ARM: dts: NSP: Add PCI support

Add PCI support to the Northstar Plus SoC.  This uses the existing
pcie-iproc driver.  So, all that is needed is device tree entries in the
DTS.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

arch/arm/boot/dts/bcm-nsp.dtsi

@@ -96,7 +96,7 @@ periph_clk: periph_clk {
 
 	axi {
 		compatible = "simple-bus";
-		ranges = <0x00000000 0x18000000 0x00001000>;
+		ranges = <0x00000000 0x18000000 0x00015000>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 
@@ -115,5 +115,77 @@ uart1: serial@18000400 {
 			clock-frequency = <62499840>;
 			status = "disabled";
 		};
+
+		pcie0: pcie@18012000 {
+			compatible = "brcm,iproc-pcie";
+			reg = <0x12000 0x1000>;
+
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0>;
+			interrupt-map = <0 0 0 0 &gic GIC_SPI 131 IRQ_TYPE_NONE>;
+
+			linux,pci-domain = <0>;
+
+			bus-range = <0x00 0xff>;
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+
+			/* Note: The HW does not support I/O resources.  So,
+			 * only the memory resource range is being specified.
+			 */
+			ranges = <0x82000000 0 0x08000000 0x08000000 0 0x8000000>;
+
+			status = "disabled";
+		};
+
+		pcie1: pcie@18013000 {
+			compatible = "brcm,iproc-pcie";
+			reg = <0x13000 0x1000>;
+
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0>;
+			interrupt-map = <0 0 0 0 &gic GIC_SPI 137 IRQ_TYPE_NONE>;
+
+			linux,pci-domain = <1>;
+
+			bus-range = <0x00 0xff>;
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+
+			/* Note: The HW does not support I/O resources.  So,
+			 * only the memory resource range is being specified.
+			 */
+			ranges = <0x82000000 0 0x40000000 0x40000000 0 0x8000000>;
+
+			status = "disabled";
+		};
+
+		pcie2: pcie@18014000 {
+			compatible = "brcm,iproc-pcie";
+			reg = <0x14000 0x1000>;
+
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0>;
+			interrupt-map = <0 0 0 0 &gic GIC_SPI 143 IRQ_TYPE_NONE>;
+
+			linux,pci-domain = <2>;
+
+			bus-range = <0x00 0xff>;
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+
+			/* Note: The HW does not support I/O resources.  So,
+			 * only the memory resource range is being specified.
+			 */
+			ranges = <0x82000000 0 0x48000000 0x48000000 0 0x8000000>;
+
+			status = "disabled";
+		};
 	};
 };

arch/arm/boot/dts/bcm958625k.dts

@@ -55,3 +55,15 @@ &uart0 {
 &uart1 {
 	status = "okay";
 };
+
+&pcie0 {
+	status = "okay";
+};
+
+&pcie1 {
+	status = "okay";
+};
+
+&pcie2 {
+	status = "okay";
+};