs200_conf>;
 };
 
 /* No RTC on this device */

arch/arm/configs/multi_v7_defconfig

@@ -751,6 +751,7 @@ CONFIG_MMC_DW_ROCKCHIP=y
 CONFIG_MMC_SH_MMCIF=y
 CONFIG_MMC_SUNXI=y
 CONFIG_MMC_BCM2835=y
+CONFIG_MMC_SDHCI_OMAP=y
 CONFIG_NEW_LEDS=y
 CONFIG_LEDS_CLASS=y
 CONFIG_LEDS_CLASS_FLASH=m

arch/arm/configs/omap2plus_defconfig

@@ -431,8 +431,11 @@ CONFIG_USB_ZERO=m
 CONFIG_USB_G_NOKIA=m
 CONFIG_MMC=y
 CONFIG_SDIO_UART=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_PLTFM=y
 CONFIG_MMC_OMAP=y
 CONFIG_MMC_OMAP_HS=y
+CONFIG_MMC_SDHCI_OMAP=y
 CONFIG_NEW_LEDS=y
 CONFIG_LEDS_CLASS=m
 CONFIG_LEDS_CPCAP=m