Skip to content

L
linux
Commit 1bdb7b76 authored by Jiaxun Yang's avatar Jiaxun Yang Committed by Paul Burton
Browse files
Options

MIPS: Loongson64: Cleanup unused code 

Clean up legacy code after stripping out Loongson2ef code.
Signed-off-by: default avatarJiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: default avatarPaul Burton <paulburton@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: paul.burton@mips.com
parent 5831fdb0
Hide whitespace changes
Inline Side-by-side
Showing with 34 additions and 1543 deletions
arch/mips/include/asm/bootinfo.h
View file @ 1bdb7b76
......@@ -61,7 +61,7 @@
/*
* Valid machtype for Loongson family
*/
enum loongson_machine_type {
enum loongson2ef_machine_type {
MACH_LOONGSON_UNKNOWN,
MACH_LEMOTE_FL2E,
MACH_LEMOTE_FL2F,
......@@ -70,7 +70,6 @@ enum loongson_machine_type {
MACH_DEXXON_GDIUM2F10,
MACH_LEMOTE_NAS,
MACH_LEMOTE_LL2F,
MACH_LOONGSON_GENERIC,
MACH_LOONGSON_END
};
......
arch/mips/include/asm/mach-loongson64/cpu-feature-overrides.h
View file @ 1bdb7b76
......@@ -44,10 +44,8 @@
#define cpu_has_vtag_icache 0
#define cpu_has_watch 1
#ifdef CONFIG_CPU_LOONGSON64
#define cpu_has_wsbh 1
#define cpu_has_ic_fills_f_dc 1
#define cpu_hwrena_impl_bits 0xc0000000
#endif
#endif /* __ASM_MACH_LOONGSON64_CPU_FEATURE_OVERRIDES_H */
arch/mips/include/asm/mach-loongson64/cs5536/cs5536.h deleted 100644 → 0
View file @ 5831fdb0
/* SPDX-License-Identifier: GPL-2.0 */
/*
* The header file of cs5536 south bridge.
*
* Copyright (C) 2007 Lemote, Inc.
* Author : jlliu <liujl@lemote.com>
*/
#ifndef _CS5536_H
#define _CS5536_H
#include <linux/types.h>
extern void _rdmsr(u32 msr, u32 *hi, u32 *lo);
extern void _wrmsr(u32 msr, u32 hi, u32 lo);
/*
* MSR module base
*/
#define CS5536_SB_MSR_BASE (0x00000000)
#define CS5536_GLIU_MSR_BASE (0x10000000)
#define CS5536_ILLEGAL_MSR_BASE (0x20000000)
#define CS5536_USB_MSR_BASE (0x40000000)
#define CS5536_IDE_MSR_BASE (0x60000000)
#define CS5536_DIVIL_MSR_BASE (0x80000000)
#define CS5536_ACC_MSR_BASE (0xa0000000)
#define CS5536_UNUSED_MSR_BASE (0xc0000000)
#define CS5536_GLCP_MSR_BASE (0xe0000000)
#define SB_MSR_REG(offset) (CS5536_SB_MSR_BASE | (offset))
#define GLIU_MSR_REG(offset) (CS5536_GLIU_MSR_BASE | (offset))
#define ILLEGAL_MSR_REG(offset) (CS5536_ILLEGAL_MSR_BASE | (offset))
#define USB_MSR_REG(offset) (CS5536_USB_MSR_BASE | (offset))
#define IDE_MSR_REG(offset) (CS5536_IDE_MSR_BASE | (offset))
#define DIVIL_MSR_REG(offset) (CS5536_DIVIL_MSR_BASE | (offset))
#define ACC_MSR_REG(offset) (CS5536_ACC_MSR_BASE | (offset))
#define UNUSED_MSR_REG(offset) (CS5536_UNUSED_MSR_BASE | (offset))
#define GLCP_MSR_REG(offset) (CS5536_GLCP_MSR_BASE | (offset))
/*
* BAR SPACE OF VIRTUAL PCI :
* range for pci probe use, length is the actual size.
*/
/* IO space for all DIVIL modules */
#define CS5536_IRQ_RANGE 0xffffffe0 /* USERD FOR PCI PROBE */
#define CS5536_IRQ_LENGTH 0x20 /* THE REGS ACTUAL LENGTH */
#define CS5536_SMB_RANGE 0xfffffff8
#define CS5536_SMB_LENGTH 0x08
#define CS5536_GPIO_RANGE 0xffffff00
#define CS5536_GPIO_LENGTH 0x100
#define CS5536_MFGPT_RANGE 0xffffffc0
#define CS5536_MFGPT_LENGTH 0x40
#define CS5536_ACPI_RANGE 0xffffffe0
#define CS5536_ACPI_LENGTH 0x20
#define CS5536_PMS_RANGE 0xffffff80
#define CS5536_PMS_LENGTH 0x80
/* IO space for IDE */
#define CS5536_IDE_RANGE 0xfffffff0
#define CS5536_IDE_LENGTH 0x10
/* IO space for ACC */
#define CS5536_ACC_RANGE 0xffffff80
#define CS5536_ACC_LENGTH 0x80
/* MEM space for ALL USB modules */
#define CS5536_OHCI_RANGE 0xfffff000
#define CS5536_OHCI_LENGTH 0x1000
#define CS5536_EHCI_RANGE 0xfffff000
#define CS5536_EHCI_LENGTH 0x1000
/*
* PCI MSR ACCESS
*/
#define PCI_MSR_CTRL 0xF0
#define PCI_MSR_ADDR 0xF4
#define PCI_MSR_DATA_LO 0xF8
#define PCI_MSR_DATA_HI 0xFC
/**************** MSR *****************************/
/*
* GLIU STANDARD MSR
*/
#define GLIU_CAP 0x00
#define GLIU_CONFIG 0x01
#define GLIU_SMI 0x02
#define GLIU_ERROR 0x03
#define GLIU_PM 0x04
#define GLIU_DIAG 0x05
/*
* GLIU SPEC. MSR
*/
#define GLIU_P2D_BM0 0x20
#define GLIU_P2D_BM1 0x21
#define GLIU_P2D_BM2 0x22
#define GLIU_P2D_BMK0 0x23
#define GLIU_P2D_BMK1 0x24
#define GLIU_P2D_BM3 0x25
#define GLIU_P2D_BM4 0x26
#define GLIU_COH 0x80
#define GLIU_PAE 0x81
#define GLIU_ARB 0x82
#define GLIU_ASMI 0x83
#define GLIU_AERR 0x84
#define GLIU_DEBUG 0x85
#define GLIU_PHY_CAP 0x86
#define GLIU_NOUT_RESP 0x87
#define GLIU_NOUT_WDATA 0x88
#define GLIU_WHOAMI 0x8B
#define GLIU_SLV_DIS 0x8C
#define GLIU_IOD_BM0 0xE0
#define GLIU_IOD_BM1 0xE1
#define GLIU_IOD_BM2 0xE2
#define GLIU_IOD_BM3 0xE3
#define GLIU_IOD_BM4 0xE4
#define GLIU_IOD_BM5 0xE5
#define GLIU_IOD_BM6 0xE6
#define GLIU_IOD_BM7 0xE7
#define GLIU_IOD_BM8 0xE8
#define GLIU_IOD_BM9 0xE9
#define GLIU_IOD_SC0 0xEA
#define GLIU_IOD_SC1 0xEB
#define GLIU_IOD_SC2 0xEC
#define GLIU_IOD_SC3 0xED
#define GLIU_IOD_SC4 0xEE
#define GLIU_IOD_SC5 0xEF
#define GLIU_IOD_SC6 0xF0
#define GLIU_IOD_SC7 0xF1
/*
* SB STANDARD
*/
#define SB_CAP 0x00
#define SB_CONFIG 0x01
#define SB_SMI 0x02
#define SB_ERROR 0x03
#define SB_MAR_ERR_EN 0x00000001
#define SB_TAR_ERR_EN 0x00000002
#define SB_RSVD_BIT1 0x00000004
#define SB_EXCEP_ERR_EN 0x00000008
#define SB_SYSE_ERR_EN 0x00000010
#define SB_PARE_ERR_EN 0x00000020
#define SB_TAS_ERR_EN 0x00000040
#define SB_MAR_ERR_FLAG 0x00010000
#define SB_TAR_ERR_FLAG 0x00020000
#define SB_RSVD_BIT2 0x00040000
#define SB_EXCEP_ERR_FLAG 0x00080000
#define SB_SYSE_ERR_FLAG 0x00100000
#define SB_PARE_ERR_FLAG 0x00200000
#define SB_TAS_ERR_FLAG 0x00400000
#define SB_PM 0x04
#define SB_DIAG 0x05
/*
* SB SPEC.
*/
#define SB_CTRL 0x10
#define SB_R0 0x20
#define SB_R1 0x21
#define SB_R2 0x22
#define SB_R3 0x23
#define SB_R4 0x24
#define SB_R5 0x25
#define SB_R6 0x26
#define SB_R7 0x27
#define SB_R8 0x28
#define SB_R9 0x29
#define SB_R10 0x2A
#define SB_R11 0x2B
#define SB_R12 0x2C
#define SB_R13 0x2D
#define SB_R14 0x2E
#define SB_R15 0x2F
/*
* GLCP STANDARD
*/
#define GLCP_CAP 0x00
#define GLCP_CONFIG 0x01
#define GLCP_SMI 0x02
#define GLCP_ERROR 0x03
#define GLCP_PM 0x04
#define GLCP_DIAG 0x05
/*
* GLCP SPEC.
*/
#define GLCP_CLK_DIS_DELAY 0x08
#define GLCP_PM_CLK_DISABLE 0x09
#define GLCP_GLB_PM 0x0B
#define GLCP_DBG_OUT 0x0C
#define GLCP_RSVD1 0x0D
#define GLCP_SOFT_COM 0x0E
#define SOFT_BAR_SMB_FLAG 0x00000001
#define SOFT_BAR_GPIO_FLAG 0x00000002
#define SOFT_BAR_MFGPT_FLAG 0x00000004
#define SOFT_BAR_IRQ_FLAG 0x00000008
#define SOFT_BAR_PMS_FLAG 0x00000010
#define SOFT_BAR_ACPI_FLAG 0x00000020
#define SOFT_BAR_IDE_FLAG 0x00000400
#define SOFT_BAR_ACC_FLAG 0x00000800
#define SOFT_BAR_OHCI_FLAG 0x00001000
#define SOFT_BAR_EHCI_FLAG 0x00002000
#define GLCP_RSVD2 0x0F
#define GLCP_CLK_OFF 0x10
#define GLCP_CLK_ACTIVE 0x11
#define GLCP_CLK_DISABLE 0x12
#define GLCP_CLK4ACK 0x13
#define GLCP_SYS_RST 0x14
#define GLCP_RSVD3 0x15
#define GLCP_DBG_CLK_CTRL 0x16
#define GLCP_CHIP_REV_ID 0x17
/* PIC */
#define PIC_YSEL_LOW 0x20
#define PIC_YSEL_LOW_USB_SHIFT 8
#define PIC_YSEL_LOW_ACC_SHIFT 16
#define PIC_YSEL_LOW_FLASH_SHIFT 24
#define PIC_YSEL_HIGH 0x21
#define PIC_ZSEL_LOW 0x22
#define PIC_ZSEL_HIGH 0x23
#define PIC_IRQM_PRIM 0x24
#define PIC_IRQM_LPC 0x25
#define PIC_XIRR_STS_LOW 0x26
#define PIC_XIRR_STS_HIGH 0x27
#define PCI_SHDW 0x34
/*
* DIVIL STANDARD
*/
#define DIVIL_CAP 0x00
#define DIVIL_CONFIG 0x01
#define DIVIL_SMI 0x02
#define DIVIL_ERROR 0x03
#define DIVIL_PM 0x04
#define DIVIL_DIAG 0x05
/*
* DIVIL SPEC.
*/
#define DIVIL_LBAR_IRQ 0x08
#define DIVIL_LBAR_KEL 0x09
#define DIVIL_LBAR_SMB 0x0B
#define DIVIL_LBAR_GPIO 0x0C
#define DIVIL_LBAR_MFGPT 0x0D
#define DIVIL_LBAR_ACPI 0x0E
#define DIVIL_LBAR_PMS 0x0F
#define DIVIL_LEG_IO 0x14
#define DIVIL_BALL_OPTS 0x15
#define DIVIL_SOFT_IRQ 0x16
#define DIVIL_SOFT_RESET 0x17
/* MFGPT */
#define MFGPT_IRQ 0x28
/*
* IDE STANDARD
*/
#define IDE_CAP 0x00
#define IDE_CONFIG 0x01
#define IDE_SMI 0x02
#define IDE_ERROR 0x03
#define IDE_PM 0x04
#define IDE_DIAG 0x05
/*
* IDE SPEC.
*/
#define IDE_IO_BAR 0x08
#define IDE_CFG 0x10
#define IDE_DTC 0x12
#define IDE_CAST 0x13
#define IDE_ETC 0x14
#define IDE_INTERNAL_PM 0x15
/*
* ACC STANDARD
*/
#define ACC_CAP 0x00
#define ACC_CONFIG 0x01
#define ACC_SMI 0x02
#define ACC_ERROR 0x03
#define ACC_PM 0x04
#define ACC_DIAG 0x05
/*
* USB STANDARD
*/
#define USB_CAP 0x00
#define USB_CONFIG 0x01
#define USB_SMI 0x02
#define USB_ERROR 0x03
#define USB_PM 0x04
#define USB_DIAG 0x05
/*
* USB SPEC.
*/
#define USB_OHCI 0x08
#define USB_EHCI 0x09
/****************** NATIVE ***************************/
/* GPIO : I/O SPACE; REG : 32BITS */
#define GPIOL_OUT_VAL 0x00
#define GPIOL_OUT_EN 0x04
#endif /* _CS5536_H */
arch/mips/include/asm/mach-loongson64/cs5536/cs5536_mfgpt.h deleted 100644 → 0
View file @ 5831fdb0
/* SPDX-License-Identifier: GPL-2.0 */
/*
* cs5536 mfgpt header file
*/
#ifndef _CS5536_MFGPT_H
#define _CS5536_MFGPT_H
#include <cs5536/cs5536.h>
#include <cs5536/cs5536_pci.h>
#ifdef CONFIG_CS5536_MFGPT
extern void setup_mfgpt0_timer(void);
extern void disable_mfgpt0_counter(void);
extern void enable_mfgpt0_counter(void);
#else
static inline void __maybe_unused setup_mfgpt0_timer(void)
{
}
static inline void __maybe_unused disable_mfgpt0_counter(void)
{
}
static inline void __maybe_unused enable_mfgpt0_counter(void)
{
}
#endif
#define MFGPT_TICK_RATE 14318000
#define COMPARE ((MFGPT_TICK_RATE + HZ/2) / HZ)
#define MFGPT_BASE mfgpt_base
#define MFGPT0_CMP2 (MFGPT_BASE + 2)
#define MFGPT0_CNT (MFGPT_BASE + 4)
#define MFGPT0_SETUP (MFGPT_BASE + 6)
#endif /*!_CS5536_MFGPT_H */
arch/mips/include/asm/mach-loongson64/cs5536/cs5536_pci.h deleted 100644 → 0
View file @ 5831fdb0
/* SPDX-License-Identifier: GPL-2.0 */
/*
* the definition file of cs5536 Virtual Support Module(VSM).
* pci configuration space can be accessed through the VSM, so
* there is no need of the MSR read/write now, except the spec.
* MSR registers which are not implemented yet.
*
* Copyright (C) 2007 Lemote Inc.
* Author : jlliu, liujl@lemote.com
*/
#ifndef _CS5536_PCI_H
#define _CS5536_PCI_H
#include <linux/types.h>
#include <linux/pci_regs.h>
extern void cs5536_pci_conf_write4(int function, int reg, u32 value);
extern u32 cs5536_pci_conf_read4(int function, int reg);
#define CS5536_ACC_INTR 9
#define CS5536_IDE_INTR 14
#define CS5536_USB_INTR 11
#define CS5536_MFGPT_INTR 5
#define CS5536_UART1_INTR 4
#define CS5536_UART2_INTR 3
/************** PCI BUS DEVICE FUNCTION ***************/
/*
* PCI bus device function
*/
#define PCI_BUS_CS5536 0
#define PCI_IDSEL_CS5536 14
/********** STANDARD PCI-2.2 EXPANSION ****************/
/*
* PCI configuration space
* we have to virtualize the PCI configure space head, so we should
* define the necessary IDs and some others.
*/
/* CONFIG of PCI VENDOR ID*/
#define CFG_PCI_VENDOR_ID(mod_dev_id, sys_vendor_id) \
(((mod_dev_id) << 16) | (sys_vendor_id))
/* VENDOR ID */
#define CS5536_VENDOR_ID 0x1022
/* DEVICE ID */
#define CS5536_ISA_DEVICE_ID 0x2090
#define CS5536_IDE_DEVICE_ID 0x209a
#define CS5536_ACC_DEVICE_ID 0x2093
#define CS5536_OHCI_DEVICE_ID 0x2094
#define CS5536_EHCI_DEVICE_ID 0x2095
/* CLASS CODE : CLASS SUB-CLASS INTERFACE */
#define CS5536_ISA_CLASS_CODE 0x060100
#define CS5536_IDE_CLASS_CODE 0x010180
#define CS5536_ACC_CLASS_CODE 0x040100
#define CS5536_OHCI_CLASS_CODE 0x0C0310
#define CS5536_EHCI_CLASS_CODE 0x0C0320
/* BHLC : BIST HEADER-TYPE LATENCY-TIMER CACHE-LINE-SIZE */
#define CFG_PCI_CACHE_LINE_SIZE(header_type, latency_timer) \
((PCI_NONE_BIST << 24) | ((header_type) << 16) \
| ((latency_timer) << 8) | PCI_NORMAL_CACHE_LINE_SIZE);
#define PCI_NONE_BIST 0x00 /* RO not implemented yet. */
#define PCI_BRIDGE_HEADER_TYPE 0x80 /* RO */
#define PCI_NORMAL_HEADER_TYPE 0x00
#define PCI_NORMAL_LATENCY_TIMER 0x00
#define PCI_NORMAL_CACHE_LINE_SIZE 0x08 /* RW */
/* BAR */
#define PCI_BAR0_REG 0x10
#define PCI_BAR1_REG 0x14
#define PCI_BAR2_REG 0x18
#define PCI_BAR3_REG 0x1c
#define PCI_BAR4_REG 0x20
#define PCI_BAR5_REG 0x24
#define PCI_BAR_RANGE_MASK 0xFFFFFFFF
/* CARDBUS CIS POINTER */
#define PCI_CARDBUS_CIS_POINTER 0x00000000
/* SUBSYSTEM VENDOR ID */
#define CS5536_SUB_VENDOR_ID CS5536_VENDOR_ID
/* SUBSYSTEM ID */
#define CS5536_ISA_SUB_ID CS5536_ISA_DEVICE_ID
#define CS5536_IDE_SUB_ID CS5536_IDE_DEVICE_ID
#define CS5536_ACC_SUB_ID CS5536_ACC_DEVICE_ID
#define CS5536_OHCI_SUB_ID CS5536_OHCI_DEVICE_ID
#define CS5536_EHCI_SUB_ID CS5536_EHCI_DEVICE_ID
/* EXPANSION ROM BAR */
#define PCI_EXPANSION_ROM_BAR 0x00000000
/* CAPABILITIES POINTER */
#define PCI_CAPLIST_POINTER 0x00000000
#define PCI_CAPLIST_USB_POINTER 0x40
/* INTERRUPT */
#define CFG_PCI_INTERRUPT_LINE(pin, mod_intr) \
((PCI_MAX_LATENCY << 24) | (PCI_MIN_GRANT << 16) | \
((pin) << 8) | (mod_intr))
#define PCI_MAX_LATENCY 0x40
#define PCI_MIN_GRANT 0x00
#define PCI_DEFAULT_PIN 0x01
/*********** EXPANSION PCI REG ************************/
/*
* ISA EXPANSION
*/
#define PCI_UART1_INT_REG 0x50
#define PCI_UART2_INT_REG 0x54
#define PCI_ISA_FIXUP_REG 0x58
/*
* IDE EXPANSION
*/
#define PCI_IDE_CFG_REG 0x40
#define CS5536_IDE_FLASH_SIGNATURE 0xDEADBEEF
#define PCI_IDE_DTC_REG 0x48
#define PCI_IDE_CAST_REG 0x4C
#define PCI_IDE_ETC_REG 0x50
#define PCI_IDE_PM_REG 0x54
#define PCI_IDE_INT_REG 0x60
/*
* ACC EXPANSION
*/
#define PCI_ACC_INT_REG 0x50
/*
* OHCI EXPANSION : INTTERUPT IS IMPLEMENTED BY THE OHCI
*/
#define PCI_OHCI_PM_REG 0x40
#define PCI_OHCI_INT_REG 0x50
/*
* EHCI EXPANSION
*/
#define PCI_EHCI_LEGSMIEN_REG 0x50
#define PCI_EHCI_LEGSMISTS_REG 0x54
#define PCI_EHCI_FLADJ_REG 0x60
#endif /* _CS5536_PCI_H_ */
arch/mips/include/asm/mach-loongson64/cs5536/cs5536_vsm.h deleted 100644 → 0
View file @ 5831fdb0
/* SPDX-License-Identifier: GPL-2.0 */
/*
* the read/write interfaces for Virtual Support Module(VSM)
*
* Copyright (C) 2009 Lemote, Inc.
* Author: Wu Zhangjin <wuzhangjin@gmail.com>
*/
#ifndef _CS5536_VSM_H
#define _CS5536_VSM_H
#include <linux/types.h>
typedef void (*cs5536_pci_vsm_write)(int reg, u32 value);
typedef u32 (*cs5536_pci_vsm_read)(int reg);
#define DECLARE_CS5536_MODULE(name) \
extern void pci_##name##_write_reg(int reg, u32 value); \
extern u32 pci_##name##_read_reg(int reg);
/* ide module */
DECLARE_CS5536_MODULE(ide)
/* acc module */
DECLARE_CS5536_MODULE(acc)
/* ohci module */
DECLARE_CS5536_MODULE(ohci)
/* isa module */
DECLARE_CS5536_MODULE(isa)
/* ehci module */
DECLARE_CS5536_MODULE(ehci)
#endif /* _CS5536_VSM_H */
arch/mips/include/asm/mach-loongson64/irq.h
View file @ 1bdb7b76
......@@ -4,8 +4,6 @@
#include <boot_param.h>
#ifdef CONFIG_CPU_LOONGSON64
/* cpu core interrupt numbers */
#define MIPS_CPU_IRQ_BASE 56
......@@ -35,8 +33,6 @@
#define LOONGSON_INT_COREx_INTy(x, y) (1<<(x) | 1<<(y+4)) /* route to int y of core x */
#endif
extern void fixup_irqs(void);
extern void loongson3_ipi_interrupt(struct pt_regs *regs);
......
arch/mips/include/asm/mach-loongson64/kernel-entry-init.h
View file @ 1bdb7b76
......@@ -17,7 +17,6 @@
* Override macros used in arch/mips/kernel/head.S.
*/
.macro kernel_entry_setup
#ifdef CONFIG_CPU_LOONGSON64
.set push
.set mips64
/* Set LPA on LOONGSON3 config3 */
......@@ -47,14 +46,12 @@
2:
_ehb
.set pop
#endif
.endm
/*
* Do SMP slave processor setup.
*/
.macro smp_slave_setup
#ifdef CONFIG_CPU_LOONGSON64
.set push
.set mips64
/* Set LPA on LOONGSON3 config3 */
......@@ -84,7 +81,6 @@
2:
_ehb
.set pop
#endif
.endm
#endif /* __ASM_MACH_LOONGSON64_KERNEL_ENTRY_H */
arch/mips/include/asm/mach-loongson64/loongson.h
View file @ 1bdb7b76
......@@ -12,8 +12,6 @@
#include <linux/irq.h>
#include <boot_param.h>
/* loongson internal northbridge initialization */
extern void bonito_irq_init(void);
/* machine-specific reboot/halt operation */
extern void mach_prepare_reboot(void);
......@@ -27,24 +25,9 @@ extern const struct plat_smp_ops loongson3_smp_ops;
/* loongson-specific command line, env and memory initialization */
extern void __init prom_init_memory(void);
extern void __init prom_init_cmdline(void);
extern void __init prom_init_machtype(void);
extern void __init prom_init_env(void);
#ifdef CONFIG_LOONGSON_UART_BASE
extern unsigned long _loongson_uart_base[], loongson_uart_base[];
extern void prom_init_loongson_uart_base(void);
#endif
static inline void prom_init_uart_base(void)
{
#ifdef CONFIG_LOONGSON_UART_BASE
prom_init_loongson_uart_base();
#endif
}
/* irq operation functions */
extern void bonito_irqdispatch(void);
extern void __init bonito_irq_init(void);
extern void __init mach_init_irq(void);
extern void mach_irq_dispatch(unsigned int pending);
extern int mach_i8259_irq(void);
......@@ -64,17 +47,6 @@ extern int mach_i8259_irq(void);
#define LOONGSON3_REG32(base, x) \
(*(volatile u32 *)((char *)TO_UNCAC(base) + (x)))
#define LOONGSON_IRQ_BASE 32
#define LOONGSON2_PERFCNT_IRQ (MIPS_CPU_IRQ_BASE + 6) /* cpu perf counter */
#include <linux/interrupt.h>
static inline void do_perfcnt_IRQ(void)
{
#if IS_ENABLED(CONFIG_OPROFILE)
do_IRQ(LOONGSON2_PERFCNT_IRQ);
#endif
}
#define LOONGSON_FLASH_BASE 0x1c000000
#define LOONGSON_FLASH_SIZE 0x02000000 /* 32M */
#define LOONGSON_FLASH_TOP (LOONGSON_FLASH_BASE+LOONGSON_FLASH_SIZE-1)
......@@ -109,11 +81,7 @@ static inline void do_perfcnt_IRQ(void)
#define LOONGSON_PCICFG_SIZE 0x00000800 /* 2K */
#define LOONGSON_PCICFG_TOP (LOONGSON_PCICFG_BASE+LOONGSON_PCICFG_SIZE-1)
#ifdef CONFIG_CPU_LOONGSON64
#define LOONGSON_PCIIO_BASE loongson_sysconf.pci_io_base
#else
#define LOONGSON_PCIIO_BASE 0x1fd00000
#endif
#define LOONGSON_PCIIO_SIZE 0x00100000 /* 1M */
#define LOONGSON_PCIIO_TOP (LOONGSON_PCIIO_BASE+LOONGSON_PCIIO_SIZE-1)
......@@ -270,86 +238,4 @@ extern u64 loongson_freqctrl[MAX_PACKAGES];
#define LOONGSON_PCIMAP_WIN(WIN, ADDR) \
((((ADDR)>>26) & LOONGSON_PCIMAP_PCIMAP_LO0) << ((WIN)*6))
#ifdef CONFIG_CPU_SUPPORTS_CPUFREQ
#include <linux/cpufreq.h>
extern struct cpufreq_frequency_table loongson2_clockmod_table[];
#endif
/*
* address windows configuration module
*
* loongson2e do not have this module
*/
#ifdef CONFIG_CPU_SUPPORTS_ADDRWINCFG
/* address window config module base address */
#define LOONGSON_ADDRWINCFG_BASE 0x3ff00000ul
#define LOONGSON_ADDRWINCFG_SIZE 0x180
extern unsigned long _loongson_addrwincfg_base;
#define LOONGSON_ADDRWINCFG(offset) \
(*(volatile u64 *)(_loongson_addrwincfg_base + (offset)))
#define CPU_WIN0_BASE LOONGSON_ADDRWINCFG(0x00)
#define CPU_WIN1_BASE LOONGSON_ADDRWINCFG(0x08)
#define CPU_WIN2_BASE LOONGSON_ADDRWINCFG(0x10)
#define CPU_WIN3_BASE LOONGSON_ADDRWINCFG(0x18)
#define CPU_WIN0_MASK LOONGSON_ADDRWINCFG(0x20)
#define CPU_WIN1_MASK LOONGSON_ADDRWINCFG(0x28)
#define CPU_WIN2_MASK LOONGSON_ADDRWINCFG(0x30)
#define CPU_WIN3_MASK LOONGSON_ADDRWINCFG(0x38)
#define CPU_WIN0_MMAP LOONGSON_ADDRWINCFG(0x40)
#define CPU_WIN1_MMAP LOONGSON_ADDRWINCFG(0x48)
#define CPU_WIN2_MMAP LOONGSON_ADDRWINCFG(0x50)
#define CPU_WIN3_MMAP LOONGSON_ADDRWINCFG(0x58)
#define PCIDMA_WIN0_BASE LOONGSON_ADDRWINCFG(0x60)
#define PCIDMA_WIN1_BASE LOONGSON_ADDRWINCFG(0x68)
#define PCIDMA_WIN2_BASE LOONGSON_ADDRWINCFG(0x70)
#define PCIDMA_WIN3_BASE LOONGSON_ADDRWINCFG(0x78)
#define PCIDMA_WIN0_MASK LOONGSON_ADDRWINCFG(0x80)
#define PCIDMA_WIN1_MASK LOONGSON_ADDRWINCFG(0x88)
#define PCIDMA_WIN2_MASK LOONGSON_ADDRWINCFG(0x90)
#define PCIDMA_WIN3_MASK LOONGSON_ADDRWINCFG(0x98)
#define PCIDMA_WIN0_MMAP LOONGSON_ADDRWINCFG(0xa0)
#define PCIDMA_WIN1_MMAP LOONGSON_ADDRWINCFG(0xa8)
#define PCIDMA_WIN2_MMAP LOONGSON_ADDRWINCFG(0xb0)
#define PCIDMA_WIN3_MMAP LOONGSON_ADDRWINCFG(0xb8)
#define ADDRWIN_WIN0 0
#define ADDRWIN_WIN1 1
#define ADDRWIN_WIN2 2
#define ADDRWIN_WIN3 3
#define ADDRWIN_MAP_DST_DDR 0
#define ADDRWIN_MAP_DST_PCI 1
#define ADDRWIN_MAP_DST_LIO 1
/*
* s: CPU, PCIDMA
* d: DDR, PCI, LIO
* win: 0, 1, 2, 3
* src: map source
* dst: map destination
* size: ~mask + 1
*/
#define LOONGSON_ADDRWIN_CFG(s, d, w, src, dst, size) do {\
s##_WIN##w##_BASE = (src); \
s##_WIN##w##_MMAP = (dst) | ADDRWIN_MAP_DST_##d; \
s##_WIN##w##_MASK = ~(size-1); \
} while (0)
#define LOONGSON_ADDRWIN_CPUTOPCI(win, src, dst, size) \
LOONGSON_ADDRWIN_CFG(CPU, PCI, win, src, dst, size)
#define LOONGSON_ADDRWIN_CPUTODDR(win, src, dst, size) \
LOONGSON_ADDRWIN_CFG(CPU, DDR, win, src, dst, size)
#define LOONGSON_ADDRWIN_PCITODDR(win, src, dst, size) \
LOONGSON_ADDRWIN_CFG(PCIDMA, DDR, win, src, dst, size)
#endif /* ! CONFIG_CPU_SUPPORTS_ADDRWINCFG */
#endif /* __ASM_MACH_LOONGSON64_LOONGSON_H */
arch/mips/include/asm/mach-loongson64/machine.h deleted 100644 → 0
View file @ 5831fdb0
/* SPDX-License-Identifier: GPL-2.0-or-later */
/*
* Copyright (C) 2009 Lemote, Inc.
* Author: Wu Zhangjin <wuzhangjin@gmail.com>
*/
#ifndef __ASM_MACH_LOONGSON64_MACHINE_H
#define __ASM_MACH_LOONGSON64_MACHINE_H
#ifdef CONFIG_LEMOTE_FULOONG2E
#define LOONGSON_MACHTYPE MACH_LEMOTE_FL2E
#endif
/* use fuloong2f as the default machine of LEMOTE_MACH2F */
#ifdef CONFIG_LEMOTE_MACH2F
#define LOONGSON_MACHTYPE MACH_LEMOTE_FL2F
#endif
#ifdef CONFIG_LOONGSON_MACH3X
#define LOONGSON_MACHTYPE MACH_LOONGSON_GENERIC
#endif /* CONFIG_LOONGSON_MACH3X */
#endif /* __ASM_MACH_LOONGSON64_MACHINE_H */
arch/mips/include/asm/mach-loongson64/mem.h deleted 100644 → 0
View file @ 5831fdb0
/* SPDX-License-Identifier: GPL-2.0-or-later */
/*
* Copyright (C) 2009 Lemote, Inc.
* Author: Wu Zhangjin <wuzhangjin@gmail.com>
*/
#ifndef __ASM_MACH_LOONGSON64_MEM_H
#define __ASM_MACH_LOONGSON64_MEM_H
/*
* high memory space
*
* in loongson2e, starts from 512M
* in loongson2f, starts from 2G 256M
*/
#ifdef CONFIG_CPU_LOONGSON2E
#define LOONGSON_HIGHMEM_START 0x20000000
#else
#define LOONGSON_HIGHMEM_START 0x90000000
#endif
/*
* the peripheral registers(MMIO):
*
* On the Lemote Loongson 2e system, reside between 0x1000:0000 and 0x2000:0000.
* On the Lemote Loongson 2f system, reside between 0x1000:0000 and 0x8000:0000.
*/
#define LOONGSON_MMIO_MEM_START 0x10000000
#ifdef CONFIG_CPU_LOONGSON2E
#define LOONGSON_MMIO_MEM_END 0x20000000
#else
#define LOONGSON_MMIO_MEM_END 0x80000000
#endif
#endif /* __ASM_MACH_LOONGSON64_MEM_H */
arch/mips/include/asm/mach-loongson64/mmzone.h
View file @ 1bdb7b76
......@@ -6,8 +6,8 @@
* Huacai Chen, chenhc@lemote.com
* Xiaofu Meng, Shuangshuang Zhang
*/
#ifndef _ASM_MACH_MMZONE_H
#define _ASM_MACH_MMZONE_H
#ifndef _ASM_MACH_LOONGSON64_MMZONE_H
#define _ASM_MACH_LOONGSON64_MMZONE_H
#include <boot_param.h>
#define NODE_ADDRSPACE_SHIFT 44
......@@ -19,30 +19,9 @@
#define pa_to_nid(addr) (((addr) & 0xf00000000000) >> NODE_ADDRSPACE_SHIFT)
#define nid_to_addrbase(nid) ((nid) << NODE_ADDRSPACE_SHIFT)
#define LEVELS_PER_SLICE 128
extern struct pglist_data *__node_data[];
struct slice_data {
unsigned long irq_enable_mask[2];
int level_to_irq[LEVELS_PER_SLICE];
};
struct hub_data {
cpumask_t h_cpus;
unsigned long slice_map;
unsigned long irq_alloc_mask[2];
struct slice_data slice[2];
};
struct node_data {
struct pglist_data pglist;
struct hub_data hub;
cpumask_t cpumask;
};
extern struct node_data *__node_data[];
#define NODE_DATA(n) (&__node_data[(n)]->pglist)
#define hub_data(n) (&__node_data[(n)]->hub)
#define NODE_DATA(n) (__node_data[n])
extern void setup_zero_pages(void);
extern void __init prom_init_numa_memory(void);
......
arch/mips/include/asm/mach-loongson64/pci.h
View file @ 1bdb7b76
......@@ -12,39 +12,8 @@ extern struct pci_ops loongson_pci_ops;
/* this is an offset from mips_io_port_base */
#define LOONGSON_PCI_IO_START 0x00004000UL
#ifdef CONFIG_CPU_SUPPORTS_ADDRWINCFG
/*
* we use address window2 to map cpu address space to pci space
* window2: cpu [1G, 2G] -> pci [1G, 2G]
* why not use window 0 & 1? because they are used by cpu when booting.
* window0: cpu [0, 256M] -> ddr [0, 256M]
* window1: cpu [256M, 512M] -> pci [256M, 512M]
*/
/* the smallest LOONGSON_CPU_MEM_SRC can be 512M */
#define LOONGSON_CPU_MEM_SRC 0x40000000ul /* 1G */
#define LOONGSON_PCI_MEM_DST LOONGSON_CPU_MEM_SRC
#define LOONGSON_PCI_MEM_START LOONGSON_PCI_MEM_DST
#define LOONGSON_PCI_MEM_END (0x80000000ul-1) /* 2G */
#define MMAP_CPUTOPCI_SIZE (LOONGSON_PCI_MEM_END - \
LOONGSON_PCI_MEM_START + 1)
#else /* loongson2f/32bit & loongson2e */
/* this pci memory space is mapped by pcimap in pci.c */
#ifdef CONFIG_CPU_LOONGSON64
#define LOONGSON_PCI_MEM_START 0x40000000UL
#define LOONGSON_PCI_MEM_END 0x7effffffUL
#else
#define LOONGSON_PCI_MEM_START LOONGSON_PCILO1_BASE
#define LOONGSON_PCI_MEM_END (LOONGSON_PCILO1_BASE + 0x04000000 * 2)
#endif
/* this is an offset from mips_io_port_base */
#define LOONGSON_PCI_IO_START 0x00004000UL
#endif /* !CONFIG_CPU_SUPPORTS_ADDRWINCFG */
#endif /* !__ASM_MACH_LOONGSON64_PCI_H_ */
arch/mips/include/asm/mach-loongson64/topology.h
View file @ 1bdb7b76
......@@ -5,7 +5,9 @@
#ifdef CONFIG_NUMA
#define cpu_to_node(cpu) (cpu_logical_map(cpu) >> 2)
#define cpumask_of_node(node) (&__node_data[(node)]->cpumask)
extern cpumask_t __node_cpumask[];
#define cpumask_of_node(node) (&__node_cpumask[node])
struct pci_bus;
extern int pcibus_to_node(struct pci_bus *);
......
arch/mips/loongson64/Kconfig
View file @ 1bdb7b76
......@@ -20,6 +20,7 @@ config LOONGSON_MACH3X
select I8259
select IRQ_MIPS_CPU
select NR_CPUS_DEFAULT_4
select USE_GENERIC_EARLY_PRINTK_8250
select SYS_HAS_CPU_LOONGSON64
select SYS_HAS_EARLY_PRINTK
select SYS_SUPPORTS_SMP
......@@ -30,7 +31,7 @@ config LOONGSON_MACH3X
select SYS_SUPPORTS_LITTLE_ENDIAN
select LOONGSON_MC146818
select ZONE_DMA32
select LEFI_FIRMWARE_INTERFACE
select NUMA
help
Generic Loongson 3 family machines utilize the 3A/3B revision
of Loongson processor and RS780/SBX00 chipset.
......@@ -48,16 +49,9 @@ config RS780_HPET
If unsure, say Yes.
config LOONGSON_UART_BASE
bool
default y
depends on EARLY_PRINTK || SERIAL_8250
config LOONGSON_MC146818
bool
default n
config LEFI_FIRMWARE_INTERFACE
bool
endif # MACH_LOONGSON64
arch/mips/loongson64/Platform
View file @ 1bdb7b76
......@@ -53,4 +53,4 @@ endif
platform-$(CONFIG_MACH_LOONGSON64) += loongson64/
cflags-$(CONFIG_MACH_LOONGSON64) += -I$(srctree)/arch/mips/include/asm/mach-loongson64 -mno-branch-likely
load-$(CONFIG_LOONGSON_MACH3X) += 0xffffffff80200000
load-$(CONFIG_CPU_LOONGSON64) += 0xffffffff80200000
arch/mips/loongson64/common/Makefile
View file @ 1bdb7b76
......@@ -3,15 +3,10 @@
# Makefile for loongson based machines.
#
obj-y += setup.o init.o cmdline.o env.o time.o reset.o irq.o \
bonito-irq.o mem.o machtype.o platform.o serial.o
obj-y += setup.o init.o cmdline.o env.o time.o reset.o
obj-$(CONFIG_PCI) += pci.o
#
# Serial port support
#
obj-$(CONFIG_EARLY_PRINTK) += early_printk.o
obj-$(CONFIG_LOONGSON_UART_BASE) += uart_base.o
obj-$(CONFIG_LOONGSON_MC146818) += rtc.o
#
......
arch/mips/loongson64/common/bonito-irq.c deleted 100644 → 0
View file @ 5831fdb0
// SPDX-License-Identifier: GPL-2.0-or-later
/*
* Copyright 2001 MontaVista Software Inc.
* Author: Jun Sun, jsun@mvista.com or jsun@junsun.net
* Copyright (C) 2000, 2001 Ralf Baechle (ralf@gnu.org)
*
* Copyright (C) 2007 Lemote Inc. & Institute of Computing Technology
* Author: Fuxin Zhang, zhangfx@lemote.com
*/
#include <linux/interrupt.h>
#include <linux/compiler.h>
#include <loongson.h>
static inline void bonito_irq_enable(struct irq_data *d)
{
LOONGSON_INTENSET = (1 << (d->irq - LOONGSON_IRQ_BASE));
mmiowb();
}
static inline void bonito_irq_disable(struct irq_data *d)
{
LOONGSON_INTENCLR = (1 << (d->irq - LOONGSON_IRQ_BASE));
mmiowb();
}
static struct irq_chip bonito_irq_type = {
.name = "bonito_irq",
.irq_mask = bonito_irq_disable,
.irq_unmask = bonito_irq_enable,
};
static struct irqaction __maybe_unused dma_timeout_irqaction = {
.handler = no_action,
.name = "dma_timeout",
};
void bonito_irq_init(void)
{
u32 i;
for (i = LOONGSON_IRQ_BASE; i < LOONGSON_IRQ_BASE + 32; i++)
irq_set_chip_and_handler(i, &bonito_irq_type,
handle_level_irq);
#ifdef CONFIG_CPU_LOONGSON2E
setup_irq(LOONGSON_IRQ_BASE + 10, &dma_timeout_irqaction);
#endif
}
arch/mips/loongson64/common/cmdline.c
View file @ 1bdb7b76
......@@ -39,6 +39,4 @@ void __init prom_init_cmdline(void)
strcat(arcs_cmdline, ((char *)l));
strcat(arcs_cmdline, " ");
}
prom_init_machtype();
}
arch/mips/loongson64/common/early_printk.c deleted 100644 → 0
View file @ 5831fdb0
// SPDX-License-Identifier: GPL-2.0-or-later
/* early printk support
*
* Copyright (c) 2009 Philippe Vachon <philippe@cowpig.ca>
* Copyright (c) 2009 Lemote Inc.
* Author: Wu Zhangjin, wuzhangjin@gmail.com
*/
#include <linux/serial_reg.h>
#include <asm/setup.h>
#include <loongson.h>
#define PORT(base, offset) (u8 *)(base + offset)
static inline unsigned int serial_in(unsigned char *base, int offset)
{
return readb(PORT(base, offset));
}
static inline void serial_out(unsigned char *base, int offset, int value)
{
writeb(value, PORT(base, offset));
}
void prom_putchar(char c)
{
int timeout;
unsigned char *uart_base;
uart_base = (unsigned char *)_loongson_uart_base[0];
timeout = 1024;
while (((serial_in(uart_base, UART_LSR) & UART_LSR_THRE) == 0) &&
(timeout-- > 0))
;
serial_out(uart_base, UART_TX, c);
}
arch/mips/loongson64/common/env.c
View file @ 1bdb7b76
......@@ -30,41 +30,13 @@ u64 loongson_freqctrl[MAX_PACKAGES];
unsigned long long smp_group[4];
#define parse_even_earlier(res, option, p) \
do { \
unsigned int tmp __maybe_unused; \
\
if (strncmp(option, (char *)p, strlen(option)) == 0) \
tmp = kstrtou32((char *)p + strlen(option"="), 10, &res); \
} while (0)
const char *get_system_type(void)
{
return "Generic Loongson64 System";
}
void __init prom_init_env(void)
{
/* pmon passes arguments in 32bit pointers */
unsigned int processor_id;
#ifndef CONFIG_LEFI_FIRMWARE_INTERFACE
int *_prom_envp;
long l;
/* firmware arguments are initialized in head.S */
_prom_envp = (int *)fw_arg2;
l = (long)*_prom_envp;
while (l != 0) {
parse_even_earlier(cpu_clock_freq, "cpuclock", l);
parse_even_earlier(memsize, "memsize", l);
parse_even_earlier(highmemsize, "highmemsize", l);
_prom_envp++;
l = (long)*_prom_envp;
}
if (memsize == 0)
memsize = 256;
loongson_sysconf.nr_uarts = 1;
pr_info("memsize=%u, highmemsize=%u\n", memsize, highmemsize);
#else
struct boot_params *boot_p;
struct loongson_params *loongson_p;
struct system_loongson *esys;
......@@ -182,31 +154,5 @@ void __init prom_init_env(void)
if (loongson_sysconf.nr_sensors)
memcpy(loongson_sysconf.sensors, esys->sensors,
sizeof(struct sensor_device) * loongson_sysconf.nr_sensors);
#endif
if (cpu_clock_freq == 0) {
processor_id = (&current_cpu_data)->processor_id;
switch (processor_id & PRID_REV_MASK) {
case PRID_REV_LOONGSON2E:
cpu_clock_freq = 533080000;
break;
case PRID_REV_LOONGSON2F:
cpu_clock_freq = 797000000;
break;
case PRID_REV_LOONGSON3A_R1:
case PRID_REV_LOONGSON3A_R2_0:
case PRID_REV_LOONGSON3A_R2_1:
case PRID_REV_LOONGSON3A_R3_0:
case PRID_REV_LOONGSON3A_R3_1:
cpu_clock_freq = 900000000;
break;
case PRID_REV_LOONGSON3B_R1:
case PRID_REV_LOONGSON3B_R2:
cpu_clock_freq = 1000000000;
break;
default:
cpu_clock_freq = 100000000;
break;
}
}
pr_info("CpuClock = %u\n", cpu_clock_freq);
}
arch/mips/loongson64/common/init.c
View file @ 1bdb7b76
......@@ -12,9 +12,6 @@
#include <loongson.h>
/* Loongson CPU address windows config space base address */
unsigned long __maybe_unused _loongson_addrwincfg_base;
static void __init mips_nmi_setup(void)
{
void *base;
......@@ -27,11 +24,6 @@ static void __init mips_nmi_setup(void)
void __init prom_init(void)
{
#ifdef CONFIG_CPU_SUPPORTS_ADDRWINCFG
_loongson_addrwincfg_base = (unsigned long)
ioremap(LOONGSON_ADDRWINCFG_BASE, LOONGSON_ADDRWINCFG_SIZE);
#endif
prom_init_cmdline();
prom_init_env();
......@@ -39,14 +31,11 @@ void __init prom_init(void)
set_io_port_base((unsigned long)
ioremap(LOONGSON_PCIIO_BASE, LOONGSON_PCIIO_SIZE));
#ifdef CONFIG_NUMA
prom_init_numa_memory();
#else
prom_init_memory();
#endif
/*init the uart base address */
prom_init_uart_base();
/* Hardcode to CPU UART 0 */
setup_8250_early_printk_port(TO_UNCAC(LOONGSON_REG_BASE + 0x1e0), 0, 1024);
register_smp_ops(&loongson3_smp_ops);
board_nmi_handler_setup = mips_nmi_setup;
}
......
arch/mips/loongson64/common/irq.c deleted 100644 → 0
View file @ 5831fdb0
// SPDX-License-Identifier: GPL-2.0-or-later
/*
* Copyright (C) 2007 Lemote Inc. & Institute of Computing Technology
* Author: Fuxin Zhang, zhangfx@lemote.com
*/
#include <linux/delay.h>
#include <linux/interrupt.h>
#include <loongson.h>
/*
* the first level int-handler will jump here if it is a bonito irq
*/
void bonito_irqdispatch(void)
{
u32 int_status;
int i;
/* workaround the IO dma problem: let cpu looping to allow DMA finish */
int_status = LOONGSON_INTISR;
while (int_status & (1 << 10)) {
udelay(1);
int_status = LOONGSON_INTISR;
}
/* Get pending sources, masked by current enables */
int_status = LOONGSON_INTISR & LOONGSON_INTEN;
if (int_status) {
i = __ffs(int_status);
do_IRQ(LOONGSON_IRQ_BASE + i);
}
}
asmlinkage void plat_irq_dispatch(void)
{
unsigned int pending;
pending = read_c0_cause() & read_c0_status() & ST0_IM;
/* machine-specific plat_irq_dispatch */
mach_irq_dispatch(pending);
}
void __init arch_init_irq(void)
{
/*
* Clear all of the interrupts while we change the able around a bit.
* int-handler is not on bootstrap
*/
clear_c0_status(ST0_IM | ST0_BEV);
/* no steer */
LOONGSON_INTSTEER = 0;
/*
* Mask out all interrupt by writing "1" to all bit position in
* the interrupt reset reg.
*/
LOONGSON_INTENCLR = ~0;
/* machine specific irq init */
mach_init_irq();
}
arch/mips/loongson64/common/machtype.c deleted 100644 → 0
View file @ 5831fdb0
// SPDX-License-Identifier: GPL-2.0-or-later
/*
* Copyright (C) 2009 Lemote Inc.
* Author: Wu Zhangjin, wuzhangjin@gmail.com
*
* Copyright (c) 2009 Zhang Le <r0bertz@gentoo.org>
*/
#include <linux/errno.h>
#include <asm/bootinfo.h>
#include <loongson.h>
#include <machine.h>
/* please ensure the length of the machtype string is less than 50 */
#define MACHTYPE_LEN 50
static const char *system_types[] = {
[MACH_LOONGSON_UNKNOWN] = "unknown loongson machine",
[MACH_LEMOTE_FL2E] = "lemote-fuloong-2e-box",
[MACH_LEMOTE_FL2F] = "lemote-fuloong-2f-box",
[MACH_LEMOTE_ML2F7] = "lemote-mengloong-2f-7inches",
[MACH_LEMOTE_YL2F89] = "lemote-yeeloong-2f-8.9inches",
[MACH_DEXXON_GDIUM2F10] = "dexxon-gdium-2f",
[MACH_LEMOTE_NAS] = "lemote-nas-2f",
[MACH_LEMOTE_LL2F] = "lemote-lynloong-2f",
[MACH_LOONGSON_GENERIC] = "generic-loongson-machine",
[MACH_LOONGSON_END] = NULL,
};
const char *get_system_type(void)
{
return system_types[mips_machtype];
}
void __weak __init mach_prom_init_machtype(void)
{
}
void __init prom_init_machtype(void)
{
char *p, str[MACHTYPE_LEN + 1];
int machtype = MACH_LEMOTE_FL2E;
mips_machtype = LOONGSON_MACHTYPE;
p = strstr(arcs_cmdline, "machtype=");
if (!p) {
mach_prom_init_machtype();
return;
}
p += strlen("machtype=");
strncpy(str, p, MACHTYPE_LEN);
str[MACHTYPE_LEN] = '\0';
p = strstr(str, " ");
if (p)
*p = '\0';
for (; system_types[machtype]; machtype++)
if (strstr(system_types[machtype], str)) {
mips_machtype = machtype;
break;
}
}
arch/mips/loongson64/common/mem.c deleted 100644 → 0
View file @ 5831fdb0
// SPDX-License-Identifier: GPL-2.0-or-later
/*
*/
#include <linux/fs.h>
#include <linux/fcntl.h>
#include <linux/memblock.h>
#include <linux/mm.h>
#include <asm/bootinfo.h>
#include <loongson.h>
#include <boot_param.h>
#include <mem.h>
#include <pci.h>
#ifndef CONFIG_LEFI_FIRMWARE_INTERFACE
u32 memsize, highmemsize;
void __init prom_init_memory(void)
{
add_memory_region(0x0, (memsize << 20), BOOT_MEM_RAM);
add_memory_region(memsize << 20, LOONGSON_PCI_MEM_START - (memsize <<
20), BOOT_MEM_RESERVED);
#ifdef CONFIG_CPU_SUPPORTS_ADDRWINCFG
{
int bit;
bit = fls(memsize + highmemsize);
if (bit != ffs(memsize + highmemsize))
bit += 20;
else
bit = bit + 20 - 1;
/* set cpu window3 to map CPU to DDR: 2G -> 2G */
LOONGSON_ADDRWIN_CPUTODDR(ADDRWIN_WIN3, 0x80000000ul,
0x80000000ul, (1 << bit));
mmiowb();
}
#endif /* !CONFIG_CPU_SUPPORTS_ADDRWINCFG */
#ifdef CONFIG_64BIT
if (highmemsize > 0)
add_memory_region(LOONGSON_HIGHMEM_START,
highmemsize << 20, BOOT_MEM_RAM);
add_memory_region(LOONGSON_PCI_MEM_END + 1, LOONGSON_HIGHMEM_START -
LOONGSON_PCI_MEM_END - 1, BOOT_MEM_RESERVED);
#endif /* !CONFIG_64BIT */
}
#else /* CONFIG_LEFI_FIRMWARE_INTERFACE */
void __init prom_init_memory(void)
{
int i;
u32 node_id;
u32 mem_type;
/* parse memory information */
for (i = 0; i < loongson_memmap->nr_map; i++) {
node_id = loongson_memmap->map[i].node_id;
mem_type = loongson_memmap->map[i].mem_type;
if (node_id != 0)
continue;
switch (mem_type) {
case SYSTEM_RAM_LOW:
memblock_add(loongson_memmap->map[i].mem_start,
(u64)loongson_memmap->map[i].mem_size << 20);
break;
case SYSTEM_RAM_HIGH:
memblock_add(loongson_memmap->map[i].mem_start,
(u64)loongson_memmap->map[i].mem_size << 20);
break;
case SYSTEM_RAM_RESERVED:
memblock_reserve(loongson_memmap->map[i].mem_start,
(u64)loongson_memmap->map[i].mem_size << 20);
break;
}
}
}
#endif /* CONFIG_LEFI_FIRMWARE_INTERFACE */
/* override of arch/mips/mm/cache.c: __uncached_access */
int __uncached_access(struct file *file, unsigned long addr)
{
if (file->f_flags & O_DSYNC)
return 1;
return addr >= __pa(high_memory) ||
((addr >= LOONGSON_MMIO_MEM_START) &&
(addr < LOONGSON_MMIO_MEM_END));
}
#ifdef CONFIG_CPU_SUPPORTS_UNCACHED_ACCELERATED
#include <linux/pci.h>
#include <linux/sched.h>
#include <asm/current.h>
static unsigned long uca_start, uca_end;
pgprot_t phys_mem_access_prot(struct file *file, unsigned long pfn,
unsigned long size, pgprot_t vma_prot)
{
unsigned long offset = pfn << PAGE_SHIFT;
unsigned long end = offset + size;
if (__uncached_access(file, offset)) {
if (uca_start && (offset >= uca_start) &&
(end <= uca_end))
return __pgprot((pgprot_val(vma_prot) &
~_CACHE_MASK) |
_CACHE_UNCACHED_ACCELERATED);
else
return pgprot_noncached(vma_prot);
}
return vma_prot;
}
static int __init find_vga_mem_init(void)
{
struct pci_dev *dev = 0;
struct resource *r;
int idx;
if (uca_start)
return 0;
for_each_pci_dev(dev) {
if ((dev->class >> 16) == PCI_BASE_CLASS_DISPLAY) {
for (idx = 0; idx < PCI_NUM_RESOURCES; idx++) {
r = &dev->resource[idx];
if (!r->start && r->end)
continue;
if (r->flags & IORESOURCE_IO)
continue;
if (r->flags & IORESOURCE_MEM) {
uca_start = r->start;
uca_end = r->end;
return 0;
}
}
}
}
return 0;
}
late_initcall(find_vga_mem_init);
#endif /* !CONFIG_CPU_SUPPORTS_UNCACHED_ACCELERATED */
arch/mips/loongson64/common/pci.c
View file @ 1bdb7b76
......@@ -81,15 +81,12 @@ static int __init pcibios_init(void)
setup_pcimap();
loongson_pci_controller.io_map_base = mips_io_port_base;
#ifdef CONFIG_LEFI_FIRMWARE_INTERFACE
loongson_pci_mem_resource.start = loongson_sysconf.pci_mem_start_addr;
loongson_pci_mem_resource.end = loongson_sysconf.pci_mem_end_addr;
#endif
register_pci_controller(&loongson_pci_controller);
#ifdef CONFIG_CPU_LOONGSON64
sbx00_acpi_init();
#endif
return 0;
}
......
arch/mips/loongson64/common/platform.c deleted 100644 → 0
View file @ 5831fdb0
// SPDX-License-Identifier: GPL-2.0-or-later
/*
* Copyright (C) 2009 Lemote Inc.
* Author: Wu Zhangjin, wuzhangjin@gmail.com
*/
#include <linux/err.h>
#include <linux/smp.h>
#include <linux/platform_device.h>
static struct platform_device loongson2_cpufreq_device = {
.name = "loongson2_cpufreq",
.id = -1,
};
static int __init loongson2_cpufreq_init(void)
{
struct cpuinfo_mips *c = &current_cpu_data;
/* Only 2F revision and it's successors support CPUFreq */
if ((c->processor_id & PRID_REV_MASK) >= PRID_REV_LOONGSON2F)
return platform_device_register(&loongson2_cpufreq_device);
return -ENODEV;
}
arch_initcall(loongson2_cpufreq_init);
arch/mips/loongson64/common/pm.c
View file @ 1bdb7b76
......@@ -60,56 +60,6 @@ void __weak setup_wakeup_events(void)
{
}
/*
* Check wakeup events
*/
int __weak wakeup_loongson(void)
{
return 1;
}
/*
* If the events are really what we want to wakeup the CPU, wake it up
* otherwise put the CPU asleep again.
*/
static void wait_for_wakeup_events(void)
{
while (!wakeup_loongson())
LOONGSON_CHIPCFG(0) &= ~0x7;
}
/*
* Stop all perf counters
*
* $24 is the control register of Loongson perf counter
*/
static inline void stop_perf_counters(void)
{
__write_64bit_c0_register($24, 0, 0);
}
static void loongson_suspend_enter(void)
{
static unsigned int cached_cpu_freq;
/* setup wakeup events via enabling the IRQs */
setup_wakeup_events();
stop_perf_counters();
cached_cpu_freq = LOONGSON_CHIPCFG(0);
/* Put CPU into wait mode */
LOONGSON_CHIPCFG(0) &= ~0x7;
/* wait for the given events to wakeup cpu from wait mode */
wait_for_wakeup_events();
LOONGSON_CHIPCFG(0) = cached_cpu_freq;
mmiowb();
}
void __weak mach_suspend(void)
{
}
......@@ -122,9 +72,6 @@ static int loongson_pm_enter(suspend_state_t state)
{
mach_suspend();
/* processor specific suspend */
loongson_suspend_enter();
mach_resume();
return 0;
......
arch/mips/loongson64/common/reset.c
View file @ 1bdb7b76
......@@ -17,31 +17,12 @@
static inline void loongson_reboot(void)
{
#ifndef CONFIG_CPU_JUMP_WORKAROUNDS
((void (*)(void))ioremap_nocache(LOONGSON_BOOT_BASE, 4)) ();
#else
void (*func)(void);
func = (void *)ioremap_nocache(LOONGSON_BOOT_BASE, 4);
__asm__ __volatile__(
" .set noat \n"
" jr %[func] \n"
" .set at \n"
: /* No outputs */
: [func] "r" (func));
#endif
}
static void loongson_restart(char *command)
{
#ifndef CONFIG_LEFI_FIRMWARE_INTERFACE
/* do preparation for reboot */
mach_prepare_reboot();
/* reboot via jumping to boot base address */
loongson_reboot();
#else
void (*fw_restart)(void) = (void *)loongson_sysconf.restart_addr;
fw_restart();
......@@ -49,20 +30,10 @@ static void loongson_restart(char *command)
if (cpu_wait)
cpu_wait();
}
#endif
}
static void loongson_poweroff(void)
{
#ifndef CONFIG_LEFI_FIRMWARE_INTERFACE
mach_prepare_shutdown();
/*
* It needs a wait loop here, but mips/kernel/reset.c already calls
* a generic delay loop, machine_hang(), so simply return.
*/
return;
#else
void (*fw_poweroff)(void) = (void *)loongson_sysconf.poweroff_addr;
fw_poweroff();
......@@ -70,7 +41,6 @@ static void loongson_poweroff(void)
if (cpu_wait)
cpu_wait();
}
#endif
}
static void loongson_halt(void)
......
arch/mips/loongson64/common/serial.c deleted 100644 → 0
View file @ 5831fdb0
/*
* This file is subject to the terms and conditions of the GNU General Public
* License. See the file "COPYING" in the main directory of this archive
* for more details.
*
* Copyright (C) 2007 Ralf Baechle (ralf@linux-mips.org)
*
* Copyright (C) 2009 Lemote, Inc.
* Author: Yan hua (yanhua@lemote.com)
* Author: Wu Zhangjin (wuzhangjin@gmail.com)
*/
#include <linux/io.h>
#include <linux/module.h>
#include <linux/serial_8250.h>
#include <asm/bootinfo.h>
#include <loongson.h>
#include <machine.h>
#define PORT(int, clk) \
{ \
.irq = int, \
.uartclk = clk, \
.iotype = UPIO_PORT, \
.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, \
.regshift = 0, \
}
#define PORT_M(int, clk) \
{ \
.irq = MIPS_CPU_IRQ_BASE + (int), \
.uartclk = clk, \
.iotype = UPIO_MEM, \
.membase = (void __iomem *)NULL, \
.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, \
.regshift = 0, \
}
static struct plat_serial8250_port uart8250_data[][MAX_UARTS + 1] = {
[MACH_LOONGSON_UNKNOWN] = {},
[MACH_LEMOTE_FL2E] = {PORT(4, 1843200), {} },
[MACH_LEMOTE_FL2F] = {PORT(3, 1843200), {} },
[MACH_LEMOTE_ML2F7] = {PORT_M(3, 3686400), {} },
[MACH_LEMOTE_YL2F89] = {PORT_M(3, 3686400), {} },
[MACH_DEXXON_GDIUM2F10] = {PORT_M(3, 3686400), {} },
[MACH_LEMOTE_NAS] = {PORT_M(3, 3686400), {} },
[MACH_LEMOTE_LL2F] = {PORT(3, 1843200), {} },
[MACH_LOONGSON_GENERIC] = {PORT_M(2, 25000000), {} },
[MACH_LOONGSON_END] = {},
};
static struct platform_device uart8250_device = {
.name = "serial8250",
.id = PLAT8250_DEV_PLATFORM,
};
static int __init serial_init(void)
{
int i;
unsigned char iotype;
iotype = uart8250_data[mips_machtype][0].iotype;
if (UPIO_MEM == iotype) {
uart8250_data[mips_machtype][0].mapbase =
loongson_uart_base[0];
uart8250_data[mips_machtype][0].membase =
(void __iomem *)_loongson_uart_base[0];
}
else if (UPIO_PORT == iotype)
uart8250_data[mips_machtype][0].iobase =
loongson_uart_base[0] - LOONGSON_PCIIO_BASE;
if (loongson_sysconf.uarts[0].uartclk)
uart8250_data[mips_machtype][0].uartclk =
loongson_sysconf.uarts[0].uartclk;
for (i = 1; i < loongson_sysconf.nr_uarts; i++) {
iotype = loongson_sysconf.uarts[i].iotype;
uart8250_data[mips_machtype][i].iotype = iotype;
loongson_uart_base[i] = loongson_sysconf.uarts[i].uart_base;
if (UPIO_MEM == iotype) {
uart8250_data[mips_machtype][i].irq =
MIPS_CPU_IRQ_BASE + loongson_sysconf.uarts[i].int_offset;
uart8250_data[mips_machtype][i].mapbase =
loongson_uart_base[i];
uart8250_data[mips_machtype][i].membase =
ioremap_nocache(loongson_uart_base[i], 8);
} else if (UPIO_PORT == iotype) {
uart8250_data[mips_machtype][i].irq =
loongson_sysconf.uarts[i].int_offset;
uart8250_data[mips_machtype][i].iobase =
loongson_uart_base[i] - LOONGSON_PCIIO_BASE;
}
uart8250_data[mips_machtype][i].uartclk =
loongson_sysconf.uarts[i].uartclk;
uart8250_data[mips_machtype][i].flags =
UPF_BOOT_AUTOCONF | UPF_SKIP_TEST;
}
memset(&uart8250_data[mips_machtype][loongson_sysconf.nr_uarts],
0, sizeof(struct plat_serial8250_port));
uart8250_device.dev.platform_data = uart8250_data[mips_machtype];
return platform_device_register(&uart8250_device);
}
module_init(serial_init);
static void __exit serial_exit(void)
{
platform_device_unregister(&uart8250_device);
}
module_exit(serial_exit);
arch/mips/loongson64/common/setup.c
View file @ 1bdb7b76
......@@ -11,11 +11,6 @@
#include <loongson.h>
#ifdef CONFIG_VT
#include <linux/console.h>
#include <linux/screen_info.h>
#endif
static void wbflush_loongson(void)
{
asm(".set\tpush\n\t"
......@@ -32,20 +27,4 @@ EXPORT_SYMBOL(__wbflush);
void __init plat_mem_setup(void)
{
#ifdef CONFIG_VT
#if defined(CONFIG_VGA_CONSOLE)
conswitchp = &vga_con;
screen_info = (struct screen_info) {
.orig_x = 0,
.orig_y = 25,
.orig_video_cols = 80,
.orig_video_lines = 25,
.orig_video_isVGA = VIDEO_TYPE_VGAC,
.orig_video_points = 16,
};
#elif defined(CONFIG_DUMMY_CONSOLE)
conswitchp = &dummy_con;
#endif
#endif
}
arch/mips/loongson64/common/time.c
View file @ 1bdb7b76
......@@ -11,7 +11,6 @@
#include <asm/hpet.h>
#include <loongson.h>
#include <cs5536/cs5536_mfgpt.h>
void __init plat_time_init(void)
{
......@@ -20,8 +19,6 @@ void __init plat_time_init(void)
#ifdef CONFIG_RS780_HPET
setup_hpet_timer();
#else
setup_mfgpt0_timer();
#endif
}
......
arch/mips/loongson64/common/uart_base.c deleted 100644 → 0
View file @ 5831fdb0
// SPDX-License-Identifier: GPL-2.0-or-later
/*
* Copyright (C) 2009 Lemote Inc.
* Author: Wu Zhangjin, wuzhangjin@gmail.com
*/
#include <linux/export.h>
#include <asm/bootinfo.h>
#include <loongson.h>
/* raw */
unsigned long loongson_uart_base[MAX_UARTS] = {};
/* ioremapped */
unsigned long _loongson_uart_base[MAX_UARTS] = {};
EXPORT_SYMBOL(loongson_uart_base);
EXPORT_SYMBOL(_loongson_uart_base);
void prom_init_loongson_uart_base(void)
{
switch (mips_machtype) {
case MACH_LOONGSON_GENERIC:
/* The CPU provided serial port (CPU) */
loongson_uart_base[0] = LOONGSON_REG_BASE + 0x1e0;
break;
case MACH_LEMOTE_FL2E:
loongson_uart_base[0] = LOONGSON_PCIIO_BASE + 0x3f8;
break;
case MACH_LEMOTE_FL2F:
case MACH_LEMOTE_LL2F:
loongson_uart_base[0] = LOONGSON_PCIIO_BASE + 0x2f8;
break;
case MACH_LEMOTE_ML2F7:
case MACH_LEMOTE_YL2F89:
case MACH_DEXXON_GDIUM2F10:
case MACH_LEMOTE_NAS:
default:
/* The CPU provided serial port (LPC) */
loongson_uart_base[0] = LOONGSON_LIO1_BASE + 0x3f8;
break;
}
_loongson_uart_base[0] =
(unsigned long)ioremap_nocache(loongson_uart_base[0], 8);
}
arch/mips/loongson64/loongson-3/irq.c
View file @ 1bdb7b76
......@@ -78,8 +78,12 @@ static void ht_irqdispatch(void)
#define UNUSED_IPS (CAUSEF_IP5 | CAUSEF_IP4 | CAUSEF_IP1 | CAUSEF_IP0)
void mach_irq_dispatch(unsigned int pending)
asmlinkage void plat_irq_dispatch(void)
{
unsigned int pending;
pending = read_c0_cause() & read_c0_status() & ST0_IM;
if (pending & CAUSEF_IP7)
do_IRQ(LOONGSON_TIMER_IRQ);
#if defined(CONFIG_SMP)
......@@ -127,7 +131,7 @@ void irq_router_init(void)
LOONGSON_INT_ROUTER_INTEN | (0xffff << 16) | 0x1 << 10;
}
void __init mach_init_irq(void)
void __init arch_init_irq(void)
{
struct irq_chip *chip;
......
arch/mips/loongson64/loongson-3/numa.c
View file @ 1bdb7b76
......@@ -26,12 +26,15 @@
#include <asm/wbflush.h>
#include <boot_param.h>
static struct node_data prealloc__node_data[MAX_NUMNODES];
static struct pglist_data prealloc__node_data[MAX_NUMNODES];
unsigned char __node_distances[MAX_NUMNODES][MAX_NUMNODES];
EXPORT_SYMBOL(__node_distances);
struct node_data *__node_data[MAX_NUMNODES];
struct pglist_data *__node_data[MAX_NUMNODES];
EXPORT_SYMBOL(__node_data);
cpumask_t __node_cpumask[MAX_NUMNODES];
EXPORT_SYMBOL(__node_cpumask);
static void enable_lpa(void)
{
unsigned long value;
......@@ -214,7 +217,7 @@ static __init void prom_meminit(void)
if (node_online(node)) {
szmem(node);
node_mem_init(node);
cpumask_clear(&__node_data[(node)]->cpumask);
cpumask_clear(&__node_cpumask[node]);
}
}
memblocks_present();
......@@ -228,7 +231,7 @@ static __init void prom_meminit(void)
if (loongson_sysconf.reserved_cpus_mask & (1<<cpu))
continue;
cpumask_set_cpu(active_cpu, &__node_data[(node)]->cpumask);
cpumask_set_cpu(active_cpu, &__node_cpumask[node]);
pr_info("NUMA: set cpumask cpu %d on node %d\n", active_cpu, node);
active_cpu++;
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7