Commit 0dd3c781 authored by dmitry pervushin's avatar dmitry pervushin Committed by Jeff Garzik

[PATCH] cs89x0.c: support for Philips' pnx0105 network adapter

This patch is to provide support for cs89x0-based network device on
Philips' pnx0105 board.
Signed-off-by: default avatardmitry pervushin <dpervushin@ru.mvista.com>
Signed-off-by: default avatarAndrew Morton <akpm@osdl.org>
parent 7aa55fce
......@@ -1320,7 +1320,7 @@ config FORCEDETH
config CS89x0
tristate "CS89x0 support"
depends on NET_PCI && (ISA || ARCH_IXDP2X01)
depends on (NET_PCI && (ISA || ARCH_IXDP2X01)) || ARCH_PNX0105
---help---
Support for CS89x0 chipset based Ethernet cards. If you have a
network (Ethernet) card of this type, say Y and read the
......
......@@ -174,6 +174,13 @@ static unsigned int cs8900_irq_map[] = {1,0,0,0};
#include <asm/irq.h>
static unsigned int netcard_portlist[] __initdata = {IXDP2X01_CS8900_VIRT_BASE, 0};
static unsigned int cs8900_irq_map[] = {IRQ_IXDP2X01_CS8900, 0, 0, 0};
#elif defined(CONFIG_ARCH_PNX0105)
#include <asm/irq.h>
#include <asm/arch/gpio.h>
#define CIRRUS_DEFAULT_BASE IO_ADDRESS(EXT_STATIC2_s0_BASE + 0x200000) /* = Physical address 0x48200000 */
#define CIRRUS_DEFAULT_IRQ VH_INTC_INT_NUM_CASCADED_INTERRUPT_1 /* Event inputs bank 1 - ID 35/bit 3 */
static unsigned int netcard_portlist[] __initdata = {CIRRUS_DEFAULT_BASE, 0};
static unsigned int cs8900_irq_map[] = {CIRRUS_DEFAULT_IRQ, 0, 0, 0};
#else
static unsigned int netcard_portlist[] __initdata =
{ 0x300, 0x320, 0x340, 0x360, 0x200, 0x220, 0x240, 0x260, 0x280, 0x2a0, 0x2c0, 0x2e0, 0};
......@@ -431,6 +438,30 @@ cs89x0_probe1(struct net_device *dev, int ioaddr, int modular)
#endif
}
#ifdef CONFIG_ARCH_PNX0105
initialize_ebi();
/* Map GPIO registers for the pins connected to the CS8900a. */
if (map_cirrus_gpio() < 0)
return -ENODEV;
reset_cirrus();
/* Map event-router registers. */
if (map_event_router() < 0)
return -ENODEV;
enable_cirrus_irq();
unmap_cirrus_gpio();
unmap_event_router();
dev->base_addr = ioaddr;
for (i = 0 ; i < 3 ; i++)
readreg(dev, 0);
#endif
/* Grab the region so we can find another board if autoIRQ fails. */
/* WTF is going on here? */
if (!request_region(ioaddr & ~3, NETCARD_IO_EXTENT, DRV_NAME)) {
......@@ -672,7 +703,7 @@ printk("PP_addr=0x%x\n", inw(ioaddr + ADD_PORT));
} else {
i = lp->isa_config & INT_NO_MASK;
if (lp->chip_type == CS8900) {
#ifdef CONFIG_ARCH_IXDP2X01
#if defined(CONFIG_ARCH_IXDP2X01) || defined(CONFIG_ARCH_PNX0105)
i = cs8900_irq_map[0];
#else
/* Translate the IRQ using the IRQ mapping table. */
......@@ -1145,7 +1176,7 @@ net_open(struct net_device *dev)
int i;
int ret;
#ifndef CONFIG_SH_HICOSH4 /* uses irq#1, so this won't work */
#if !defined(CONFIG_SH_HICOSH4) && !defined(CONFIG_ARCH_PNX0105) /* uses irq#1, so this won't work */
if (dev->irq < 2) {
/* Allow interrupts to be generated by the chip */
/* Cirrus' release had this: */
......@@ -1176,7 +1207,7 @@ net_open(struct net_device *dev)
else
#endif
{
#ifndef CONFIG_ARCH_IXDP2X01
#if !defined(CONFIG_ARCH_IXDP2X01) && !defined(CONFIG_ARCH_PNX0105)
if (((1 << dev->irq) & lp->irq_map) == 0) {
printk(KERN_ERR "%s: IRQ %d is not in our map of allowable IRQs, which is %x\n",
dev->name, dev->irq, lp->irq_map);
......@@ -1261,6 +1292,9 @@ net_open(struct net_device *dev)
case A_CNF_MEDIA_10B_2: result = lp->adapter_cnf & A_CNF_10B_2; break;
default: result = lp->adapter_cnf & (A_CNF_10B_T | A_CNF_AUI | A_CNF_10B_2);
}
#ifdef CONFIG_ARCH_PNX0105
result = A_CNF_10B_T;
#endif
if (!result) {
printk(KERN_ERR "%s: EEPROM is configured for unavailable media\n", dev->name);
release_irq:
......
......@@ -16,7 +16,7 @@
#include <linux/config.h>
#ifdef CONFIG_ARCH_IXDP2X01
#if defined(CONFIG_ARCH_IXDP2X01) || defined(CONFIG_ARCH_PNX0105)
/* IXDP2401/IXDP2801 uses dword-aligned register addressing */
#define CS89x0_PORT(reg) ((reg) * 2)
#else
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment