SERIAL: 8250: Remove SERIAL_8250_AU1X00

Remove the SERIAL_8250_AU1X00 config symbol.  Instead, use the MIPS_ALCHEMY
one which is always defined when building an Au1x00-based platform.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Linux-serial <linux-serial@vger.kernel.org>
Patchwork: https://patchwork.linux-mips.org/patch/1461/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This one depends on a previous patch (which removes SOC_AU1X00 and changes
MACH_ALCHEMY) to apply cleanly (and then actually work), so I'd love for
this to go in via the mips tree.

arch/mips/alchemy/common/platform.c

@@ -33,7 +33,6 @@
 	}
 
 static struct plat_serial8250_port au1x00_uart_data[] = {
-#if defined(CONFIG_SERIAL_8250_AU1X00)
 #if defined(CONFIG_SOC_AU1000)
 	PORT(UART0_PHYS_ADDR, AU1000_UART0_INT),
 	PORT(UART1_PHYS_ADDR, AU1000_UART1_INT),
@@ -54,7 +53,6 @@ static struct plat_serial8250_port au1x00_uart_data[] = {
 	PORT(UART0_PHYS_ADDR, AU1200_UART0_INT),
 	PORT(UART1_PHYS_ADDR, AU1200_UART1_INT),
 #endif
-#endif	/* CONFIG_SERIAL_8250_AU1X00 */
 	{ },
 };
 

drivers/serial/8250.c

@@ -302,7 +302,7 @@ static const struct serial8250_config uart_config[] = {
 	},
 };
 
-#if defined (CONFIG_SERIAL_8250_AU1X00)
+#if defined(CONFIG_MIPS_ALCHEMY)
 
 /* Au1x00 UART hardware has a weird register layout */
 static const u8 au_io_in_map[] = {
@@ -422,7 +422,6 @@ static unsigned int mem32_serial_in(struct uart_port *p, int offset)
 	return readl(p->membase + offset);
 }
 
-#ifdef CONFIG_SERIAL_8250_AU1X00
 static unsigned int au_serial_in(struct uart_port *p, int offset)
 {
 	offset = map_8250_in_reg(p, offset) << p->regshift;
@@ -434,7 +433,6 @@ static void au_serial_out(struct uart_port *p, int offset, int value)
 	offset = map_8250_out_reg(p, offset) << p->regshift;
 	__raw_writel(value, p->membase + offset);
 }
-#endif
 
 static unsigned int tsi_serial_in(struct uart_port *p, int offset)
 {
@@ -503,12 +501,11 @@ static void set_io_from_upio(struct uart_port *p)
 		p->serial_out = mem32_serial_out;
 		break;
 
-#ifdef CONFIG_SERIAL_8250_AU1X00
 	case UPIO_AU:
 		p->serial_in = au_serial_in;
 		p->serial_out = au_serial_out;
 		break;
-#endif
+
 	case UPIO_TSI:
 		p->serial_in = tsi_serial_in;
 		p->serial_out = tsi_serial_out;
@@ -535,9 +532,7 @@ serial_out_sync(struct uart_8250_port *up, int offset, int value)
 	switch (p->iotype) {
 	case UPIO_MEM:
 	case UPIO_MEM32:
-#ifdef CONFIG_SERIAL_8250_AU1X00
 	case UPIO_AU:
-#endif
 	case UPIO_DWAPB:
 		p->serial_out(p, offset, value);
 		p->serial_in(p, UART_LCR);	/* safe, no side-effects */
@@ -573,7 +568,7 @@ static inline void _serial_dl_write(struct uart_8250_port *up, int value)
 	serial_outp(up, UART_DLM, value >> 8 & 0xff);
 }
 
-#if defined(CONFIG_SERIAL_8250_AU1X00)
+#if defined(CONFIG_MIPS_ALCHEMY)
 /* Au1x00 haven't got a standard divisor latch */
 static int serial_dl_read(struct uart_8250_port *up)
 {
@@ -2596,11 +2591,9 @@ static void serial8250_config_port(struct uart_port *port, int flags)
 	if (flags & UART_CONFIG_TYPE)
 		autoconfig(up, probeflags);
 
-#ifdef CONFIG_SERIAL_8250_AU1X00
 	/* if access method is AU, it is a 16550 with a quirk */
 	if (up->port.type == PORT_16550A && up->port.iotype == UPIO_AU)
 		up->bugs |= UART_BUG_NOMSR;
-#endif
 
 	if (up->port.type != PORT_UNKNOWN && flags & UART_CONFIG_IRQ)
 		autoconfig_irq(up);

drivers/serial/Kconfig

@@ -258,14 +258,6 @@ config SERIAL_8250_ACORN
 	  system, say Y to this option.  The driver can handle 1, 2, or 3 port
 	  cards.  If unsure, say N.
 
-config SERIAL_8250_AU1X00
-	bool "Au1x00 serial port support"
-	depends on SERIAL_8250 != n && MIPS_ALCHEMY
-	help
-	  If you have an Au1x00 SOC based board and want to use the serial port,
-	  say Y to this option. The driver can handle up to 4 serial ports,
-	  depending on the SOC. If unsure, say N.
-
 config SERIAL_8250_RM9K
 	bool "Support for MIPS RM9xxx integrated serial port"
 	depends on SERIAL_8250 != n && SERIAL_RM9000