usb: misc: EHSET Test Fixture device driver for host compliance

An Embedded Host High-Speed Electrical Test (EHSET) test fixture is
used to initiate test modes on a host controller in order to perform
the high speed electrical testing procedure for USB-IF compliance.
When this test fixture is connected to a host, it can enumerate as
one of several selectable VID/PID pairs, each corresponding to one
of the following test modes:

* TEST_SE0_NAK
* TEST_J
* TEST_K
* TEST_PACKET
* HS_HOST_PORT_SUSPEND_RESUME
* SINGLE_STEP_GET_DEV_DESC
* SINGLE_STEP_SET_FEATURE

The USB EHSET procedure can be found here:
http://www.usb.org/developers/onthego/EHSET_v1.01.pdfSigned-off-by: Manu Gautam <mgautam@codeaurora.org>
[jackp@codeaurora.org: imported from commit 073c9409 on codeaurora.org;
 minor cleanup and updated author email]
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/usb/misc/Kconfig

@@ -200,6 +200,19 @@ config USB_TEST
 	  See <http://www.linux-usb.org/usbtest/> for more information,
 	  including sample test device firmware and "how to use it".
 
+config USB_EHSET_TEST_FIXTURE
+        tristate "USB EHSET Test Fixture driver"
+        help
+	  Say Y here if you want to support the special test fixture device
+	  used for the USB-IF Embedded Host High-Speed Electrical Test procedure.
+
+	  When the test fixture is connected, it can enumerate as one of several
+	  VID/PID pairs. This driver then initiates a corresponding test mode on
+	  the downstream port to which the test fixture is attached.
+
+	  See <http://www.usb.org/developers/onthego/EHSET_v1.01.pdf> for more
+	  information.
+
 config USB_ISIGHTFW
 	tristate "iSight firmware loading support"
 	select FW_LOADER

drivers/usb/misc/Makefile

@@ -19,6 +19,7 @@ obj-$(CONFIG_USB_LED)			+= usbled.o
 obj-$(CONFIG_USB_LEGOTOWER)		+= legousbtower.o
 obj-$(CONFIG_USB_RIO500)		+= rio500.o
 obj-$(CONFIG_USB_TEST)			+= usbtest.o
+obj-$(CONFIG_USB_EHSET_TEST_FIXTURE)    += ehset.o
 obj-$(CONFIG_USB_TRANCEVIBRATOR)	+= trancevibrator.o
 obj-$(CONFIG_USB_USS720)		+= uss720.o
 obj-$(CONFIG_USB_SEVSEG)		+= usbsevseg.o

drivers/usb/misc/ehset.c

+/*
+ * Copyright (c) 2010-2013, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/usb.h>
+#include <linux/usb/ch11.h>
+
+#define TEST_SE0_NAK_PID			0x0101
+#define TEST_J_PID				0x0102
+#define TEST_K_PID				0x0103
+#define TEST_PACKET_PID				0x0104
+#define TEST_HS_HOST_PORT_SUSPEND_RESUME	0x0106
+#define TEST_SINGLE_STEP_GET_DEV_DESC		0x0107
+#define TEST_SINGLE_STEP_SET_FEATURE		0x0108
+
+static int ehset_probe(struct usb_interface *intf,
+		       const struct usb_device_id *id)
+{
+	int ret = -EINVAL;
+	struct usb_device *dev = interface_to_usbdev(intf);
+	struct usb_device *hub_udev = dev->parent;
+	struct usb_device_descriptor *buf;
+	u8 portnum = dev->portnum;
+	u16 test_pid = le16_to_cpu(dev->descriptor.idProduct);
+
+	switch (test_pid) {
+	case TEST_SE0_NAK_PID:
+		ret = usb_control_msg(hub_udev, usb_sndctrlpipe(hub_udev, 0),
+					USB_REQ_SET_FEATURE, USB_RT_PORT,
+					USB_PORT_FEAT_TEST,
+					(TEST_SE0_NAK << 8) | portnum,
+					NULL, 0, 1000);
+		break;
+	case TEST_J_PID:
+		ret = usb_control_msg(hub_udev, usb_sndctrlpipe(hub_udev, 0),
+					USB_REQ_SET_FEATURE, USB_RT_PORT,
+					USB_PORT_FEAT_TEST,
+					(TEST_J << 8) | portnum,
+					NULL, 0, 1000);
+		break;
+	case TEST_K_PID:
+		ret = usb_control_msg(hub_udev, usb_sndctrlpipe(hub_udev, 0),
+					USB_REQ_SET_FEATURE, USB_RT_PORT,
+					USB_PORT_FEAT_TEST,
+					(TEST_K << 8) | portnum,
+					NULL, 0, 1000);
+		break;
+	case TEST_PACKET_PID:
+		ret = usb_control_msg(hub_udev, usb_sndctrlpipe(hub_udev, 0),
+					USB_REQ_SET_FEATURE, USB_RT_PORT,
+					USB_PORT_FEAT_TEST,
+					(TEST_PACKET << 8) | portnum,
+					NULL, 0, 1000);
+		break;
+	case TEST_HS_HOST_PORT_SUSPEND_RESUME:
+		/* Test: wait for 15secs -> suspend -> 15secs delay -> resume */
+		msleep(15 * 1000);
+		ret = usb_control_msg(hub_udev, usb_sndctrlpipe(hub_udev, 0),
+					USB_REQ_SET_FEATURE, USB_RT_PORT,
+					USB_PORT_FEAT_SUSPEND, portnum,
+					NULL, 0, 1000);
+		if (ret < 0)
+			break;
+
+		msleep(15 * 1000);
+		ret = usb_control_msg(hub_udev, usb_sndctrlpipe(hub_udev, 0),
+					USB_REQ_CLEAR_FEATURE, USB_RT_PORT,
+					USB_PORT_FEAT_SUSPEND, portnum,
+					NULL, 0, 1000);
+		break;
+	case TEST_SINGLE_STEP_GET_DEV_DESC:
+		/* Test: wait for 15secs -> GetDescriptor request */
+		msleep(15 * 1000);
+		buf = kmalloc(USB_DT_DEVICE_SIZE, GFP_KERNEL);
+		if (!buf)
+			return -ENOMEM;
+
+		ret = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0),
+					USB_REQ_GET_DESCRIPTOR, USB_DIR_IN,
+					USB_DT_DEVICE << 8, 0,
+					buf, USB_DT_DEVICE_SIZE,
+					USB_CTRL_GET_TIMEOUT);
+		kfree(buf);
+		break;
+	case TEST_SINGLE_STEP_SET_FEATURE:
+		/* unsupported for now */
+	default:
+		dev_err(&intf->dev, "%s: unsupported PID: 0x%x\n",
+			__func__, test_pid);
+	}
+
+	return (ret < 0) ? ret : 0;
+}
+
+static void ehset_disconnect(struct usb_interface *intf)
+{
+}
+
+static const struct usb_device_id ehset_id_table[] = {
+	{ USB_DEVICE(0x1a0a, TEST_SE0_NAK_PID) },
+	{ USB_DEVICE(0x1a0a, TEST_J_PID) },
+	{ USB_DEVICE(0x1a0a, TEST_K_PID) },
+	{ USB_DEVICE(0x1a0a, TEST_PACKET_PID) },
+	{ USB_DEVICE(0x1a0a, TEST_HS_HOST_PORT_SUSPEND_RESUME) },
+	{ USB_DEVICE(0x1a0a, TEST_SINGLE_STEP_GET_DEV_DESC) },
+	{ USB_DEVICE(0x1a0a, TEST_SINGLE_STEP_SET_FEATURE) },
+	{ }			/* Terminating entry */
+};
+MODULE_DEVICE_TABLE(usb, ehset_id_table);
+
+static struct usb_driver ehset_driver = {
+	.name =		"usb_ehset_test",
+	.probe =	ehset_probe,
+	.disconnect =	ehset_disconnect,
+	.id_table =	ehset_id_table,
+};
+
+module_usb_driver(ehset_driver);
+
+MODULE_DESCRIPTION("USB Driver for EHSET Test Fixture");
+MODULE_LICENSE("GPL v2");