powerpc/mpc85xx: Add BSC9132 QDS Support

- BSC9132 is an integrated device that targets Femto base station market.
  It combines Power Architecture e500v2 and DSP StarCore SC3850 technologies
  with MAPLE-B2F baseband acceleration processing elements

- BSC9132QDS Overview
     2Gbyte DDR3 (on board DDR)
     32Mbyte 16bit NOR flash
     128Mbyte 2K page size NAND Flash
     256 Kbit M24256 I2C EEPROM
     128 Mbit SPI Flash memory
     SD slot
     eTSEC1: Connected to SGMII PHY
     eTSEC2: Connected to SGMII PHY
     DUART interface: supports one UARTs up to 115200 bps for console display
Signed-off-by: Harninder Rai <harninder.rai@freescale.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>

Documentation/devicetree/bindings/powerpc/fsl/board.txt

@@ -67,3 +67,20 @@ Example:
 			gpio-controller;
 		};
 	};
+
+* Freescale on-board FPGA connected on I2C bus
+
+Some Freescale boards like BSC9132QDS have on board FPGA connected on
+the i2c bus.
+
+Required properties:
+- compatible: Should be a board-specific string followed by a string
+  indicating the type of FPGA.  Example:
+	"fsl,<board>-fpga", "fsl,fpga-qixis-i2c"
+- reg: Should contain the address of the FPGA
+
+Example:
+	fpga: fpga@66 {
+		compatible = "fsl,bsc9132qds-fpga", "fsl,fpga-qixis-i2c";
+		reg = <0x66>;
+	};

arch/powerpc/boot/dts/bsc9132qds.dts

+/*
+ * BSC9132 QDS Device Tree Source
+ *
+ * Copyright 2014 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+/include/ "fsl/bsc9132si-pre.dtsi"
+
+/ {
+	model = "fsl,bsc9132qds";
+	compatible = "fsl,bsc9132qds";
+
+	memory {
+		device_type = "memory";
+	};
+
+	ifc: ifc@ff71e000 {
+		/* NOR, NAND Flash on board */
+		ranges = <0x0 0x0 0x0 0x88000000 0x08000000
+			  0x1 0x0 0x0 0xff800000 0x00010000>;
+		reg = <0x0 0xff71e000 0x0 0x2000>;
+	};
+
+	soc: soc@ff700000 {
+		ranges = <0x0 0x0 0xff700000 0x100000>;
+	};
+};
+
+/include/ "bsc9132qds.dtsi"
+/include/ "fsl/bsc9132si-post.dtsi"

arch/powerpc/boot/dts/bsc9132qds.dtsi

+/*
+ * BSC9132 QDS Device Tree Source stub (no addresses or top-level ranges)
+ *
+ * Copyright 2014 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *       notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *       notice, this list of conditions and the following disclaimer in the
+ *       documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *       names of its contributors may be used to endorse or promote products
+ *       derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&ifc {
+	nor@0,0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "cfi-flash";
+		reg = <0x0 0x0 0x8000000>;
+		bank-width = <2>;
+		device-width = <1>;
+	};
+
+	nand@1,0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "fsl,ifc-nand";
+		reg = <0x1 0x0 0x4000>;
+	};
+};
+
+&soc {
+	spi@7000 {
+		flash@0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "spansion,s25sl12801";
+			reg = <0>;
+			spi-max-frequency = <30000000>;
+		};
+	};
+
+	i2c@3000 {
+		fpga: fpga@66 {
+			compatible = "fsl,bsc9132qds-fpga", "fsl,fpga-qixis-i2c";
+			reg = <0x66>;
+		};
+	};
+
+	usb@22000 {
+		phy_type = "ulpi";
+	};
+
+	mdio@24000 {
+		phy0: ethernet-phy@0 {
+			reg = <0x0>;
+		};
+
+		phy1: ethernet-phy@1 {
+			reg = <0x1>;
+		};
+
+		tbi0: tbi-phy@11 {
+			reg = <0x1f>;
+			device_type = "tbi-phy";
+		};
+	};
+
+	enet0: ethernet@b0000 {
+		phy-handle = <&phy0>;
+		tbi-handle = <&tbi0>;
+		phy-connection-type = "sgmii";
+	};
+
+	enet1: ethernet@b1000 {
+		phy-handle = <&phy1>;
+		tbi-handle = <&tbi0>;
+		phy-connection-type = "sgmii";
+	};
+};

arch/powerpc/boot/dts/fsl/bsc9132si-post.dtsi

+/*
+ * BSC9132 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2014 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *       notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *       notice, this list of conditions and the following disclaimer in the
+ *       documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *       names of its contributors may be used to endorse or promote products
+ *       derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&ifc {
+	#address-cells = <2>;
+	#size-cells = <1>;
+	compatible = "fsl,ifc", "simple-bus";
+	/* FIXME: Test whether interrupts are split */
+	interrupts = <16 2 0 0 20 2 0 0>;
+};
+
+&soc {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	device_type = "soc";
+	compatible = "fsl,bsc9132-immr", "simple-bus";
+	bus-frequency = <0>;		// Filled out by uboot.
+
+	ecm-law@0 {
+		compatible = "fsl,ecm-law";
+		reg = <0x0 0x1000>;
+		fsl,num-laws = <12>;
+	};
+
+	ecm@1000 {
+		compatible = "fsl,bsc9132-ecm", "fsl,ecm";
+		reg = <0x1000 0x1000>;
+		interrupts = <16 2 0 0>;
+	};
+
+	memory-controller@2000 {
+		compatible = "fsl,bsc9132-memory-controller";
+		reg = <0x2000 0x1000>;
+		interrupts = <16 2 1 8>;
+	};
+
+/include/ "pq3-i2c-0.dtsi"
+	i2c@3000 {
+		interrupts = <17 2 0 0>;
+	};
+
+/include/ "pq3-i2c-1.dtsi"
+	i2c@3100 {
+		interrupts = <17 2 0 0>;
+	};
+
+/include/ "pq3-duart-0.dtsi"
+	serial0: serial@4500 {
+		interrupts = <18 2 0 0>;
+	};
+
+	serial1: serial@4600 {
+		interrupts = <18 2 0 0 >;
+	};
+/include/ "pq3-espi-0.dtsi"
+	spi0: spi@7000 {
+		fsl,espi-num-chipselects = <1>;
+		interrupts = <22 0x2 0 0>;
+	};
+
+/include/ "pq3-gpio-0.dtsi"
+	gpio-controller@f000 {
+		interrupts = <19 0x2 0 0>;
+		};
+
+	L2: l2-cache-controller@20000 {
+		compatible = "fsl,bsc9132-l2-cache-controller";
+		reg = <0x20000 0x1000>;
+		cache-line-size = <32>;	// 32 bytes
+		cache-size = <0x40000>; // L2,256K
+		interrupts = <16 2 1 0>;
+	};
+
+/include/ "pq3-dma-0.dtsi"
+
+dma@21300 {
+
+	dma-channel@0 {
+		interrupts = <62 2 0 0>;
+	};
+
+	dma-channel@80 {
+		interrupts = <63 2 0 0>;
+	};
+
+	dma-channel@100 {
+		interrupts = <64 2 0 0>;
+	};
+
+	dma-channel@180 {
+		interrupts = <65 2 0 0>;
+	};
+};
+
+/include/ "pq3-usb2-dr-0.dtsi"
+usb@22000 {
+	compatible = "fsl-usb2-dr","fsl-usb2-dr-v2.2";
+	interrupts = <40 0x2 0 0>;
+};
+
+/include/ "pq3-esdhc-0.dtsi"
+	sdhc@2e000 {
+		fsl,sdhci-auto-cmd12;
+		interrupts = <41 0x2 0 0>;
+	};
+
+/include/ "pq3-sec4.4-0.dtsi"
+crypto@30000 {
+	interrupts	 = <57 2 0 0>;
+
+	sec_jr0: jr@1000 {
+		interrupts	 = <58 2 0 0>;
+	};
+
+	sec_jr1: jr@2000 {
+		interrupts	 = <59 2 0 0>;
+	};
+
+	sec_jr2: jr@3000 {
+		interrupts	 = <60 2 0 0>;
+	};
+
+	sec_jr3: jr@4000 {
+		interrupts	 = <61 2 0 0>;
+	};
+};
+
+/include/ "pq3-mpic.dtsi"
+/include/ "pq3-mpic-timer-B.dtsi"
+
+/include/ "pq3-etsec2-0.dtsi"
+enet0: ethernet@b0000 {
+	queue-group@b0000 {
+		fsl,rx-bit-map = <0xff>;
+		fsl,tx-bit-map = <0xff>;
+		interrupts = <26 2 0 0 27 2 0 0 28 2 0 0>;
+	};
+};
+
+/include/ "pq3-etsec2-1.dtsi"
+enet1: ethernet@b1000 {
+	queue-group@b1000 {
+		fsl,rx-bit-map = <0xff>;
+		fsl,tx-bit-map = <0xff>;
+		interrupts = <33 2 0 0 34 2 0 0 35 2 0 0>;
+	};
+};
+
+global-utilities@e0000 {
+		compatible = "fsl,bsc9132-guts";
+		reg = <0xe0000 0x1000>;
+		fsl,has-rstcr;
+	};
+};

arch/powerpc/boot/dts/fsl/bsc9132si-pre.dtsi

+/*
+ * BSC9132 Silicon/SoC Device Tree Source (pre include)
+ *
+ * Copyright 2014 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *       notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *       notice, this list of conditions and the following disclaimer in the
+ *       documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *       names of its contributors may be used to endorse or promote products
+ *       derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+
+/include/ "e500v2_power_isa.dtsi"
+
+/ {
+	#address-cells = <2>;
+	#size-cells = <2>;
+	interrupt-parent = <&mpic>;
+
+	aliases {
+		serial0 = &serial0;
+		ethernet0 = &enet0;
+		ethernet1 = &enet1;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: PowerPC,e500v2@0 {
+			device_type = "cpu";
+			reg = <0x0>;
+			next-level-cache = <&L2>;
+		};
+
+		cpu1: PowerPC,e500v2@1 {
+			device_type = "cpu";
+			reg = <0x1>;
+			next-level-cache = <&L2>;
+		};
+	};
+};

arch/powerpc/platforms/85xx/Kconfig

@@ -38,6 +38,15 @@ config C293_PCIE
 	  help
 	  This option enables support for the C293PCIE board
 
+config BSC9132_QDS
+	bool "Freescale BSC9132QDS"
+	select DEFAULT_UIMAGE
+	help
+	  This option enables support for the Freescale BSC9132 QDS board.
+	  BSC9132 is a heterogeneous SoC containing dual e500v2 powerpc cores
+	  and dual StarCore SC3850 DSP cores.
+	  Manufacturer : Freescale Semiconductor, Inc
+
 config MPC8540_ADS
 	bool "Freescale MPC8540 ADS"
 	select DEFAULT_UIMAGE

arch/powerpc/platforms/85xx/Makefile

@@ -6,6 +6,7 @@ obj-$(CONFIG_SMP) += smp.o
 obj-y += common.o
 
 obj-$(CONFIG_BSC9131_RDB) += bsc913x_rdb.o
+obj-$(CONFIG_BSC9132_QDS) += bsc913x_qds.o
 obj-$(CONFIG_C293_PCIE)   += c293pcie.o
 obj-$(CONFIG_MPC8540_ADS) += mpc85xx_ads.o
 obj-$(CONFIG_MPC8560_ADS) += mpc85xx_ads.o

arch/powerpc/platforms/85xx/bsc913x_qds.c

+/*
+ * BSC913xQDS Board Setup
+ *
+ * Author:
+ *   Harninder Rai <harninder.rai@freescale.com>
+ *   Priyanka Jain <Priyanka.Jain@freescale.com>
+ *
+ * Copyright 2014 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/of_platform.h>
+#include <linux/pci.h>
+#include <asm/mpic.h>
+#include <sysdev/fsl_soc.h>
+#include <asm/udbg.h>
+
+#include "mpc85xx.h"
+#include "smp.h"
+
+void __init bsc913x_qds_pic_init(void)
+{
+	struct mpic *mpic = mpic_alloc(NULL, 0, MPIC_BIG_ENDIAN |
+	  MPIC_SINGLE_DEST_CPU,
+	  0, 256, " OpenPIC  ");
+
+	if (!mpic)
+		pr_err("bsc913x: Failed to allocate MPIC structure\n");
+	else
+		mpic_init(mpic);
+}
+
+/*
+ * Setup the architecture
+ */
+static void __init bsc913x_qds_setup_arch(void)
+{
+	if (ppc_md.progress)
+		ppc_md.progress("bsc913x_qds_setup_arch()", 0);
+
+#if defined(CONFIG_SMP)
+	mpc85xx_smp_init();
+#endif
+
+	pr_info("bsc913x board from Freescale Semiconductor\n");
+}
+
+machine_device_initcall(bsc9132_qds, mpc85xx_common_publish_devices);
+
+/*
+ * Called very early, device-tree isn't unflattened
+ */
+
+static int __init bsc9132_qds_probe(void)
+{
+	unsigned long root = of_get_flat_dt_root();
+
+	return of_flat_dt_is_compatible(root, "fsl,bsc9132qds");
+}
+
+define_machine(bsc9132_qds) {
+	.name			= "BSC9132 QDS",
+	.probe			= bsc9132_qds_probe,
+	.setup_arch		= bsc913x_qds_setup_arch,
+	.init_IRQ		= bsc913x_qds_pic_init,
+	.get_irq		= mpic_get_irq,
+	.restart		= fsl_rstcr_restart,
+	.calibrate_decr		= generic_calibrate_decr,
+	.progress		= udbg_progress,
+};