PCI: Remove users of pci_enable_device_bars()

This patch converts users of pci_enable_device_bars() to the new
pci_enable_device_{io,mem} interface.

The new API fits nicely, except maybe for the QLA case where a bit of
code re-organization might be a good idea but I prefer sticking to the
simple patch as I don't have hardware to test on.

I'll also need some feedback on the cs5520 change.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

drivers/ata/pata_cs5520.c

@@ -229,7 +229,7 @@ static int __devinit cs5520_init_one(struct pci_dev *pdev, const struct pci_devi
 		return -ENOMEM;
 
 	/* Perform set up for DMA */
-	if (pci_enable_device_bars(pdev, 1<<2)) {
+	if (pci_enable_device_io(pdev)) {
 		printk(KERN_ERR DRV_NAME ": unable to configure BAR2.\n");
 		return -ENODEV;
 	}

drivers/i2c/busses/scx200_acb.c

@@ -492,7 +492,7 @@ static __init int scx200_create_pci(const char *text, struct pci_dev *pdev,
 	iface->pdev = pdev;
 	iface->bar = bar;
 
-	rc = pci_enable_device_bars(iface->pdev, 1 << iface->bar);
+	rc = pci_enable_device_io(iface->pdev);
 	if (rc)
 		goto errout_free;
 

drivers/ide/pci/cs5520.c

@@ -156,8 +156,14 @@ static int __devinit cs5520_init_one(struct pci_dev *dev, const struct pci_devic
 	ide_setup_pci_noise(dev, d);
 
 	/* We must not grab the entire device, it has 'ISA' space in its
-	   BARS too and we will freak out other bits of the kernel */
-	if (pci_enable_device_bars(dev, 1<<2)) {
+	 * BARS too and we will freak out other bits of the kernel
+	 *
+	 * pci_enable_device_bars() is going away. I replaced it with
+	 * IO only enable for now but I'll need confirmation this is
+	 * allright for that device. If not, it will need some kind of
+	 * quirk. --BenH.
+	 */
+	if (pci_enable_device_io(dev)) {
 		printk(KERN_WARNING "%s: Unable to enable 55x0.\n", d->name);
 		return -ENODEV;
 	}

drivers/ide/setup-pci.c

@@ -240,7 +240,9 @@ EXPORT_SYMBOL_GPL(ide_setup_pci_noise);
  *	@d: IDE port info
  *
  *	Enable the IDE PCI device. We attempt to enable the device in full
- *	but if that fails then we only need BAR4 so we will enable that.
+ *	but if that fails then we only need IO space. The PCI code should
+ *	have setup the proper resources for us already for controllers in
+ *	legacy mode.
  *	
  *	Returns zero on success or an error code
  */
@@ -250,7 +252,7 @@ static int ide_pci_enable(struct pci_dev *dev, const struct ide_port_info *d)
 	int ret;
 
 	if (pci_enable_device(dev)) {
-		ret = pci_enable_device_bars(dev, 1 << 4);
+		ret = pci_enable_device_io(dev);
 		if (ret < 0) {
 			printk(KERN_WARNING "%s: (ide_setup_pci_device:) "
 				"Could not enable device.\n", d->name);

drivers/scsi/lpfc/lpfc_init.c

@@ -2296,10 +2296,9 @@ static pci_ers_result_t lpfc_io_slot_reset(struct pci_dev *pdev)
 	struct Scsi_Host *shost = pci_get_drvdata(pdev);
 	struct lpfc_hba *phba = ((struct lpfc_vport *)shost->hostdata)->phba;
 	struct lpfc_sli *psli = &phba->sli;
-	int bars = pci_select_bars(pdev, IORESOURCE_MEM);
 
 	dev_printk(KERN_INFO, &pdev->dev, "recovering from a slot reset.\n");
-	if (pci_enable_device_bars(pdev, bars)) {
+	if (pci_enable_device_mem(pdev)) {
 		printk(KERN_ERR "lpfc: Cannot re-enable "
 			"PCI device after reset.\n");
 		return PCI_ERS_RESULT_DISCONNECT;

drivers/scsi/qla2xxx/qla_def.h

@@ -2268,6 +2268,7 @@ typedef struct scsi_qla_host {
 	spinlock_t		hardware_lock ____cacheline_aligned;
 
 	int		bars;
+	int		mem_only;
 	device_reg_t __iomem *iobase;		/* Base I/O address */
 	resource_size_t pio_address;
 #define MIN_IOBASE_LEN		0x100

drivers/scsi/qla2xxx/qla_os.c

@@ -1564,7 +1564,7 @@ qla2x00_probe_one(struct pci_dev *pdev, const struct pci_device_id *id)
 	char pci_info[30];
 	char fw_str[30];
 	struct scsi_host_template *sht;
-	int bars;
+	int bars, mem_only = 0;
 
 	bars = pci_select_bars(pdev, IORESOURCE_MEM | IORESOURCE_IO);
 	sht = &qla2x00_driver_template;
@@ -1575,10 +1575,16 @@ qla2x00_probe_one(struct pci_dev *pdev, const struct pci_device_id *id)
 	    pdev->device == PCI_DEVICE_ID_QLOGIC_ISP2532) {
 		bars = pci_select_bars(pdev, IORESOURCE_MEM);
 		sht = &qla24xx_driver_template;
+		mem_only = 1;
 	}
 
-	if (pci_enable_device_bars(pdev, bars))
-		goto probe_out;
+	if (mem_only) {
+		if (pci_enable_device_mem(pdev))
+			goto probe_out;
+	} else {
+		if (pci_enable_device(pdev))
+			goto probe_out;
+	}
 
 	if (pci_find_aer_capability(pdev))
 		if (pci_enable_pcie_error_reporting(pdev))
@@ -1601,6 +1607,7 @@ qla2x00_probe_one(struct pci_dev *pdev, const struct pci_device_id *id)
 	sprintf(ha->host_str, "%s_%ld", QLA2XXX_DRIVER_NAME, ha->host_no);
 	ha->parent = NULL;
 	ha->bars = bars;
+	ha->mem_only = mem_only;
 
 	/* Set ISP-type information. */
 	qla2x00_set_isp_flags(ha);
@@ -2875,8 +2882,14 @@ qla2xxx_pci_slot_reset(struct pci_dev *pdev)
 {
 	pci_ers_result_t ret = PCI_ERS_RESULT_DISCONNECT;
 	scsi_qla_host_t *ha = pci_get_drvdata(pdev);
+	int rc;
+
+	if (ha->mem_only)
+		rc = pci_enable_device_mem(pdev);
+	else
+		rc = pci_enable_device(pdev);
 
-	if (pci_enable_device_bars(pdev, ha->bars)) {
+	if (rc) {
 		qla_printk(KERN_WARNING, ha,
 		    "Can't re-enable PCI device after reset.\n");