Commit 0d928b0b authored by Uwe Kleine-König's avatar Uwe Kleine-König

Complete irq tracing support for ARM

Before this patch enabling and disabling irqs in assembler code and by
the hardware wasn't tracked completly.

I had to transpose two instructions in arch/arm/lib/bitops.h because
restore_irqs doesn't preserve the flags with CONFIG_TRACE_IRQFLAGS=y
Signed-off-by: default avatarUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@redhat.com>
Signed-off-by: default avatarUwe Kleine-König <u.kleine-koenig@pengutronix.de>
parent 181f817e
......@@ -74,23 +74,56 @@
* Enable and disable interrupts
*/
#if __LINUX_ARM_ARCH__ >= 6
.macro disable_irq
.macro disable_irq_notrace
cpsid i
.endm
.macro enable_irq
.macro enable_irq_notrace
cpsie i
.endm
#else
.macro disable_irq
.macro disable_irq_notrace
msr cpsr_c, #PSR_I_BIT | SVC_MODE
.endm
.macro enable_irq
.macro enable_irq_notrace
msr cpsr_c, #SVC_MODE
.endm
#endif
.macro asm_trace_hardirqs_off
#if defined(CONFIG_TRACE_IRQFLAGS)
stmdb sp!, {r0-r3, ip, lr}
bl trace_hardirqs_off
ldmia sp!, {r0-r3, ip, lr}
#endif
.endm
.macro asm_trace_hardirqs_on_cond, cond
#if defined(CONFIG_TRACE_IRQFLAGS)
/*
* actually the registers should be pushed and pop'd conditionally, but
* after bl the flags are certainly clobbered
*/
stmdb sp!, {r0-r3, ip, lr}
bl\cond trace_hardirqs_on
ldmia sp!, {r0-r3, ip, lr}
#endif
.endm
.macro asm_trace_hardirqs_on
asm_trace_hardirqs_on_cond al
.endm
.macro disable_irq
disable_irq_notrace
asm_trace_hardirqs_off
.endm
.macro enable_irq
asm_trace_hardirqs_on
enable_irq_notrace
.endm
/*
* Save the current IRQ state and disable IRQs. Note that this macro
* assumes FIQs are enabled, and that the processor is in SVC mode.
......@@ -104,10 +137,16 @@
* Restore interrupt state previously stored in a register. We don't
* guarantee that this will preserve the flags.
*/
.macro restore_irqs, oldcpsr
.macro restore_irqs_notrace, oldcpsr
msr cpsr_c, \oldcpsr
.endm
.macro restore_irqs, oldcpsr
tst \oldcpsr, #PSR_I_BIT
asm_trace_hardirqs_on_cond eq
restore_irqs_notrace \oldcpsr
.endm
#define USER(x...) \
9999: x; \
.section __ex_table,"a"; \
......
......@@ -151,6 +151,8 @@ ENDPROC(__und_invalid)
@ r4 - orig_r0 (see pt_regs definition in ptrace.h)
@
stmia r5, {r0 - r4}
asm_trace_hardirqs_off
.endm
.align 5
......@@ -206,9 +208,6 @@ ENDPROC(__dabt_svc)
__irq_svc:
svc_entry
#ifdef CONFIG_TRACE_IRQFLAGS
bl trace_hardirqs_off
#endif
#ifdef CONFIG_PREEMPT
get_thread_info tsk
ldr r8, [tsk, #TI_PREEMPT] @ get preempt count
......@@ -383,6 +382,8 @@ ENDPROC(__pabt_svc)
@ Clear FP to mark the first stack frame
@
zero_fp
asm_trace_hardirqs_off
.endm
.macro kuser_cmpxchg_check
......@@ -437,9 +438,6 @@ __irq_usr:
usr_entry
kuser_cmpxchg_check
#ifdef CONFIG_TRACE_IRQFLAGS
bl trace_hardirqs_off
#endif
get_thread_info tsk
#ifdef CONFIG_PREEMPT
ldr r8, [tsk, #TI_PREEMPT] @ get preempt count
......
......@@ -60,8 +60,8 @@
tst r2, r0, lsl r3
\instr r2, r2, r0, lsl r3
\store r2, [r1]
restore_irqs ip
moveq r0, #0
restore_irqs ip
mov pc, lr
.endm
#endif
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment