Documentation: usb: fix wrong documentation paths

Fixes wrong spelled "pinctrl-bindings.txt" and "qcom-dwc3-usb-phy.txt"
file names as also wrong specified "mt8173-mtu3.txt" file name.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Documentation/devicetree/bindings/usb/dwc3-st.txt

@@ -20,10 +20,10 @@ See: Documentation/devicetree/bindings/reset/reset.txt
    with 'reg' property
 
  - pinctl-names	: A pinctrl state named "default" must be defined
-See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt
+See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
 
  - pinctrl-0	: Pin control group
-See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt
+See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
 
  - ranges	: allows valid 1:1 translation between child's address space and
 		  parent's address space

Documentation/devicetree/bindings/usb/ehci-st.txt

@@ -7,7 +7,7 @@ Required properties:
  - interrupts		: one EHCI interrupt should be described here
  - pinctrl-names	: a pinctrl state named "default" must be defined
  - pinctrl-0		: phandle referencing pin configuration of the USB controller
-See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt
+See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
  - clocks		: phandle list of usb clocks
  - clock-names		: should be "ic" for interconnect clock and "clk48"
 See: Documentation/devicetree/bindings/clock/clock-bindings.txt

Documentation/devicetree/bindings/usb/mt8173-mtu3.txt

@@ -30,7 +30,7 @@ Optional properties:
 	"id_float" and "id_ground" are optinal which depends on
 	"mediatek,enable-manual-drd"
  - pinctrl-0 : pin control group
-	See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt
+	See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
 
  - maximum-speed : valid arguments are "super-speed", "high-speed" and
 	"full-speed"; refer to usb/generic.txt

Documentation/devicetree/bindings/usb/mt8173-xhci.txt

@@ -37,7 +37,7 @@ Optional properties:
  - usb3-lpm-capable : supports USB3.0 LPM
  - pinctrl-names : a pinctrl state named "default" must be defined
  - pinctrl-0 : pin control group
-	See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt
+	See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
 
 Example:
 usb30: usb@11270000 {
@@ -67,7 +67,7 @@ usb30: usb@11270000 {
 
 In the case, xhci is added as subnode to mtu3. An example and the DT binding
 details of mtu3 can be found in:
-Documentation/devicetree/bindings/usb/mtu3.txt
+Documentation/devicetree/bindings/usb/mt8173-mtu3.txt
 
 Required properties:
  - compatible : should contain "mediatek,mt8173-xhci"

Documentation/devicetree/bindings/usb/qcom,dwc3.txt

@@ -18,7 +18,7 @@ A child node must exist to represent the core DWC3 IP block. The name of
 the node is not important. The content of the node is defined in dwc3.txt.
 
 Phy documentation is provided in the following places:
-Documentation/devicetree/bindings/phy/qcom,dwc3-usb-phy.txt
+Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt
 
 Example device nodes: