Commit 0c2bec96 authored by Mike Rapoport's avatar Mike Rapoport Committed by John W. Linville

libertas: if_spi: add ability to call board specific setup/teardown methods

In certain cases it is required to perform board specific actions
before activating libertas G-SPI interface. These actions may include
power up of the chip, GPIOs setup, proper pin-strapping and SPI
controller config.
This patch adds ability to call board specific setup/teardown methods
Signed-off-by: default avatarMike Rapoport <mike@compulab.co.il>
Acked-by: default avatarAndrey Yurovsky <andrey@cozybit.com>
Acked-by: default avatarDan Williams <dcbw@redhat.com>
Signed-off-by: default avatarJohn W. Linville <linville@tuxdriver.com>
parent d43e8786
...@@ -42,6 +42,7 @@ struct if_spi_packet { ...@@ -42,6 +42,7 @@ struct if_spi_packet {
struct if_spi_card { struct if_spi_card {
struct spi_device *spi; struct spi_device *spi;
struct lbs_private *priv; struct lbs_private *priv;
struct libertas_spi_platform_data *pdata;
char helper_fw_name[FIRMWARE_NAME_MAX]; char helper_fw_name[FIRMWARE_NAME_MAX];
char main_fw_name[FIRMWARE_NAME_MAX]; char main_fw_name[FIRMWARE_NAME_MAX];
...@@ -1022,6 +1023,17 @@ static int __devinit if_spi_probe(struct spi_device *spi) ...@@ -1022,6 +1023,17 @@ static int __devinit if_spi_probe(struct spi_device *spi)
lbs_deb_enter(LBS_DEB_SPI); lbs_deb_enter(LBS_DEB_SPI);
if (!pdata) {
err = -EINVAL;
goto out;
}
if (pdata->setup) {
err = pdata->setup(spi);
if (err)
goto out;
}
/* Allocate card structure to represent this specific device */ /* Allocate card structure to represent this specific device */
card = kzalloc(sizeof(struct if_spi_card), GFP_KERNEL); card = kzalloc(sizeof(struct if_spi_card), GFP_KERNEL);
if (!card) { if (!card) {
...@@ -1029,6 +1041,7 @@ static int __devinit if_spi_probe(struct spi_device *spi) ...@@ -1029,6 +1041,7 @@ static int __devinit if_spi_probe(struct spi_device *spi)
goto out; goto out;
} }
spi_set_drvdata(spi, card); spi_set_drvdata(spi, card);
card->pdata = pdata;
card->spi = spi; card->spi = spi;
card->gpio_cs = pdata->gpio_cs; card->gpio_cs = pdata->gpio_cs;
card->prev_xfer_time = jiffies; card->prev_xfer_time = jiffies;
...@@ -1158,6 +1171,8 @@ static int __devexit libertas_spi_remove(struct spi_device *spi) ...@@ -1158,6 +1171,8 @@ static int __devexit libertas_spi_remove(struct spi_device *spi)
if_spi_terminate_spi_thread(card); if_spi_terminate_spi_thread(card);
lbs_remove_card(priv); /* will call free_netdev */ lbs_remove_card(priv); /* will call free_netdev */
gpio_free(card->gpio_cs); gpio_free(card->gpio_cs);
if (card->pdata->teardown)
card->pdata->teardown(spi);
free_if_spi_card(card); free_if_spi_card(card);
lbs_deb_leave(LBS_DEB_SPI); lbs_deb_leave(LBS_DEB_SPI);
return 0; return 0;
......
...@@ -10,6 +10,9 @@ ...@@ -10,6 +10,9 @@
*/ */
#ifndef _LIBERTAS_SPI_H_ #ifndef _LIBERTAS_SPI_H_
#define _LIBERTAS_SPI_H_ #define _LIBERTAS_SPI_H_
struct spi_device;
struct libertas_spi_platform_data { struct libertas_spi_platform_data {
/* There are two ways to read data from the WLAN module's SPI /* There are two ways to read data from the WLAN module's SPI
* interface. Setting 0 or 1 here controls which one is used. * interface. Setting 0 or 1 here controls which one is used.
...@@ -21,5 +24,9 @@ struct libertas_spi_platform_data { ...@@ -21,5 +24,9 @@ struct libertas_spi_platform_data {
/* GPIO number to use as chip select */ /* GPIO number to use as chip select */
u16 gpio_cs; u16 gpio_cs;
/* Board specific setup/teardown */
int (*setup)(struct spi_device *spi);
int (*teardown)(struct spi_device *spi);
}; };
#endif #endif
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment