Commit 090ffa9d authored by David Brownell's avatar David Brownell Committed by Greg Kroah-Hartman

[PATCH] USB: usbnet (9/9) module for pl2301/2302 cables

This wraps up the conversion of the "usbnet" driver structure, by
moving the Prolific PL-2201/2302 minidriver to a module of its own.
It also includes some minor cleanups to the remaining "usbnet" file,
notably removing that long changelog at the top.

Minor historical note:  Linux 2.2 first called the driver for
this hardware "plusb".
Signed-off-by: default avatarDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@suse.de>
parent 64e04910
...@@ -99,7 +99,7 @@ config USB_USBNET ...@@ -99,7 +99,7 @@ config USB_USBNET
with "minidrivers" built around a common network driver core with "minidrivers" built around a common network driver core
that supports deep queues for efficient transfers. (This gives that supports deep queues for efficient transfers. (This gives
better performance with small packets and at high speeds). better performance with small packets and at high speeds).
The USB host runs "usbnet", and the other end of the link might be: The USB host runs "usbnet", and the other end of the link might be:
- Another USB host, when using USB "network" or "data transfer" - Another USB host, when using USB "network" or "data transfer"
...@@ -125,20 +125,6 @@ config USB_USBNET ...@@ -125,20 +125,6 @@ config USB_USBNET
To compile this driver as a module, choose M here: the To compile this driver as a module, choose M here: the
module will be called usbnet. module will be called usbnet.
comment "USB Host-to-Host Cables"
depends on USB_USBNET
config USB_PL2301
boolean "Prolific PL-2301/2302 based cables"
default y
# handshake/init/reset problems, from original 'plusb' driver
depends on USB_USBNET && EXPERIMENTAL
help
Choose this option if you're using a host-to-host cable
with one of these chips.
comment "Drivers built using the usbnet core"
config USB_NET_AX8817X config USB_NET_AX8817X
tristate "ASIX AX88xxx Based USB 2.0 Ethernet Adapters" tristate "ASIX AX88xxx Based USB 2.0 Ethernet Adapters"
depends on USB_USBNET && NET_ETHERNET depends on USB_USBNET && NET_ETHERNET
...@@ -212,6 +198,15 @@ config USB_NET_NET1080 ...@@ -212,6 +198,15 @@ config USB_NET_NET1080
on this design: one NetChip 1080 chip and supporting logic, on this design: one NetChip 1080 chip and supporting logic,
optionally with LEDs that indicate traffic optionally with LEDs that indicate traffic
config USB_NET_PLUSB
tristate "Prolific PL-2301/2302 based cables"
# if the handshake/init/reset problems, from original 'plusb',
# are ever resolved ... then remove "experimental"
depends on USB_USBNET && EXPERIMENTAL
help
Choose this option if you're using a host-to-host cable
with one of these chips.
config USB_NET_RNDIS_HOST config USB_NET_RNDIS_HOST
tristate "Host for RNDIS devices (EXPERIMENTAL)" tristate "Host for RNDIS devices (EXPERIMENTAL)"
depends on USB_USBNET && EXPERIMENTAL depends on USB_USBNET && EXPERIMENTAL
......
...@@ -10,6 +10,7 @@ obj-$(CONFIG_USB_NET_AX8817X) += asix.o ...@@ -10,6 +10,7 @@ obj-$(CONFIG_USB_NET_AX8817X) += asix.o
obj-$(CONFIG_USB_NET_CDCETHER) += cdc_ether.o obj-$(CONFIG_USB_NET_CDCETHER) += cdc_ether.o
obj-$(CONFIG_USB_NET_GL620A) += gl620a.o obj-$(CONFIG_USB_NET_GL620A) += gl620a.o
obj-$(CONFIG_USB_NET_NET1080) += net1080.o obj-$(CONFIG_USB_NET_NET1080) += net1080.o
obj-$(CONFIG_USB_NET_PLUSB) += plusb.o
obj-$(CONFIG_USB_NET_RNDIS_HOST) += rndis_host.o obj-$(CONFIG_USB_NET_RNDIS_HOST) += rndis_host.o
obj-$(CONFIG_USB_NET_CDC_SUBSET) += cdc_subset.o obj-$(CONFIG_USB_NET_CDC_SUBSET) += cdc_subset.o
obj-$(CONFIG_USB_NET_ZAURUS) += zaurus.o obj-$(CONFIG_USB_NET_ZAURUS) += zaurus.o
......
/*
* PL-2301/2302 USB host-to-host link cables
* Copyright (C) 2000-2005 by David Brownell
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
// #define DEBUG // error path messages, extra info
// #define VERBOSE // more; success messages
#include <linux/config.h>
#ifdef CONFIG_USB_DEBUG
# define DEBUG
#endif
#include <linux/module.h>
#include <linux/sched.h>
#include <linux/init.h>
#include <linux/netdevice.h>
#include <linux/etherdevice.h>
#include <linux/ethtool.h>
#include <linux/workqueue.h>
#include <linux/mii.h>
#include <linux/usb.h>
#include "usbnet.h"
/*
* Prolific PL-2301/PL-2302 driver ... http://www.prolifictech.com
*
* The protocol and handshaking used here should be bug-compatible
* with the Linux 2.2 "plusb" driver, by Deti Fliegl.
*
* HEADS UP: this handshaking isn't all that robust. This driver
* gets confused easily if you unplug one end of the cable then
* try to connect it again; you'll need to restart both ends. The
* "naplink" software (used by some PlayStation/2 deveopers) does
* the handshaking much better! Also, sometimes this hardware
* seems to get wedged under load. Prolific docs are weak, and
* don't identify differences between PL2301 and PL2302, much less
* anything to explain the different PL2302 versions observed.
*/
/*
* Bits 0-4 can be used for software handshaking; they're set from
* one end, cleared from the other, "read" with the interrupt byte.
*/
#define PL_S_EN (1<<7) /* (feature only) suspend enable */
/* reserved bit -- rx ready (6) ? */
#define PL_TX_READY (1<<5) /* (interrupt only) transmit ready */
#define PL_RESET_OUT (1<<4) /* reset output pipe */
#define PL_RESET_IN (1<<3) /* reset input pipe */
#define PL_TX_C (1<<2) /* transmission complete */
#define PL_TX_REQ (1<<1) /* transmission received */
#define PL_PEER_E (1<<0) /* peer exists */
static inline int
pl_vendor_req(struct usbnet *dev, u8 req, u8 val, u8 index)
{
return usb_control_msg(dev->udev,
usb_rcvctrlpipe(dev->udev, 0),
req,
USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
val, index,
NULL, 0,
USB_CTRL_GET_TIMEOUT);
}
static inline int
pl_clear_QuickLink_features(struct usbnet *dev, int val)
{
return pl_vendor_req(dev, 1, (u8) val, 0);
}
static inline int
pl_set_QuickLink_features(struct usbnet *dev, int val)
{
return pl_vendor_req(dev, 3, (u8) val, 0);
}
static int pl_reset(struct usbnet *dev)
{
/* some units seem to need this reset, others reject it utterly.
* FIXME be more like "naplink" or windows drivers.
*/
(void) pl_set_QuickLink_features(dev,
PL_S_EN|PL_RESET_OUT|PL_RESET_IN|PL_PEER_E);
return 0;
}
static const struct driver_info prolific_info = {
.description = "Prolific PL-2301/PL-2302",
.flags = FLAG_NO_SETINT,
/* some PL-2302 versions seem to fail usb_set_interface() */
.reset = pl_reset,
};
/*-------------------------------------------------------------------------*/
/*
* Proilific's name won't normally be on the cables, and
* may not be on the device.
*/
static const struct usb_device_id products [] = {
{
USB_DEVICE(0x067b, 0x0000), // PL-2301
.driver_info = (unsigned long) &prolific_info,
}, {
USB_DEVICE(0x067b, 0x0001), // PL-2302
.driver_info = (unsigned long) &prolific_info,
},
{ }, // END
};
MODULE_DEVICE_TABLE(usb, products);
static struct usb_driver plusb_driver = {
.owner = THIS_MODULE,
.name = "plusb",
.id_table = products,
.probe = usbnet_probe,
.disconnect = usbnet_disconnect,
.suspend = usbnet_suspend,
.resume = usbnet_resume,
};
static int __init plusb_init(void)
{
return usb_register(&plusb_driver);
}
module_init(plusb_init);
static void __exit plusb_exit(void)
{
usb_deregister(&plusb_driver);
}
module_exit(plusb_exit);
MODULE_AUTHOR("David Brownell");
MODULE_DESCRIPTION("Prolific PL-2301/2302 USB Host to Host Link Driver");
MODULE_LICENSE("GPL");
/* /*
* USB Networking Links * USB Network driver infrastructure
* Copyright (C) 2000-2005 by David Brownell * Copyright (C) 2000-2005 by David Brownell
* Copyright (C) 2003-2005 David Hollis <dhollis@davehollis.com> * Copyright (C) 2003-2005 David Hollis <dhollis@davehollis.com>
* *
...@@ -20,96 +20,15 @@ ...@@ -20,96 +20,15 @@
/* /*
* This is a generic "USB networking" framework that works with several * This is a generic "USB networking" framework that works with several
* kinds of full and high speed networking devices: * kinds of full and high speed networking devices: host-to-host cables,
* smart usb peripherals, and actual Ethernet adapters.
* *
* + USB host-to-host "network cables", used for IP-over-USB links. * These devices usually differ in terms of control protocols (if they
* These are often used for Laplink style connectivity products. * even have one!) and sometimes they define new framing to wrap or batch
* - AnchorChip 2720 * Ethernet packets. Otherwise, they talk to USB pretty much the same,
* - Belkin, eTEK (interops with Win32 drivers) * so interface (un)binding, endpoint I/O queues, fault handling, and other
* - GeneSys GL620USB-A * issues can usefully be addressed by this framework.
* - NetChip 1080 (interoperates with NetChip Win32 drivers) */
* - Prolific PL-2301/2302 (replaces "plusb" driver)
* - KC Technology KC2190
*
* + Smart USB devices can support such links directly, using Internet
* standard protocols instead of proprietary host-to-device links.
* - Linux PDAs like iPaq, Yopy, and Zaurus
* - The BLOB boot loader (for diskless booting)
* - Linux "gadgets", perhaps using PXA-2xx or Net2280 controllers
* - Devices using EPSON's sample USB firmware
* - CDC-Ethernet class devices, such as many cable modems
*
* + Adapters to networks such as Ethernet.
* - AX8817X based USB 2.0 products
*
* Links to these devices can be bridged using Linux Ethernet bridging.
* With minor exceptions, these all use similar USB framing for network
* traffic, but need different protocols for control traffic.
*
* USB devices can implement their side of this protocol at the cost
* of two bulk endpoints; it's not restricted to "cable" applications.
* See the SA1110, Zaurus, or EPSON device/client support in this driver;
* slave/target drivers such as "usb-eth" (on most SA-1100 PDAs) or
* "g_ether" (in the Linux "gadget" framework) implement that behavior
* within devices.
*
*
* CHANGELOG:
*
* 13-sep-2000 experimental, new
* 10-oct-2000 usb_device_id table created.
* 28-oct-2000 misc fixes; mostly, discard more TTL-mangled rx packets.
* 01-nov-2000 usb_device_id table and probing api update by
* Adam J. Richter <adam@yggdrasil.com>.
* 18-dec-2000 (db) tx watchdog, "net1080" renaming to "usbnet", device_info
* and prolific support, isolate net1080-specific bits, cleanup.
* fix unlink_urbs oops in D3 PM resume code path.
*
* 02-feb-2001 (db) fix tx skb sharing, packet length, match_flags, ...
* 08-feb-2001 stubbed in "linuxdev", maybe the SA-1100 folk can use it;
* AnchorChips 2720 support (from spec) for testing;
* fix bit-ordering problem with ethernet multicast addr
* 19-feb-2001 Support for clearing halt conditions. SA1100 UDC support
* updates. Oleg Drokin (green@iXcelerator.com)
* 25-mar-2001 More SA-1100 updates, including workaround for ip problem
* expecting cleared skb->cb and framing change to match latest
* handhelds.org version (Oleg). Enable device IDs from the
* Win32 Belkin driver; other cleanups (db).
* 16-jul-2001 Bugfixes for uhci oops-on-unplug, Belkin support, various
* cleanups for problems not yet seen in the field. (db)
* 17-oct-2001 Handle "Advance USBNET" product, like Belkin/eTEK devices,
* from Ioannis Mavroukakis <i.mavroukakis@btinternet.com>;
* rx unlinks somehow weren't async; minor cleanup.
* 03-nov-2001 Merged GeneSys driver; original code from Jiun-Jie Huang
* <huangjj@genesyslogic.com.tw>, updated by Stanislav Brabec
* <utx@penguin.cz>. Made framing options (NetChip/GeneSys)
* tie mostly to (sub)driver info. Workaround some PL-2302
* chips that seem to reject SET_INTERFACE requests.
*
* 06-apr-2002 Added ethtool support, based on a patch from Brad Hards.
* Level of diagnostics is more configurable; they use device
* location (usb_device->devpath) instead of address (2.5).
* For tx_fixup, memflags can't be NOIO.
* 07-may-2002 Generalize/cleanup keventd support, handling rx stalls (mostly
* for USB 2.0 TTs) and memory shortages (potential) too. (db)
* Use "locally assigned" IEEE802 address space. (Brad Hards)
* 18-oct-2002 Support for Zaurus (Pavel Machek), related cleanup (db).
* 14-dec-2002 Remove Zaurus-private crc32 code (Pavel); 2.5 oops fix,
* cleanups and stubbed PXA-250 support (db), fix for framing
* issues on Z, net1080, and gl620a (Toby Milne)
*
* 31-mar-2003 Use endpoint descriptors: high speed support, simpler sa1100
* vs pxa25x, and CDC Ethernet. Throttle down log floods on
* disconnect; other cleanups. (db) Flush net1080 fifos
* after several sequential framing errors. (Johannes Erdfelt)
* 22-aug-2003 AX8817X support (Dave Hollis).
*
* 14-jun-2004 Trivial patch for AX8817X based Buffalo LUA-U2-KTX in Japan
* (Neil Bortnak)
* 03-nov-2004 Trivial patch for KC2190 (KC-190) chip. (Jonathan McDowell)
*
* 01-feb-2005 AX88772 support (Phil Chang & Dave Hollis)
*-------------------------------------------------------------------------*/
// #define DEBUG // error path messages, extra info // #define DEBUG // error path messages, extra info
// #define VERBOSE // more; success messages // #define VERBOSE // more; success messages
...@@ -301,77 +220,6 @@ void usbnet_skb_return (struct usbnet *dev, struct sk_buff *skb) ...@@ -301,77 +220,6 @@ void usbnet_skb_return (struct usbnet *dev, struct sk_buff *skb)
} }
EXPORT_SYMBOL_GPL(usbnet_skb_return); EXPORT_SYMBOL_GPL(usbnet_skb_return);
#ifdef CONFIG_USB_PL2301
#define HAVE_HARDWARE
/*-------------------------------------------------------------------------
*
* Prolific PL-2301/PL-2302 driver ... http://www.prolifictech.com
*
* The protocol and handshaking used here should be bug-compatible
* with the Linux 2.2 "plusb" driver, by Deti Fliegl.
*
*-------------------------------------------------------------------------*/
/*
* Bits 0-4 can be used for software handshaking; they're set from
* one end, cleared from the other, "read" with the interrupt byte.
*/
#define PL_S_EN (1<<7) /* (feature only) suspend enable */
/* reserved bit -- rx ready (6) ? */
#define PL_TX_READY (1<<5) /* (interrupt only) transmit ready */
#define PL_RESET_OUT (1<<4) /* reset output pipe */
#define PL_RESET_IN (1<<3) /* reset input pipe */
#define PL_TX_C (1<<2) /* transmission complete */
#define PL_TX_REQ (1<<1) /* transmission received */
#define PL_PEER_E (1<<0) /* peer exists */
static inline int
pl_vendor_req (struct usbnet *dev, u8 req, u8 val, u8 index)
{
return usb_control_msg (dev->udev,
usb_rcvctrlpipe (dev->udev, 0),
req,
USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
val, index,
NULL, 0,
USB_CTRL_GET_TIMEOUT);
}
static inline int
pl_clear_QuickLink_features (struct usbnet *dev, int val)
{
return pl_vendor_req (dev, 1, (u8) val, 0);
}
static inline int
pl_set_QuickLink_features (struct usbnet *dev, int val)
{
return pl_vendor_req (dev, 3, (u8) val, 0);
}
/*-------------------------------------------------------------------------*/
static int pl_reset (struct usbnet *dev)
{
/* some units seem to need this reset, others reject it utterly.
* FIXME be more like "naplink" or windows drivers.
*/
(void) pl_set_QuickLink_features (dev,
PL_S_EN|PL_RESET_OUT|PL_RESET_IN|PL_PEER_E);
return 0;
}
static const struct driver_info prolific_info = {
.description = "Prolific PL-2301/PL-2302",
.flags = FLAG_NO_SETINT,
/* some PL-2302 versions seem to fail usb_set_interface() */
.reset = pl_reset,
};
#endif /* CONFIG_USB_PL2301 */
/*------------------------------------------------------------------------- /*-------------------------------------------------------------------------
* *
...@@ -1354,62 +1202,24 @@ int usbnet_resume (struct usb_interface *intf) ...@@ -1354,62 +1202,24 @@ int usbnet_resume (struct usb_interface *intf)
EXPORT_SYMBOL_GPL(usbnet_resume); EXPORT_SYMBOL_GPL(usbnet_resume);
/*-------------------------------------------------------------------------*/
#ifndef HAVE_HARDWARE
#error You need to configure some hardware for this driver
#endif
/*
* chip vendor names won't normally be on the cables, and
* may not be on the device.
*/
static const struct usb_device_id products [] = {
#ifdef CONFIG_USB_PL2301
{
USB_DEVICE (0x067b, 0x0000), // PL-2301
.driver_info = (unsigned long) &prolific_info,
}, {
USB_DEVICE (0x067b, 0x0001), // PL-2302
.driver_info = (unsigned long) &prolific_info,
},
#endif
{ }, // END
};
MODULE_DEVICE_TABLE (usb, products);
static struct usb_driver usbnet_driver = {
.owner = THIS_MODULE,
.name = driver_name,
.id_table = products,
.probe = usbnet_probe,
.disconnect = usbnet_disconnect,
.suspend = usbnet_suspend,
.resume = usbnet_resume,
};
/*-------------------------------------------------------------------------*/ /*-------------------------------------------------------------------------*/
static int __init usbnet_init(void) static int __init usbnet_init(void)
{ {
// compiler should optimize these out /* compiler should optimize this out */
BUG_ON (sizeof (((struct sk_buff *)0)->cb) BUG_ON (sizeof (((struct sk_buff *)0)->cb)
< sizeof (struct skb_data)); < sizeof (struct skb_data));
random_ether_addr(node_id); random_ether_addr(node_id);
return 0;
return usb_register(&usbnet_driver);
} }
module_init(usbnet_init); module_init(usbnet_init);
static void __exit usbnet_exit(void) static void __exit usbnet_exit(void)
{ {
usb_deregister(&usbnet_driver);
} }
module_exit(usbnet_exit); module_exit(usbnet_exit);
MODULE_AUTHOR("David Brownell"); MODULE_AUTHOR("David Brownell");
MODULE_DESCRIPTION("USB Host-to-Host Link Drivers (numerous vendors)"); MODULE_DESCRIPTION("USB network driver framework");
MODULE_LICENSE("GPL"); MODULE_LICENSE("GPL");
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment