ixgbe: Enable flow control pause parameter auto-negotiation support

This patch enables flow control pause parameters auto-negotiation support
to 82599 based 10G Base-T, backplane devices and multi-speed fiber optics
modules at 1G speed
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

drivers/net/ixgbe/ixgbe_82598.c

@@ -366,7 +366,7 @@ static s32 ixgbe_fc_enable_82598(struct ixgbe_hw *hw, s32 packetbuf_num)
 
 	/* Negotiate the fc mode to use */
 	ret_val = ixgbe_fc_autoneg(hw);
-	if (ret_val)
+	if (ret_val == IXGBE_ERR_FLOW_CONTROL)
 		goto out;
 
 	/* Disable any previous flow control settings */
@@ -384,10 +384,10 @@ static s32 ixgbe_fc_enable_82598(struct ixgbe_hw *hw, s32 packetbuf_num)
 	 * 2: Tx flow control is enabled (we can send pause frames but
 	 *     we do not support receiving pause frames).
 	 * 3: Both Rx and Tx flow control (symmetric) are enabled.
-	 * other: Invalid.
 #ifdef CONFIG_DCB
 	 * 4: Priority Flow Control is enabled.
 #endif
+	 * other: Invalid.
 	 */
 	switch (hw->fc.current_mode) {
 	case ixgbe_fc_none:
@@ -444,9 +444,10 @@ static s32 ixgbe_fc_enable_82598(struct ixgbe_hw *hw, s32 packetbuf_num)
 		reg = (rx_pba_size - hw->fc.low_water) << 6;
 		if (hw->fc.send_xon)
 			reg |= IXGBE_FCRTL_XONE;
+
 		IXGBE_WRITE_REG(hw, IXGBE_FCRTL(packetbuf_num), reg);
 
-		reg = (rx_pba_size - hw->fc.high_water) << 10;
+		reg = (rx_pba_size - hw->fc.high_water) << 6;
 		reg |= IXGBE_FCRTH_FCEN;
 
 		IXGBE_WRITE_REG(hw, IXGBE_FCRTH(packetbuf_num), reg);

drivers/net/ixgbe/ixgbe_82599.c

@@ -772,6 +772,9 @@ static s32 ixgbe_setup_mac_link_82599(struct ixgbe_hw *hw,
 
 	/* Check to see if speed passed in is supported. */
 	hw->mac.ops.get_link_capabilities(hw, &link_capabilities, &autoneg);
+	if (status != 0)
+		goto out;
+
 	speed &= link_capabilities;
 
 	if (speed == IXGBE_LINK_SPEED_UNKNOWN) {

drivers/net/ixgbe/ixgbe_main.c

@@ -3775,7 +3775,8 @@ static int ixgbe_non_sfp_link_config(struct ixgbe_hw *hw)
 	if (ret)
 		goto link_cfg_out;
 
-	if (hw->mac.ops.get_link_capabilities)
+	autoneg = hw->phy.autoneg_advertised;
+	if ((!autoneg) && (hw->mac.ops.get_link_capabilities))
 		ret = hw->mac.ops.get_link_capabilities(hw, &autoneg,
 							&negotiation);
 	if (ret)

drivers/net/ixgbe/ixgbe_phy.h

@@ -58,6 +58,10 @@
 #define IXGBE_I2C_EEPROM_STATUS_FAIL         0x2
 #define IXGBE_I2C_EEPROM_STATUS_IN_PROGRESS  0x3
 
+/* Flow control defines */
+#define IXGBE_TAF_SYM_PAUSE                  0x400
+#define IXGBE_TAF_ASM_PAUSE                  0x800
+
 /* Bit-shift macros */
 #define IXGBE_SFF_VENDOR_OUI_BYTE0_SHIFT    24
 #define IXGBE_SFF_VENDOR_OUI_BYTE1_SHIFT    16

drivers/net/ixgbe/ixgbe_type.h

@@ -2698,6 +2698,9 @@ struct ixgbe_info {
 #define IXGBE_ERR_EEPROM_VERSION                -24
 #define IXGBE_ERR_NO_SPACE                      -25
 #define IXGBE_ERR_OVERTEMP                      -26
+#define IXGBE_ERR_FC_NOT_NEGOTIATED             -27
+#define IXGBE_ERR_FC_NOT_SUPPORTED              -28
+#define IXGBE_ERR_FLOW_CONTROL                  -29
 #define IXGBE_ERR_SFP_SETUP_NOT_COMPLETE        -30
 #define IXGBE_ERR_PBA_SECTION                   -31
 #define IXGBE_ERR_INVALID_ARGUMENT              -32