Merge tag 'sunxi-dt-for-4.15-2' of...

Merge tag 'sunxi-dt-for-4.15-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt

Pull "Allwinner DT changes for 4.15, take 2" from Maxime Ripard:

Here are a few commits that would be great to get in 4.15, given how
long they've been hanging around.

The first and most important one is the reintroduction of the EMAC DT
changes after they've been reverted at the last minute in 4.13.

There's a arm64 patch that crept in because the H5 and H3 share a
common DTSI that is located in arch/arm, and merging that patch
through the arm64 PR, especially given the pull requests that have
already been sent, would just have generated too many conflicts.

* tag 'sunxi-dt-for-4.15-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
  ARM: dts: sun8i: a711: Enable USB OTG
  ARM: dts: sun8i: a711: Add regulator support
  ARM: dts: sun8i: a83t: bananapi-m3: Enable AP6212 WiFi on mmc1
  ARM: dts: sun8i: a83t: cubietruck-plus: Enable AP6330 WiFi on mmc1
  ARM: dts: sun8i: a83t: Move mmc1 pinctrl setting to dtsi file
  ARM: dts: sun8i: a83t: allwinner-h8homlet-v2: Add AXP818 regulator nodes
  ARM: dts: sun8i: a83t: bananapi-m3: Add AXP813 regulator nodes
  ARM: dts: sun8i: a83t: cubietruck-plus: Add AXP818 regulator nodes
  ARM: dts: sunxi: Add dtsi for AXP81x PMIC
  arm64: dts: allwinner: H5: Restore EMAC changes
  ARM: dts: sunxi: Restore EMAC changes (boards)
  ARM: dts: sunxi: h3/h5: represent the mdio switch used by sun8i-h3-emac
  arm: dts: sunxi: h3/h5: Restore EMAC changes
  dt-bindings: net: dwmac-sun8i: update documentation about integrated PHY
  dt-bindings: net: Restore sun8i dwmac binding

Documentation/devicetree/bindings/net/dwmac-sun8i.txt

+* Allwinner sun8i GMAC ethernet controller
+
+This device is a platform glue layer for stmmac.
+Please see stmmac.txt for the other unchanged properties.
+
+Required properties:
+- compatible: must be one of the following string:
+		"allwinner,sun8i-a83t-emac"
+		"allwinner,sun8i-h3-emac"
+		"allwinner,sun8i-v3s-emac"
+		"allwinner,sun50i-a64-emac"
+- reg: address and length of the register for the device.
+- interrupts: interrupt for the device
+- interrupt-names: must be "macirq"
+- clocks: A phandle to the reference clock for this device
+- clock-names: must be "stmmaceth"
+- resets: A phandle to the reset control for this device
+- reset-names: must be "stmmaceth"
+- phy-mode: See ethernet.txt
+- phy-handle: See ethernet.txt
+- #address-cells: shall be 1
+- #size-cells: shall be 0
+- syscon: A phandle to the syscon of the SoC with one of the following
+ compatible string:
+  - allwinner,sun8i-h3-system-controller
+  - allwinner,sun8i-v3s-system-controller
+  - allwinner,sun50i-a64-system-controller
+  - allwinner,sun8i-a83t-system-controller
+
+Optional properties:
+- allwinner,tx-delay-ps: TX clock delay chain value in ps. Range value is 0-700. Default is 0)
+- allwinner,rx-delay-ps: RX clock delay chain value in ps. Range value is 0-3100. Default is 0)
+Both delay properties need to be a multiple of 100. They control the delay for
+external PHY.
+
+Optional properties for the following compatibles:
+  - "allwinner,sun8i-h3-emac",
+  - "allwinner,sun8i-v3s-emac":
+- allwinner,leds-active-low: EPHY LEDs are active low
+
+Required child node of emac:
+- mdio bus node: should be named mdio with compatible "snps,dwmac-mdio"
+
+Required properties of the mdio node:
+- #address-cells: shall be 1
+- #size-cells: shall be 0
+
+The device node referenced by "phy" or "phy-handle" must be a child node
+of the mdio node. See phy.txt for the generic PHY bindings.
+
+The following compatibles require that the emac node have a mdio-mux child
+node called "mdio-mux":
+  - "allwinner,sun8i-h3-emac"
+  - "allwinner,sun8i-v3s-emac":
+Required properties for the mdio-mux node:
+  - compatible = "allwinner,sun8i-h3-mdio-mux"
+  - mdio-parent-bus: a phandle to EMAC mdio
+  - one child mdio for the integrated mdio with the compatible
+    "allwinner,sun8i-h3-mdio-internal"
+  - one child mdio for the external mdio if present (V3s have none)
+Required properties for the mdio-mux children node:
+  - reg: 1 for internal MDIO bus, 2 for external MDIO bus
+
+The following compatibles require a PHY node representing the integrated
+PHY, under the integrated MDIO bus node if an mdio-mux node is used:
+  - "allwinner,sun8i-h3-emac",
+  - "allwinner,sun8i-v3s-emac":
+
+Additional information regarding generic multiplexer properties can be found
+at Documentation/devicetree/bindings/net/mdio-mux.txt
+
+Required properties of the integrated phy node:
+- clocks: a phandle to the reference clock for the EPHY
+- resets: a phandle to the reset control for the EPHY
+- Must be a child of the integrated mdio
+
+Example with integrated PHY:
+emac: ethernet@1c0b000 {
+	compatible = "allwinner,sun8i-h3-emac";
+	syscon = <&syscon>;
+	reg = <0x01c0b000 0x104>;
+	interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+	interrupt-names = "macirq";
+	resets = <&ccu RST_BUS_EMAC>;
+	reset-names = "stmmaceth";
+	clocks = <&ccu CLK_BUS_EMAC>;
+	clock-names = "stmmaceth";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	phy-handle = <&int_mii_phy>;
+	phy-mode = "mii";
+	allwinner,leds-active-low;
+
+	mdio: mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+	};
+
+	mdio-mux {
+		compatible = "mdio-mux", "allwinner,sun8i-h3-mdio-mux";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mdio-parent-bus = <&mdio>;
+
+		int_mdio: mdio@1 {
+			compatible = "allwinner,sun8i-h3-mdio-internal";
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			int_mii_phy: ethernet-phy@1 {
+				reg = <1>;
+				clocks = <&ccu CLK_BUS_EPHY>;
+				resets = <&ccu RST_BUS_EPHY>;
+				phy-is-integrated;
+			};
+		};
+		ext_mdio: mdio@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+Example with external PHY:
+emac: ethernet@1c0b000 {
+	compatible = "allwinner,sun8i-h3-emac";
+	syscon = <&syscon>;
+	reg = <0x01c0b000 0x104>;
+	interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+	interrupt-names = "macirq";
+	resets = <&ccu RST_BUS_EMAC>;
+	reset-names = "stmmaceth";
+	clocks = <&ccu CLK_BUS_EMAC>;
+	clock-names = "stmmaceth";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	phy-handle = <&ext_rgmii_phy>;
+	phy-mode = "rgmii";
+	allwinner,leds-active-low;
+
+	mdio: mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+	};
+
+	mdio-mux {
+		compatible = "allwinner,sun8i-h3-mdio-mux";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mdio-parent-bus = <&mdio>;
+
+		int_mdio: mdio@1 {
+			compatible = "allwinner,sun8i-h3-mdio-internal";
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			int_mii_phy: ethernet-phy@1 {
+				reg = <1>;
+				clocks = <&ccu CLK_BUS_EPHY>;
+				resets = <&ccu RST_BUS_EPHY>;
+			};
+		};
+		ext_mdio: mdio@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			ext_rgmii_phy: ethernet-phy@1 {
+				reg = <1>;
+			};
+		}:
+	};
+};
+
+Example with SoC without integrated PHY
+
+emac: ethernet@1c0b000 {
+	compatible = "allwinner,sun8i-a83t-emac";
+	syscon = <&syscon>;
+	reg = <0x01c0b000 0x104>;
+	interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+	interrupt-names = "macirq";
+	resets = <&ccu RST_BUS_EMAC>;
+	reset-names = "stmmaceth";
+	clocks = <&ccu CLK_BUS_EMAC>;
+	clock-names = "stmmaceth";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	phy-handle = <&ext_rgmii_phy>;
+	phy-mode = "rgmii";
+
+	mdio: mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		ext_rgmii_phy: ethernet-phy@1 {
+			reg = <1>;
+		};
+	};
+};

arch/arm/boot/dts/axp81x.dtsi

+/*
+ * Copyright 2017 Chen-Yu Tsai
+ *
+ * Chen-Yu Tsai <wens@csie.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/* AXP813/818 Integrated Power Management Chip */
+
+&axp81x {
+	interrupt-controller;
+	#interrupt-cells = <1>;
+
+	regulators {
+		/* Default work frequency for buck regulators */
+		x-powers,dcdc-freq = <3000>;
+
+		reg_dcdc1: dcdc1 {
+		};
+
+		reg_dcdc2: dcdc2 {
+		};
+
+		reg_dcdc3: dcdc3 {
+		};
+
+		reg_dcdc4: dcdc4 {
+		};
+
+		reg_dcdc5: dcdc5 {
+		};
+
+		reg_dcdc6: dcdc6 {
+		};
+
+		reg_dcdc7: dcdc7 {
+		};
+
+		reg_aldo1: aldo1 {
+		};
+
+		reg_aldo2: aldo2 {
+		};
+
+		reg_aldo3: aldo3 {
+		};
+
+		reg_dldo1: dldo1 {
+		};
+
+		reg_dldo2: dldo2 {
+		};
+
+		reg_dldo3: dldo3 {
+		};
+
+		reg_dldo4: dldo4 {
+		};
+
+		reg_eldo1: eldo1 {
+		};
+
+		reg_eldo2: eldo2 {
+		};
+
+		reg_eldo3: eldo3 {
+		};
+
+		reg_fldo1: fldo1 {
+		};
+
+		reg_fldo2: fldo2 {
+		};
+
+		reg_fldo3: fldo3 {
+		};
+
+		reg_ldo_io0: ldo-io0 {
+			/* Disable by default to avoid conflicts with GPIO */
+			status = "disabled";
+		};
+
+		reg_ldo_io1: ldo-io1 {
+			/* Disable by default to avoid conflicts with GPIO */
+			status = "disabled";
+		};
+
+		reg_rtc_ldo: rtc-ldo {
+			/* RTC_LDO is a fixed, always-on regulator */
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		reg_sw: sw {
+		};
+
+		reg_drivevbus: drivevbus {
+			status = "disabled";
+		};
+	};
+};

arch/arm/boot/dts/sun8i-a83t-allwinner-h8homlet-v2.dts

@@ -43,7 +43,8 @@
 
 /dts-v1/;
 #include "sun8i-a83t.dtsi"
-#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	model = "Allwinner A83T H8Homlet Proto Dev Board v2.0";
@@ -56,6 +57,26 @@ aliases {
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
+
+	reg_usb0_vbus: reg-usb0-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb0-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&r_pio 0 5 GPIO_ACTIVE_HIGH>; /* PL5 */
+	};
+
+	reg_usb1_vbus: reg-usb1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb1-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
+	};
 };
 
 &ehci0 {
@@ -65,7 +86,7 @@ &ehci0 {
 &mmc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins>;
-	vmmc-supply = <&reg_vcc3v0>;
+	vmmc-supply = <&reg_dcdc1>;
 	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
 	bus-width = <4>;
 	cd-inverted;
@@ -75,7 +96,8 @@ &mmc0 {
 &mmc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc2_8bit_emmc_pins>;
-	vmmc-supply = <&reg_vcc3v0>;
+	vmmc-supply = <&reg_dcdc1>;
+	vqmmc-supply = <&reg_dcdc1>;
 	bus-width = <8>;
 	non-removable;
 	cap-mmc-hw-reset;
@@ -86,16 +108,6 @@ &ohci0 {
 	status = "okay";
 };
 
-&reg_usb0_vbus {
-	gpio = <&r_pio 0 5 GPIO_ACTIVE_HIGH>; /* PL5 */
-	status = "okay";
-};
-
-&reg_usb1_vbus {
-	gpio = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
-	status = "okay";
-};
-
 &r_rsb {
 	status = "okay";
 
@@ -104,6 +116,8 @@ axp81x: pmic@3a3 {
 		reg = <0x3a3>;
 		interrupt-parent = <&r_intc>;
 		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		eldoin-supply = <&reg_dcdc1>;
+		swin-supply = <&reg_dcdc1>;
 	};
 
 	ac100: codec@e89 {
@@ -131,6 +145,113 @@ ac100_rtc: rtc {
 	};
 };
 
+#include "axp81x.dtsi"
+
+&reg_aldo1 {
+	regulator-always-on;
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "vcc-1v8";
+};
+
+&reg_aldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "dram-pll";
+};
+
+&reg_aldo3 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "avcc";
+};
+
+&reg_dcdc1 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-3v3";
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <700000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-cpua";
+};
+
+&reg_dcdc3 {
+	regulator-always-on;
+	regulator-min-microvolt = <700000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-cpub";
+};
+
+&reg_dcdc4 {
+	regulator-min-microvolt = <700000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-gpu";
+};
+
+&reg_dcdc5 {
+	regulator-always-on;
+	regulator-min-microvolt = <1500000>;
+	regulator-max-microvolt = <1500000>;
+	regulator-name = "vcc-dram";
+};
+
+&reg_dcdc6 {
+	regulator-always-on;
+	regulator-min-microvolt = <900000>;
+	regulator-max-microvolt = <900000>;
+	regulator-name = "vdd-sys";
+};
+
+&reg_dldo2 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-mipi";
+};
+
+&reg_dldo4 {
+	/*
+	 * The PHY requires 20ms after all voltages are applied until core
+	 * logic is ready and 30ms after the reset pin is de-asserted.
+	 * Set a 100ms delay to account for PMIC ramp time and board traces.
+	 */
+	regulator-enable-ramp-delay = <100000>;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-ephy";
+};
+
+&reg_fldo1 {
+	regulator-min-microvolt = <1080000>;
+	regulator-max-microvolt = <1320000>;
+	regulator-name = "vdd12-hsic";
+};
+
+&reg_fldo2 {
+	/*
+	 * Despite the embedded CPUs core not being used in any way,
+	 * this must remain on or the system will hang.
+	 */
+	regulator-always-on;
+	regulator-min-microvolt = <700000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-cpus";
+};
+
+&reg_rtc_ldo {
+	regulator-name = "vcc-rtc";
+};
+
+&reg_sw {
+	regulator-name = "vcc-wifi";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pb_pins>;

arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts

@@ -44,7 +44,6 @@
 
 /dts-v1/;
 #include "sun8i-a83t.dtsi"
-#include "sunxi-common-regulators.dtsi"
 
 #include <dt-bindings/gpio/gpio.h>
 
@@ -59,6 +58,27 @@ aliases {
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
+
+	reg_usb1_vbus: reg-usb1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb1-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */
+	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&ac100_rtc 1>;
+		clock-names = "ext_clock";
+		/* The WiFi low power clock must be 32768 Hz */
+		assigned-clocks = <&ac100_rtc 1>;
+		assigned-clock-rates = <32768>;
+		/* enables internal regulator and de-asserts reset */
+		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 WL-PMU-EN */
+	};
 };
 
 &ehci0 {
@@ -71,17 +91,35 @@ &ehci0 {
 &mmc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins>;
-	vmmc-supply = <&reg_vcc3v3>;
+	vmmc-supply = <&reg_dcdc1>;
 	bus-width = <4>;
 	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
 	cd-inverted;
 	status = "okay";
 };
 
+&mmc1 {
+	vmmc-supply = <&reg_dldo1>;
+	vqmmc-supply = <&reg_dldo1>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+		interrupt-parent = <&r_pio>;
+		interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-names = "host-wake";
+	};
+};
+
 &mmc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc2_8bit_emmc_pins>;
-	vmmc-supply = <&reg_vcc3v3>;
+	vmmc-supply = <&reg_dcdc1>;
+	vqmmc-supply = <&reg_dcdc1>;
 	bus-width = <8>;
 	non-removable;
 	cap-mmc-hw-reset;
@@ -96,6 +134,10 @@ axp81x: pmic@3a3 {
 		reg = <0x3a3>;
 		interrupt-parent = <&r_intc>;
 		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		eldoin-supply = <&reg_dcdc1>;
+		fldoin-supply = <&reg_dcdc5>;
+		swin-supply = <&reg_dcdc1>;
+		x-powers,drive-vbus-en;
 	};
 
 	ac100: codec@e89 {
@@ -123,17 +165,126 @@ ac100_rtc: rtc {
 	};
 };
 
-&reg_usb1_vbus {
-	gpio = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */
+#include "axp81x.dtsi"
+
+&reg_aldo1 {
+	regulator-always-on;
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "vcc-1v8";
+};
+
+&reg_aldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "dram-pll";
+};
+
+&reg_aldo3 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "avcc";
+};
+
+&reg_dcdc1 {
+	/* schematics says 3.1V but FEX file says 3.3V */
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-3v3";
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <700000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-cpua";
+};
+
+&reg_dcdc3 {
+	regulator-always-on;
+	regulator-min-microvolt = <700000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-cpub";
+};
+
+&reg_dcdc4 {
+	regulator-min-microvolt = <700000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-gpu";
+};
+
+&reg_dcdc5 {
+	regulator-always-on;
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1200000>;
+	regulator-name = "vcc-dram";
+};
+
+&reg_dcdc6 {
+	regulator-always-on;
+	regulator-min-microvolt = <900000>;
+	regulator-max-microvolt = <900000>;
+	regulator-name = "vdd-sys";
+};
+
+&reg_dldo1 {
+	/*
+	 * This powers both the WiFi/BT module's main power, I/O supply,
+	 * and external pull-ups on all the data lines. It should be set
+	 * to the same voltage as the I/O supply (DCDC1 in this case) to
+	 * avoid any leakage or mismatch.
+	 */
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi";
+};
+
+&reg_dldo3 {
+	regulator-always-on;
+	regulator-min-microvolt = <2500000>;
+	regulator-max-microvolt = <2500000>;
+	regulator-name = "vcc-pd";
+};
+
+&reg_drivevbus {
+	regulator-name = "usb0-vbus";
 	status = "okay";
 };
 
-&reg_vcc3v0 {
-	status = "disabled";
+&reg_fldo1 {
+	regulator-min-microvolt = <1080000>;
+	regulator-max-microvolt = <1320000>;
+	regulator-name = "vdd12-hsic";
+};
+
+&reg_fldo2 {
+	/*
+	 * Despite the embedded CPUs core not being used in any way,
+	 * this must remain on or the system will hang.
+	 */
+	regulator-always-on;
+	regulator-min-microvolt = <700000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-cpus";
+};
+
+&reg_rtc_ldo {
+	regulator-name = "vcc-rtc";
 };
 
-&reg_vcc5v0 {
-	status = "disabled";
+&reg_sw {
+	/*
+	 * The PHY requires 20ms after all voltages
+	 * are applied until core logic is ready and
+	 * 30ms after the reset pin is de-asserted.
+	 * Set a 100ms delay to account for PMIC
+	 * ramp time and board traces.
+	 */
+	regulator-enable-ramp-delay = <100000>;
+	regulator-name = "vcc-ephy";
 };
 
 &uart0 {

arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts

@@ -44,7 +44,6 @@
 
 /dts-v1/;
 #include "sun8i-a83t.dtsi"
-#include "sunxi-common-regulators.dtsi"
 
 #include <dt-bindings/gpio/gpio.h>
 
@@ -95,6 +94,26 @@ usb-hub {
 		refclk-frequency = <19200000>;
 	};
 
+	reg_usb1_vbus: reg-usb1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb1-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&pio 3 29 GPIO_ACTIVE_HIGH>; /* PD29 */
+	};
+
+	reg_usb2_vbus: reg-usb2-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb2-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
+	};
+
 	sound {
 		compatible = "simple-audio-card";
 		simple-audio-card,name = "On-board SPDIF";
@@ -112,6 +131,17 @@ spdif_out: spdif-out {
 		#sound-dai-cells = <0>;
 		compatible = "linux,spdif-dit";
 	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&ac100_rtc 1>;
+		clock-names = "ext_clock";
+		/* The WiFi low power clock must be 32768 Hz */
+		assigned-clocks = <&ac100_rtc 1>;
+		assigned-clock-rates = <32768>;
+		/* enables internal regulator and de-asserts reset */
+		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 WL-PMU-EN */
+	};
 };
 
 &ehci0 {
@@ -127,17 +157,26 @@ &ehci1 {
 &mmc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins>;
-	vmmc-supply = <&reg_vcc3v3>;
+	vmmc-supply = <&reg_dcdc1>;
 	bus-width = <4>;
 	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
 	cd-inverted;
 	status = "okay";
 };
 
+&mmc1 {
+	vmmc-supply = <&reg_dcdc1>;
+	vqmmc-supply = <&reg_sw>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+};
+
 &mmc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc2_8bit_emmc_pins>;
-	vmmc-supply = <&reg_vcc3v3>;
+	vmmc-supply = <&reg_dcdc1>;
 	bus-width = <8>;
 	non-removable;
 	cap-mmc-hw-reset;
@@ -152,6 +191,9 @@ axp81x: pmic@3a3 {
 		reg = <0x3a3>;
 		interrupt-parent = <&r_intc>;
 		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		eldoin-supply = <&reg_dcdc1>;
+		swin-supply = <&reg_dcdc1>;
+		x-powers,drive-vbus-en;
 	};
 
 	ac100: codec@e89 {
@@ -179,22 +221,143 @@ ac100_rtc: rtc {
 	};
 };
 
-&reg_usb1_vbus {
-	gpio = <&pio 3 29 GPIO_ACTIVE_HIGH>; /* PD29 */
-	status = "okay";
+#include "axp81x.dtsi"
+
+&reg_aldo1 {
+	regulator-always-on;
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "vcc-1v8";
+};
+
+&reg_aldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "dram-pll";
+};
+
+&reg_aldo3 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "avcc";
 };
 
-&reg_usb2_vbus {
-	gpio = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
+&reg_dcdc1 {
+	/*
+	 * The schematics say this should be 3.3V, but the FEX file says
+	 * it should be 3V. The latter makes sense, as the WiFi module's
+	 * I/O is indirectly powered from DCDC1, through SW. It is rated
+	 * at 2.98V maximum.
+	 */
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "vcc-3v";
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <700000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-cpua";
+};
+
+&reg_dcdc3 {
+	regulator-always-on;
+	regulator-min-microvolt = <700000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-cpub";
+};
+
+&reg_dcdc4 {
+	regulator-min-microvolt = <700000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-gpu";
+};
+
+&reg_dcdc5 {
+	regulator-always-on;
+	regulator-min-microvolt = <1500000>;
+	regulator-max-microvolt = <1500000>;
+	regulator-name = "vcc-dram";
+};
+
+&reg_dcdc6 {
+	regulator-always-on;
+	regulator-min-microvolt = <900000>;
+	regulator-max-microvolt = <900000>;
+	regulator-name = "vdd-sys";
+};
+
+&reg_dldo2 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "dp-pwr";
+};
+
+&reg_dldo3 {
+	regulator-always-on;
+	regulator-min-microvolt = <2500000>;
+	regulator-max-microvolt = <2500000>;
+	regulator-name = "ephy-io";
+};
+
+&reg_dldo4 {
+	/*
+	 * The PHY requires 20ms after all voltages are applied until core
+	 * logic is ready and 30ms after the reset pin is de-asserted.
+	 * Set a 100ms delay to account for PMIC ramp time and board traces.
+	 */
+	regulator-enable-ramp-delay = <100000>;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "ephy";
+};
+
+&reg_drivevbus {
+	regulator-name = "usb0-vbus";
 	status = "okay";
 };
 
-&reg_vcc3v0 {
-	status = "disabled";
+&reg_eldo1 {
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1200000>;
+	regulator-name = "dp-bridge-1";
+};
+
+&reg_eldo2 {
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1200000>;
+	regulator-name = "dp-bridge-2";
+};
+
+&reg_fldo1 {
+	/* TODO should be handled by USB PHY */
+	regulator-always-on;
+	regulator-min-microvolt = <1080000>;
+	regulator-max-microvolt = <1320000>;
+	regulator-name = "vdd12-hsic";
+};
+
+&reg_fldo2 {
+	/*
+	 * Despite the embedded CPUs core not being used in any way,
+	 * this must remain on or the system will hang.
+	 */
+	regulator-always-on;
+	regulator-min-microvolt = <700000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-cpus";
+};
+
+&reg_rtc_ldo {
+	regulator-name = "vcc-rtc";
 };
 
-&reg_vcc5v0 {
-	status = "disabled";
+&reg_sw {
+	regulator-name = "vcc-wifi-io";
 };
 
 &spdif {

arch/arm/boot/dts/sun8i-a83t-tbs-a711.dts

@@ -43,7 +43,8 @@
 
 /dts-v1/;
 #include "sun8i-a83t.dtsi"
-#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	model = "TBS A711 Tablet";
@@ -105,7 +106,7 @@ &ehci1 {
 };
 
 &mmc0 {
-	vmmc-supply = <&reg_vcc3v3>;
+	vmmc-supply = <&reg_dcdc1>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins>;
 	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
@@ -115,10 +116,8 @@ &mmc0 {
 &mmc1 {
 	mmc-pwrseq = <&wifi_pwrseq>;
 	bus-width = <4>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc1_pins>;
-	vmmc-supply = <&reg_vcc3v3>;
-	vqmmc-supply = <&reg_vcc3v3>;
+	vmmc-supply = <&reg_dldo1>;
+	vqmmc-supply = <&reg_dldo1>;
 	non-removable;
 	wakeup-source;
 	status = "okay";
@@ -135,8 +134,8 @@ brcmf: wifi@1 {
 &mmc2 {
 	pinctrl-0 = <&mmc2_8bit_emmc_pins>;
 	pinctrl-names = "default";
-	vmmc-supply = <&reg_vcc3v3>;
-	vqmmc-supply = <&reg_vcc3v3>;
+	vmmc-supply = <&reg_dcdc1>;
+	vqmmc-supply = <&reg_dcdc1>;
 	bus-width = <8>;
 	non-removable;
 	cap-mmc-hw-reset;
@@ -146,11 +145,12 @@ &mmc2 {
 &r_rsb {
 	status = "okay";
 
-	axp813: pmic@3a3 {
-		compatible = "x-powers,axp813";
+	axp81x: pmic@3a3 {
 		reg = <0x3a3>;
 		interrupt-parent = <&r_intc>;
 		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		swin-supply = <&reg_dcdc1>;
+		x-powers,drive-vbus-en;
 	};
 
 	ac100: codec@e89 {
@@ -179,6 +179,149 @@ ac100_rtc: rtc {
 
 };
 
+#include "axp81x.dtsi"
+
+&reg_aldo1 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "vcc-1.8";
+};
+
+&reg_aldo2 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-always-on;
+	regulator-name = "vdd-drampll";
+};
+
+&reg_aldo3 {
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-always-on;
+	regulator-name = "avcc";
+};
+
+&reg_dcdc1 {
+	regulator-min-microvolt = <3100000>;
+	regulator-max-microvolt = <3100000>;
+	regulator-always-on;
+	regulator-name = "vcc-io";
+};
+
+&reg_dcdc2 {
+	regulator-min-microvolt = <700000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-always-on;
+	regulator-name = "vdd-cpu-A";
+};
+
+&reg_dcdc3 {
+	regulator-min-microvolt = <700000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-always-on;
+	regulator-name = "vdd-cpu-B";
+};
+
+&reg_dcdc4 {
+	regulator-min-microvolt = <700000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-gpu";
+};
+
+&reg_dcdc5 {
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1500000>;
+	regulator-always-on;
+	regulator-name = "vcc-dram";
+};
+
+&reg_dcdc6 {
+	regulator-min-microvolt = <900000>;
+	regulator-max-microvolt = <900000>;
+	regulator-always-on;
+	regulator-name = "vdd-sys";
+};
+
+&reg_dldo1 {
+	regulator-min-microvolt = <3100000>;
+	regulator-max-microvolt = <3100000>;
+	regulator-name = "vcc-wifi-io";
+};
+
+&reg_dldo2 {
+	regulator-min-microvolt = <2800000>;
+	regulator-max-microvolt = <4200000>;
+	regulator-name = "vcc-mipi";
+};
+
+&reg_dldo3 {
+	regulator-min-microvolt = <2800000>;
+	regulator-max-microvolt = <2800000>;
+	regulator-name = "vdd-csi";
+};
+
+&reg_dldo4 {
+	regulator-min-microvolt = <2800000>;
+	regulator-max-microvolt = <2800000>;
+	regulator-name = "avdd-csi";
+};
+
+&reg_drivevbus {
+	regulator-name = "usb0-vbus";
+	status = "okay";
+};
+
+&reg_eldo1 {
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "dvdd-csi-r";
+};
+
+&reg_eldo2 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "vcc-dsi";
+};
+
+&reg_eldo3 {
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "dvdd-csi-f";
+};
+
+&reg_fldo1 {
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1200000>;
+	regulator-name = "vcc-hsic";
+};
+
+&reg_fldo2 {
+	regulator-min-microvolt = <700000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-always-on;
+	regulator-name = "vdd-cpus";
+};
+
+&reg_ldo_io0 {
+	regulator-min-microvolt = <3100000>;
+	regulator-max-microvolt = <3100000>;
+	regulator-name = "vcc-ctp";
+	status = "okay";
+};
+
+&reg_ldo_io1 {
+	regulator-min-microvolt = <3100000>;
+	regulator-max-microvolt = <3100000>;
+	regulator-name = "vcc-vb";
+	status = "okay";
+};
+
+&reg_sw {
+	regulator-min-microvolt = <3100000>;
+	regulator-max-microvolt = <3100000>;
+	regulator-name = "vcc-lcd";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pb_pins>;
@@ -192,8 +335,15 @@ &uart1 {
 	status = "okay";
 };
 
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
 &usbphy {
-	usb1_vbus_supply = <&reg_vcc5v0>;
-	usb2_vbus_supply = <&reg_vcc5v0>;
+	usb0_id_det-gpios = <&pio 7 11 GPIO_ACTIVE_HIGH>; /* PH11 */
+	usb0_vbus-supply = <&reg_drivevbus>;
+	usb1_vbus_supply = <&reg_vmain>;
+	usb2_vbus_supply = <&reg_vmain>;
 	status = "okay";
 };

arch/arm/boot/dts/sun8i-a83t.dtsi

@@ -212,6 +212,8 @@ mmc1: mmc@1c10000 {
 			resets = <&ccu RST_BUS_MMC1>;
 			reset-names = "ahb";
 			interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc1_pins>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;

arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts

@@ -56,6 +56,8 @@ / {
 
 	aliases {
 		serial0 = &uart0;
+		/* ethernet0 is the H3 emac, defined in sun8i-h3.dtsi */
+		ethernet0 = &emac;
 		ethernet1 = &xr819;
 	};
 
@@ -102,6 +104,13 @@ &ehci1 {
 	status = "okay";
 };
 
+&emac {
+	phy-handle = <&int_mii_phy>;
+	phy-mode = "mii";
+	allwinner,leds-active-low;
+	status = "okay";
+};
+
 &mmc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins_a>;

arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts

@@ -52,6 +52,7 @@ / {
 	compatible = "sinovoip,bpi-m2-plus", "allwinner,sun8i-h3";
 
 	aliases {
+		ethernet0 = &emac;
 		serial0 = &uart0;
 		serial1 = &uart1;
 	};
@@ -111,6 +112,24 @@ &ehci2 {
 	status = "okay";
 };
 
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emac_rgmii_pins>;
+	phy-supply = <&reg_gmac_3v3>;
+	phy-handle = <&ext_rgmii_phy>;
+	phy-mode = "rgmii";
+
+	allwinner,leds-active-low;
+	status = "okay";
+};
+
+&external_mdio {
+	ext_rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
 &ir {
 	pinctrl-names = "default";
 	pinctrl-0 = <&ir_pins_a>;

arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts

@@ -51,6 +51,16 @@ aliases {
 		ethernet1 = &sdio_wifi;
 	};
 
+	reg_gmac_3v3: gmac-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "gmac-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <100000>;
+		enable-active-high;
+		gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
+	};
+
 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		pinctrl-names = "default";
@@ -66,6 +76,25 @@ &ehci2 {
 	status = "okay";
 };
 
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emac_rgmii_pins>;
+	phy-supply = <&reg_gmac_3v3>;
+	phy-handle = <&ext_rgmii_phy>;
+	phy-mode = "rgmii";
+
+	allwinner,leds-active-low;
+
+	status = "okay";
+};
+
+&external_mdio {
+	ext_rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <7>;
+	};
+};
+
 &ir {
 	pinctrl-names = "default";
 	pinctrl-0 = <&ir_pins_a>;

arch/arm/boot/dts/sun8i-h3-nanopi-neo.dts

@@ -46,3 +46,10 @@ / {
 	model = "FriendlyARM NanoPi NEO";
 	compatible = "friendlyarm,nanopi-neo", "allwinner,sun8i-h3";
 };
+
+&emac {
+	phy-handle = <&int_mii_phy>;
+	phy-mode = "mii";
+	allwinner,leds-active-low;
+	status = "okay";
+};

arch/arm/boot/dts/sun8i-h3-orangepi-2.dts

@@ -54,6 +54,7 @@ / {
 	aliases {
 		serial0 = &uart0;
 		/* ethernet0 is the H3 emac, defined in sun8i-h3.dtsi */
+		ethernet0 = &emac;
 		ethernet1 = &rtl8189;
 	};
 
@@ -117,6 +118,13 @@ &ehci1 {
 	status = "okay";
 };
 
+&emac {
+	phy-handle = <&int_mii_phy>;
+	phy-mode = "mii";
+	allwinner,leds-active-low;
+	status = "okay";
+};
+
 &ir {
 	pinctrl-names = "default";
 	pinctrl-0 = <&ir_pins_a>;

arch/arm/boot/dts/sun8i-h3-orangepi-one.dts

@@ -52,6 +52,7 @@ / {
 	compatible = "xunlong,orangepi-one", "allwinner,sun8i-h3";
 
 	aliases {
+		ethernet0 = &emac;
 		serial0 = &uart0;
 	};
 
@@ -97,6 +98,13 @@ &ehci1 {
 	status = "okay";
 };
 
+&emac {
+	phy-handle = <&int_mii_phy>;
+	phy-mode = "mii";
+	allwinner,leds-active-low;
+	status = "okay";
+};
+
 &mmc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;

arch/arm/boot/dts/sun8i-h3-orangepi-pc-plus.dts

@@ -53,6 +53,11 @@ aliases {
 	};
 };
 
+&emac {
+	/* LEDs changed to active high on the plus */
+	/delete-property/ allwinner,leds-active-low;
+};
+
 &mmc1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc1_pins_a>;

arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts

@@ -52,6 +52,7 @@ / {
 	compatible = "xunlong,orangepi-pc", "allwinner,sun8i-h3";
 
 	aliases {
+		ethernet0 = &emac;
 		serial0 = &uart0;
 	};
 
@@ -113,6 +114,13 @@ &ehci3 {
 	status = "okay";
 };
 
+&emac {
+	phy-handle = <&int_mii_phy>;
+	phy-mode = "mii";
+	allwinner,leds-active-low;
+	status = "okay";
+};
+
 &ir {
 	pinctrl-names = "default";
 	pinctrl-0 = <&ir_pins_a>;

arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts

@@ -47,6 +47,10 @@ / {
 	model = "Xunlong Orange Pi Plus / Plus 2";
 	compatible = "xunlong,orangepi-plus", "allwinner,sun8i-h3";
 
+	aliases {
+		ethernet0 = &emac;
+	};
+
 	reg_gmac_3v3: gmac-3v3 {
 		compatible = "regulator-fixed";
 		regulator-name = "gmac-3v3";
@@ -74,6 +78,24 @@ &ehci3 {
 	status = "okay";
 };
 
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emac_rgmii_pins>;
+	phy-supply = <&reg_gmac_3v3>;
+	phy-handle = <&ext_rgmii_phy>;
+	phy-mode = "rgmii";
+
+	allwinner,leds-active-low;
+	status = "okay";
+};
+
+&external_mdio {
+	ext_rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
 &mmc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc2_8bit_pins>;

arch/arm/boot/dts/sun8i-h3-orangepi-plus2e.dts

@@ -61,3 +61,19 @@ reg_gmac_3v3: gmac-3v3 {
 		gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; /* PD6 */
 	};
 };
+
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emac_rgmii_pins>;
+	phy-supply = <&reg_gmac_3v3>;
+	phy-handle = <&ext_rgmii_phy>;
+	phy-mode = "rgmii";
+	status = "okay";
+};
+
+&external_mdio {
+	ext_rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};

arch/arm/boot/dts/sunxi-h3-h5.dtsi

@@ -396,6 +396,55 @@ timer@1c20c00 {
 			clocks = <&osc24M>;
 		};
 
+		emac: ethernet@1c30000 {
+			compatible = "allwinner,sun8i-h3-emac";
+			syscon = <&syscon>;
+			reg = <0x01c30000 0x10000>;
+			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+			resets = <&ccu RST_BUS_EMAC>;
+			reset-names = "stmmaceth";
+			clocks = <&ccu CLK_BUS_EMAC>;
+			clock-names = "stmmaceth";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			mdio: mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "snps,dwmac-mdio";
+			};
+
+			mdio-mux {
+				compatible = "allwinner,sun8i-h3-mdio-mux";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				mdio-parent-bus = <&mdio>;
+				/* Only one MDIO is usable at the time */
+				internal_mdio: mdio@1 {
+					compatible = "allwinner,sun8i-h3-mdio-internal";
+					reg = <1>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					int_mii_phy: ethernet-phy@1 {
+						compatible = "ethernet-phy-ieee802.3-c22";
+						reg = <1>;
+						clocks = <&ccu CLK_BUS_EPHY>;
+						resets = <&ccu RST_BUS_EPHY>;
+					};
+				};
+
+				external_mdio: mdio@2 {
+					reg = <2>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+			};
+		};
+
 		spi0: spi@1c68000 {
 			compatible = "allwinner,sun8i-h3-spi";
 			reg = <0x01c68000 0x1000>;

arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo2.dts

@@ -50,6 +50,7 @@ / {
 	compatible = "friendlyarm,nanopi-neo2", "allwinner,sun50i-h5";
 
 	aliases {
+		ethernet0 = &emac;
 		serial0 = &uart0;
 	};
 
@@ -108,6 +109,22 @@ &ehci3 {
 	status = "okay";
 };
 
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emac_rgmii_pins>;
+	phy-supply = <&reg_gmac_3v3>;
+	phy-handle = <&ext_rgmii_phy>;
+	phy-mode = "rgmii";
+	status = "okay";
+};
+
+&external_mdio {
+	ext_rgmii_phy: ethernet-phy@7 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <7>;
+	};
+};
+
 &mmc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;

arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts

@@ -59,6 +59,7 @@ reg_vcc3v3: vcc3v3 {
 	};
 
 	aliases {
+		ethernet0 = &emac;
 		serial0 = &uart0;
 	};
 
@@ -136,6 +137,22 @@ &ehci3 {
 	status = "okay";
 };
 
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emac_rgmii_pins>;
+	phy-supply = <&reg_gmac_3v3>;
+	phy-handle = <&ext_rgmii_phy>;
+	phy-mode = "rgmii";
+	status = "okay";
+};
+
+&external_mdio {
+	ext_rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
 &ir {
 	pinctrl-names = "default";
 	pinctrl-0 = <&ir_pins_a>;

arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts

@@ -54,6 +54,7 @@ / {
 	compatible = "xunlong,orangepi-prime", "allwinner,sun50i-h5";
 
 	aliases {
+		ethernet0 = &emac;
 		serial0 = &uart0;
 	};
 
@@ -143,6 +144,22 @@ &ehci3 {
 	status = "okay";
 };
 
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emac_rgmii_pins>;
+	phy-supply = <&reg_gmac_3v3>;
+	phy-handle = <&ext_rgmii_phy>;
+	phy-mode = "rgmii";
+	status = "okay";
+};
+
+&external_mdio {
+	ext_rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
 &ir {
 	pinctrl-names = "default";
 	pinctrl-0 = <&ir_pins_a>;