Commit 168e0461 authored by Lothar Waßmann's avatar Lothar Waßmann Committed by Shawn Guo

ARM: dts: imx6: add support for more Ka-Ro electronics modules

Add support for the following i.MX6 based modules from Ka-Ro
electronics GmbH:
TX6S-8034:
Processor    Freescale i.MX 6 Solo, 800MHz
RAM          256MiB DDR3 SDRAM
ROM          128MiB NAND Flash
Power supply Single 3.1V to 5.5V
Size         31mm SO-DIMM
Temp. Range  industrial grade (-40°C/-25°C to 105°C Tj)

TX6S-8035:
Processor    Freescale i.MX 6 Solo, 800MHz
RAM          512MiB DDR3 SDRAM
ROM          4GiB eMMC
Power supply Single 3.1V to 5.5V
Size         31mm SO-DIMM
Temp. Range  industrial grade (-40°C/-25°C to 105°C Tj)

TX6U-8033:
Processor    Freescale i.MX 6 Dual Lite, 800MHz
RAM          1GiB DDR3 SDRAM
ROM          4GiB eMMC
Power supply Single 3.1V to 5.5V
Size         31mm SO-DIMM
Temp. Range  industrial grade (-40°C/-25°C to 105°C Tj)

TX6Q-1036:
Processor    Freescale i.MX 6Quad, 1GHz
RAM          1GB DDR3 SDRAM 64-bit
ROM          8GiB eMMC
Power supply Single 3.1V to 5.5V
Size         31mm SO-DIMM
Temp. Range  Extended Consumer Grade (-20°C to 105°C Tj)
Signed-off-by: default avatarLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: default avatarShawn Guo <shawnguo@kernel.org>
parent 720f4340
...@@ -320,7 +320,10 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ ...@@ -320,7 +320,10 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-sabrelite.dtb \ imx6dl-sabrelite.dtb \
imx6dl-sabresd.dtb \ imx6dl-sabresd.dtb \
imx6dl-tx6dl-comtft.dtb \ imx6dl-tx6dl-comtft.dtb \
imx6dl-tx6s-8034.dtb \
imx6dl-tx6s-8035.dtb \
imx6dl-tx6u-801x.dtb \ imx6dl-tx6u-801x.dtb \
imx6dl-tx6u-8033.dtb \
imx6dl-tx6u-811x.dtb \ imx6dl-tx6u-811x.dtb \
imx6dl-udoo.dtb \ imx6dl-udoo.dtb \
imx6dl-wandboard.dtb \ imx6dl-wandboard.dtb \
...@@ -360,6 +363,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ ...@@ -360,6 +363,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-tx6q-1010-comtft.dtb \ imx6q-tx6q-1010-comtft.dtb \
imx6q-tx6q-1020.dtb \ imx6q-tx6q-1020.dtb \
imx6q-tx6q-1020-comtft.dtb \ imx6q-tx6q-1020-comtft.dtb \
imx6q-tx6q-1036.dtb \
imx6q-tx6q-1110.dtb \ imx6q-tx6q-1110.dtb \
imx6q-udoo.dtb \ imx6q-udoo.dtb \
imx6q-wandboard.dtb \ imx6q-wandboard.dtb \
......
/*
* Copyright 2015-2016 Lothar Waßmann <LW@KARO-electronics.de>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* version 2 as published by the Free Software Foundation.
*
* This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include "imx6dl.dtsi"
#include "imx6qdl-tx6.dtsi"
/ {
model = "Ka-Ro electronics TX6S-8034 Module";
compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
aliases {
display = &display;
ipu1 = &ipu1;
};
cpus {
/delete-node/ cpu@1;
};
backlight: backlight {
compatible = "pwm-backlight";
pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_lcd0_pwr>;
enable-gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>;
power-supply = <&reg_lcd1_pwr>;
/*
* a poor man's way to create a 1:1 relationship between
* the PWM value and the actual duty cycle
*/
brightness-levels = < 0 1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18 19
20 21 22 23 24 25 26 27 28 29
30 31 32 33 34 35 36 37 38 39
40 41 42 43 44 45 46 47 48 49
50 51 52 53 54 55 56 57 58 59
60 61 62 63 64 65 66 67 68 69
70 71 72 73 74 75 76 77 78 79
80 81 82 83 84 85 86 87 88 89
90 91 92 93 94 95 96 97 98 99
100>;
default-brightness-level = <50>;
};
display: display@di0 {
compatible = "fsl,imx-parallel-display";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_disp0_2>;
interface-pix-fmt = "rgb24";
status = "okay";
port {
display0_in: endpoint {
remote-endpoint = <&ipu1_di0_disp0>;
};
};
display-timings {
native-mode = <&vga>;
vga: VGA {
clock-frequency = <25200000>;
hactive = <640>;
vactive = <480>;
hback-porch = <48>;
hsync-len = <96>;
hfront-porch = <16>;
vback-porch = <31>;
vsync-len = <2>;
vfront-porch = <12>;
hsync-active = <0>;
vsync-active = <0>;
de-active = <1>;
pixelclk-active = <0>;
};
ETV570 {
clock-frequency = <25200000>;
hactive = <640>;
vactive = <480>;
hback-porch = <114>;
hsync-len = <30>;
hfront-porch = <16>;
vback-porch = <32>;
vsync-len = <3>;
vfront-porch = <10>;
hsync-active = <0>;
vsync-active = <0>;
de-active = <1>;
pixelclk-active = <0>;
};
ET0350 {
clock-frequency = <6413760>;
hactive = <320>;
vactive = <240>;
hback-porch = <34>;
hsync-len = <34>;
hfront-porch = <20>;
vback-porch = <15>;
vsync-len = <3>;
vfront-porch = <4>;
hsync-active = <0>;
vsync-active = <0>;
de-active = <1>;
pixelclk-active = <0>;
};
ET0430 {
clock-frequency = <9009000>;
hactive = <480>;
vactive = <272>;
hback-porch = <2>;
hsync-len = <41>;
hfront-porch = <2>;
vback-porch = <2>;
vsync-len = <10>;
vfront-porch = <2>;
hsync-active = <0>;
vsync-active = <0>;
de-active = <1>;
pixelclk-active = <1>;
};
ET0500 {
clock-frequency = <33264000>;
hactive = <800>;
vactive = <480>;
hback-porch = <88>;
hsync-len = <128>;
hfront-porch = <40>;
vback-porch = <33>;
vsync-len = <2>;
vfront-porch = <10>;
hsync-active = <0>;
vsync-active = <0>;
de-active = <1>;
pixelclk-active = <0>;
};
ET0700 { /* same as ET0500 */
clock-frequency = <33264000>;
hactive = <800>;
vactive = <480>;
hback-porch = <88>;
hsync-len = <128>;
hfront-porch = <40>;
vback-porch = <33>;
vsync-len = <2>;
vfront-porch = <10>;
hsync-active = <0>;
vsync-active = <0>;
de-active = <1>;
pixelclk-active = <0>;
};
ETQ570 {
clock-frequency = <6596040>;
hactive = <320>;
vactive = <240>;
hback-porch = <38>;
hsync-len = <30>;
hfront-porch = <30>;
vback-porch = <16>;
vsync-len = <3>;
vfront-porch = <4>;
hsync-active = <0>;
vsync-active = <0>;
de-active = <1>;
pixelclk-active = <0>;
};
};
};
};
&ds1339 {
status = "disabled";
};
&pinctrl_usdhc1 {
fsl,pins = <
MX6QDL_PAD_SD1_CMD__SD1_CMD 0x070b1
MX6QDL_PAD_SD1_CLK__SD1_CLK 0x070b1
MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x070b1
MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x070b1
MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x070b1
MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x070b1
MX6QDL_PAD_SD3_CMD__GPIO7_IO02 0x170b0 /* SD1 CD */
>;
};
&ipu1_di0_disp0 {
remote-endpoint = <&display0_in>;
};
&reg_lcd0_pwr {
status = "disabled";
};
/*
* Copyright 2015-2016 Lothar Waßmann <LW@KARO-electronics.de>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* version 2 as published by the Free Software Foundation.
*
* This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include "imx6dl.dtsi"
#include "imx6qdl-tx6.dtsi"
/ {
model = "Ka-Ro electronics TX6S-8035 Module";
compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
aliases {
display = &display;
ipu1 = &ipu1;
};
cpus {
/delete-node/ cpu@1;
};
backlight: backlight {
compatible = "pwm-backlight";
pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_lcd0_pwr>;
enable-gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>;
power-supply = <&reg_lcd1_pwr>;
/*
* a poor man's way to create a 1:1 relationship between
* the PWM value and the actual duty cycle
*/
brightness-levels = < 0 1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18 19
20 21 22 23 24 25 26 27 28 29
30 31 32 33 34 35 36 37 38 39
40 41 42 43 44 45 46 47 48 49
50 51 52 53 54 55 56 57 58 59
60 61 62 63 64 65 66 67 68 69
70 71 72 73 74 75 76 77 78 79
80 81 82 83 84 85 86 87 88 89
90 91 92 93 94 95 96 97 98 99
100>;
default-brightness-level = <50>;
};
display: display@di0 {
compatible = "fsl,imx-parallel-display";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_disp0_2>;
interface-pix-fmt = "rgb24";
status = "okay";
port {
display0_in: endpoint {
remote-endpoint = <&ipu1_di0_disp0>;
};
};
display-timings {
native-mode = <&vga>;
vga: VGA {
clock-frequency = <25200000>;
hactive = <640>;
vactive = <480>;
hback-porch = <48>;
hsync-len = <96>;
hfront-porch = <16>;
vback-porch = <31>;
vsync-len = <2>;
vfront-porch = <12>;
hsync-active = <0>;
vsync-active = <0>;
de-active = <1>;
pixelclk-active = <0>;
};
ETV570 {
clock-frequency = <25200000>;
hactive = <640>;
vactive = <480>;
hback-porch = <114>;
hsync-len = <30>;
hfront-porch = <16>;
vback-porch = <32>;
vsync-len = <3>;
vfront-porch = <10>;
hsync-active = <0>;
vsync-active = <0>;
de-active = <1>;
pixelclk-active = <0>;
};
ET0350 {
clock-frequency = <6413760>;
hactive = <320>;
vactive = <240>;
hback-porch = <34>;
hsync-len = <34>;
hfront-porch = <20>;
vback-porch = <15>;
vsync-len = <3>;
vfront-porch = <4>;
hsync-active = <0>;
vsync-active = <0>;
de-active = <1>;
pixelclk-active = <0>;
};
ET0430 {
clock-frequency = <9009000>;
hactive = <480>;
vactive = <272>;
hback-porch = <2>;
hsync-len = <41>;
hfront-porch = <2>;
vback-porch = <2>;
vsync-len = <10>;
vfront-porch = <2>;
hsync-active = <0>;
vsync-active = <0>;
de-active = <1>;
pixelclk-active = <1>;
};
ET0500 {
clock-frequency = <33264000>;
hactive = <800>;
vactive = <480>;
hback-porch = <88>;
hsync-len = <128>;
hfront-porch = <40>;
vback-porch = <33>;
vsync-len = <2>;
vfront-porch = <10>;
hsync-active = <0>;
vsync-active = <0>;
de-active = <1>;
pixelclk-active = <0>;
};
ET0700 { /* same as ET0500 */
clock-frequency = <33264000>;
hactive = <800>;
vactive = <480>;
hback-porch = <88>;
hsync-len = <128>;
hfront-porch = <40>;
vback-porch = <33>;
vsync-len = <2>;
vfront-porch = <10>;
hsync-active = <0>;
vsync-active = <0>;
de-active = <1>;
pixelclk-active = <0>;
};
ETQ570 {
clock-frequency = <6596040>;
hactive = <320>;
vactive = <240>;
hback-porch = <38>;
hsync-len = <30>;
hfront-porch = <30>;
vback-porch = <16>;
vsync-len = <3>;
vfront-porch = <4>;
hsync-active = <0>;
vsync-active = <0>;
de-active = <1>;
pixelclk-active = <0>;
};
};
};
};
&ds1339 {
status = "disabled";
};
&gpmi {
status = "disabled";
};
&ipu1_di0_disp0 {
remote-endpoint = <&display0_in>;
};
&reg_lcd0_pwr {
status = "disabled";
};
&usdhc4 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc4>;
bus-width = <4>;
non-removable;
no-1-8-v;
fsl,wp-controller;
status = "okay";
};
&iomuxc {
pinctrl_usdhc4: usdhc4grp {
fsl,pins = <
MX6QDL_PAD_SD4_CMD__SD4_CMD 0x070b1
MX6QDL_PAD_SD4_CLK__SD4_CLK 0x070b1
MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x070b1
MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x070b1
MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x070b1
MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x070b1
MX6QDL_PAD_NANDF_ALE__SD4_RESET 0x0b0b1
>;
};
};
/*
* Copyright 2014-2016 Lothar Waßmann <LW@KARO-electronics.de>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* version 2 as published by the Free Software Foundation.
*
* This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include "imx6dl.dtsi"
#include "imx6qdl-tx6.dtsi"
/ {
model = "Ka-Ro electronics TX6U-8033 Module";
compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
aliases {
display = &display;
};
backlight: backlight {
compatible = "pwm-backlight";
pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_lcd0_pwr>;
enable-gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>;
power-supply = <&reg_lcd1_pwr>;
/*
* a poor man's way to create a 1:1 relationship between
* the PWM value and the actual duty cycle
*/
brightness-levels = < 0 1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18 19
20 21 22 23 24 25 26 27 28 29
30 31 32 33 34 35 36 37 38 39
40 41 42 43 44 45 46 47 48 49
50 51 52 53 54 55 56 57 58 59
60 61 62 63 64 65 66 67 68 69
70 71 72 73 74 75 76 77 78 79
80 81 82 83 84 85 86 87 88 89
90 91 92 93 94 95 96 97 98 99
100>;
default-brightness-level = <50>;
};
display: display@di0 {
compatible = "fsl,imx-parallel-display";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_disp0_2>;
interface-pix-fmt = "rgb24";
status = "okay";
port {
display0_in: endpoint {
remote-endpoint = <&ipu1_di0_disp0>;
};
};
display-timings {
native-mode = <&vga>;
vga: VGA {
clock-frequency = <25200000>;
hactive = <640>;
vactive = <480>;
hback-porch = <48>;
hsync-len = <96>;
hfront-porch = <16>;
vback-porch = <31>;
vsync-len = <2>;
vfront-porch = <12>;
hsync-active = <0>;
vsync-active = <0>;
de-active = <1>;
pixelclk-active = <0>;
};
ETV570 {
clock-frequency = <25200000>;
hactive = <640>;
vactive = <480>;
hback-porch = <114>;
hsync-len = <30>;
hfront-porch = <16>;
vback-porch = <32>;
vsync-len = <3>;
vfront-porch = <10>;
hsync-active = <0>;
vsync-active = <0>;
de-active = <1>;
pixelclk-active = <0>;
};
ET0350 {
clock-frequency = <6413760>;
hactive = <320>;
vactive = <240>;
hback-porch = <34>;
hsync-len = <34>;
hfront-porch = <20>;
vback-porch = <15>;
vsync-len = <3>;
vfront-porch = <4>;
hsync-active = <0>;
vsync-active = <0>;
de-active = <1>;
pixelclk-active = <0>;
};
ET0430 {
clock-frequency = <9009000>;
hactive = <480>;
vactive = <272>;
hback-porch = <2>;
hsync-len = <41>;
hfront-porch = <2>;
vback-porch = <2>;
vsync-len = <10>;
vfront-porch = <2>;
hsync-active = <0>;
vsync-active = <0>;
de-active = <1>;
pixelclk-active = <1>;
};
ET0500 {
clock-frequency = <33264000>;
hactive = <800>;
vactive = <480>;
hback-porch = <88>;
hsync-len = <128>;
hfront-porch = <40>;
vback-porch = <33>;
vsync-len = <2>;
vfront-porch = <10>;
hsync-active = <0>;
vsync-active = <0>;
de-active = <1>;
pixelclk-active = <0>;
};
ET0700 { /* same as ET0500 */
clock-frequency = <33264000>;
hactive = <800>;
vactive = <480>;
hback-porch = <88>;
hsync-len = <128>;
hfront-porch = <40>;
vback-porch = <33>;
vsync-len = <2>;
vfront-porch = <10>;
hsync-active = <0>;
vsync-active = <0>;
de-active = <1>;
pixelclk-active = <0>;
};
ETQ570 {
clock-frequency = <6596040>;
hactive = <320>;
vactive = <240>;
hback-porch = <38>;
hsync-len = <30>;
hfront-porch = <30>;
vback-porch = <16>;
vsync-len = <3>;
vfront-porch = <4>;
hsync-active = <0>;
vsync-active = <0>;
de-active = <1>;
pixelclk-active = <0>;
};
};
};
};
&ds1339 {
status = "disabled";
};
&gpmi {
status = "disabled";
};
&ipu1_di0_disp0 {
remote-endpoint = <&display0_in>;
};
&reg_lcd0_pwr {
status = "disabled";
};
&usdhc4 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc4>;
bus-width = <4>;
non-removable;
no-1-8-v;
fsl,wp-controller;
status = "okay";
};
&iomuxc {
pinctrl_usdhc4: usdhc4grp {
fsl,pins = <
MX6QDL_PAD_SD4_CMD__SD4_CMD 0x070b1
MX6QDL_PAD_SD4_CLK__SD4_CLK 0x070b1
MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x070b1
MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x070b1
MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x070b1
MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x070b1
MX6QDL_PAD_NANDF_ALE__SD4_RESET 0x0b0b1
>;
};
};
/*
* Copyright 2014-2016 Lothar Waßmann <LW@KARO-electronics.de>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* version 2 as published by the Free Software Foundation.
*
* This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include "imx6q.dtsi"
#include "imx6qdl-tx6.dtsi"
/ {
model = "Ka-Ro electronics TX6Q-1036 Module";
compatible = "karo,imx6q-tx6q", "fsl,imx6q";
aliases {
display = &display;
};
backlight: backlight {
compatible = "pwm-backlight";
pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_lcd0_pwr>;
enable-gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>;
power-supply = <&reg_lcd1_pwr>;
/*
* a poor man's way to create a 1:1 relationship between
* the PWM value and the actual duty cycle
*/
brightness-levels = < 0 1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18 19
20 21 22 23 24 25 26 27 28 29
30 31 32 33 34 35 36 37 38 39
40 41 42 43 44 45 46 47 48 49
50 51 52 53 54 55 56 57 58 59
60 61 62 63 64 65 66 67 68 69
70 71 72 73 74 75 76 77 78 79
80 81 82 83 84 85 86 87 88 89
90 91 92 93 94 95 96 97 98 99
100>;
default-brightness-level = <50>;
};
display: display@di0 {
compatible = "fsl,imx-parallel-display";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_disp0_2>;
interface-pix-fmt = "rgb24";
status = "okay";
port {
display0_in: endpoint {
remote-endpoint = <&ipu1_di0_disp0>;
};
};
display-timings {
native-mode = <&vga>;
vga: VGA {
clock-frequency = <25200000>;
hactive = <640>;
vactive = <480>;
hback-porch = <48>;
hsync-len = <96>;
hfront-porch = <16>;
vback-porch = <31>;
vsync-len = <2>;
vfront-porch = <12>;
hsync-active = <0>;
vsync-active = <0>;
de-active = <1>;
pixelclk-active = <0>;
};
ETV570 {
clock-frequency = <25200000>;
hactive = <640>;
vactive = <480>;
hback-porch = <114>;
hsync-len = <30>;
hfront-porch = <16>;
vback-porch = <32>;
vsync-len = <3>;
vfront-porch = <10>;
hsync-active = <0>;
vsync-active = <0>;
de-active = <1>;
pixelclk-active = <0>;
};
ET0350 {
clock-frequency = <6413760>;
hactive = <320>;
vactive = <240>;
hback-porch = <34>;
hsync-len = <34>;
hfront-porch = <20>;
vback-porch = <15>;
vsync-len = <3>;
vfront-porch = <4>;
hsync-active = <0>;
vsync-active = <0>;
de-active = <1>;
pixelclk-active = <0>;
};
ET0430 {
clock-frequency = <9009000>;
hactive = <480>;
vactive = <272>;
hback-porch = <2>;
hsync-len = <41>;
hfront-porch = <2>;
vback-porch = <2>;
vsync-len = <10>;
vfront-porch = <2>;
hsync-active = <0>;
vsync-active = <0>;
de-active = <1>;
pixelclk-active = <1>;
};
ET0500 {
clock-frequency = <33264000>;
hactive = <800>;
vactive = <480>;
hback-porch = <88>;
hsync-len = <128>;
hfront-porch = <40>;
vback-porch = <33>;
vsync-len = <2>;
vfront-porch = <10>;
hsync-active = <0>;
vsync-active = <0>;
de-active = <1>;
pixelclk-active = <0>;
};
ET0700 { /* same as ET0500 */
clock-frequency = <33264000>;
hactive = <800>;
vactive = <480>;
hback-porch = <88>;
hsync-len = <128>;
hfront-porch = <40>;
vback-porch = <33>;
vsync-len = <2>;
vfront-porch = <10>;
hsync-active = <0>;
vsync-active = <0>;
de-active = <1>;
pixelclk-active = <0>;
};
ETQ570 {
clock-frequency = <6596040>;
hactive = <320>;
vactive = <240>;
hback-porch = <38>;
hsync-len = <30>;
hfront-porch = <30>;
vback-porch = <16>;
vsync-len = <3>;
vfront-porch = <4>;
hsync-active = <0>;
vsync-active = <0>;
de-active = <1>;
pixelclk-active = <0>;
};
};
};
};
&ds1339 {
status = "disabled";
};
&gpmi {
status = "disabled";
};
&ipu1_di0_disp0 {
remote-endpoint = <&display0_in>;
};
&ipu2 {
status = "disabled";
};
&reg_lcd0_pwr {
status = "disabled";
};
&usdhc4 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc4>;
bus-width = <4>;
non-removable;
no-1-8-v;
fsl,wp-controller;
status = "okay";
};
&iomuxc {
pinctrl_usdhc4: usdhc4grp {
fsl,pins = <
MX6QDL_PAD_SD4_CMD__SD4_CMD 0x070b1
MX6QDL_PAD_SD4_CLK__SD4_CLK 0x070b1
MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x070b1
MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x070b1
MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x070b1
MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x070b1
MX6QDL_PAD_NANDF_ALE__SD4_RESET 0x0b0b1
>;
};
};
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment