Commit 1a096afc authored by Vladimir Zapolskiy's avatar Vladimir Zapolskiy

ARM: dts: lpc32xx: ea3250: avoid extension of device nodes by absolute path

The change simplifies layout of EA3250 board description by
referencing device nodes of LPC32xx controllers by label.

No functional change intended.
Acked-by: default avatarSylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: default avatarVladimir Zapolskiy <vz@mleia.com>
parent 9b8ad3fb
......@@ -25,119 +25,6 @@ memory {
reg = <0x80000000 0x4000000>;
};
ahb {
mac: ethernet@31060000 {
phy-mode = "rmii";
use-iram;
};
/* 128MB Flash via SLC NAND controller */
slc: flash@20020000 {
status = "okay";
#address-cells = <1>;
#size-cells = <1>;
nxp,wdr-clks = <14>;
nxp,wwidth = <260000000>;
nxp,whold = <104000000>;
nxp,wsetup = <200000000>;
nxp,rdr-clks = <14>;
nxp,rwidth = <34666666>;
nxp,rhold = <104000000>;
nxp,rsetup = <200000000>;
nand-on-flash-bbt;
gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */
mtd0@00000000 {
label = "ea3250-boot";
reg = <0x00000000 0x00080000>;
read-only;
};
mtd1@00080000 {
label = "ea3250-uboot";
reg = <0x00080000 0x000c0000>;
read-only;
};
mtd2@00140000 {
label = "ea3250-kernel";
reg = <0x00140000 0x00400000>;
};
mtd3@00540000 {
label = "ea3250-rootfs";
reg = <0x00540000 0x07ac0000>;
};
};
apb {
uart5: serial@40090000 {
status = "okay";
};
uart3: serial@40080000 {
status = "okay";
};
uart6: serial@40098000 {
status = "okay";
};
i2c1: i2c@400A0000 {
clock-frequency = <100000>;
eeprom@50 {
compatible = "at,24c256";
reg = <0x50>;
};
eeprom@57 {
compatible = "at,24c64";
reg = <0x57>;
};
uda1380: uda1380@18 {
compatible = "nxp,uda1380";
reg = <0x18>;
power-gpio = <&gpio 0x59 0>;
reset-gpio = <&gpio 0x51 0>;
dac-clk = "wspll";
};
pca9532: pca9532@60 {
compatible = "nxp,pca9532";
gpio-controller;
#gpio-cells = <2>;
reg = <0x60>;
};
};
i2c2: i2c@400A8000 {
clock-frequency = <100000>;
};
sd@20098000 {
wp-gpios = <&pca9532 5 0>;
cd-gpios = <&pca9532 4 0>;
cd-inverted;
bus-width = <4>;
status = "okay";
};
};
fab {
uart1: serial@40014000 {
status = "okay";
};
/* 3-axis accelerometer X,Y,Z (or AD-IN instead of Z) */
adc@40048000 {
status = "okay";
};
};
};
gpio_keys {
compatible = "gpio-keys";
#address-cells = <1>;
......@@ -258,12 +145,44 @@ lede8 {
};
};
/* Here, choose exactly one from: ohci, usbd */
&ohci /* &usbd */ {
transceiver = <&isp1301>;
/* 3-axis accelerometer X,Y,Z (or AD-IN instead of Z) */
&adc {
status = "okay";
};
&i2c1 {
clock-frequency = <100000>;
uda1380: uda1380@18 {
compatible = "nxp,uda1380";
reg = <0x18>;
power-gpio = <&gpio 0x59 0>;
reset-gpio = <&gpio 0x51 0>;
dac-clk = "wspll";
};
eeprom@50 {
compatible = "at,24c256";
reg = <0x50>;
};
eeprom@57 {
compatible = "at,24c64";
reg = <0x57>;
};
pca9532: pca9532@60 {
compatible = "nxp,pca9532";
gpio-controller;
#gpio-cells = <2>;
reg = <0x60>;
};
};
&i2c2 {
clock-frequency = <100000>;
};
&i2cusb {
clock-frequency = <100000>;
......@@ -272,3 +191,78 @@ isp1301: usb-transceiver@2d {
reg = <0x2d>;
};
};
&mac {
phy-mode = "rmii";
use-iram;
};
/* Here, choose exactly one from: ohci, usbd */
&ohci /* &usbd */ {
transceiver = <&isp1301>;
status = "okay";
};
&sd {
wp-gpios = <&pca9532 5 0>;
cd-gpios = <&pca9532 4 0>;
cd-inverted;
bus-width = <4>;
status = "okay";
};
/* 128MB Flash via SLC NAND controller */
&slc {
#address-cells = <1>;
#size-cells = <1>;
status = "okay";
nxp,wdr-clks = <14>;
nxp,wwidth = <260000000>;
nxp,whold = <104000000>;
nxp,wsetup = <200000000>;
nxp,rdr-clks = <14>;
nxp,rwidth = <34666666>;
nxp,rhold = <104000000>;
nxp,rsetup = <200000000>;
nand-on-flash-bbt;
gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */
mtd0@00000000 {
label = "ea3250-boot";
reg = <0x00000000 0x00080000>;
read-only;
};
mtd1@00080000 {
label = "ea3250-uboot";
reg = <0x00080000 0x000c0000>;
read-only;
};
mtd2@00140000 {
label = "ea3250-kernel";
reg = <0x00140000 0x00400000>;
};
mtd3@00540000 {
label = "ea3250-rootfs";
reg = <0x00540000 0x07ac0000>;
};
};
&uart1 {
status = "okay";
};
&uart3 {
status = "okay";
};
&uart5 {
status = "okay";
};
&uart6 {
status = "okay";
};
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment