Merge branch 'ux500/devel' into next/devel

arch/arm/mach-ux500/board-mop500-sdi.c

@@ -131,6 +131,42 @@ void mop500_sdi_tc35892_init(void)
 	sdi0_configure();
 }
 
+/*
+ * SDI1 (SDIO WLAN)
+ */
+#ifdef CONFIG_STE_DMA40
+static struct stedma40_chan_cfg sdi1_dma_cfg_rx = {
+	.mode = STEDMA40_MODE_LOGICAL,
+	.dir = STEDMA40_PERIPH_TO_MEM,
+	.src_dev_type = DB8500_DMA_DEV32_SD_MM1_RX,
+	.dst_dev_type = STEDMA40_DEV_DST_MEMORY,
+	.src_info.data_width = STEDMA40_WORD_WIDTH,
+	.dst_info.data_width = STEDMA40_WORD_WIDTH,
+};
+
+static struct stedma40_chan_cfg sdi1_dma_cfg_tx = {
+	.mode = STEDMA40_MODE_LOGICAL,
+	.dir = STEDMA40_MEM_TO_PERIPH,
+	.src_dev_type = STEDMA40_DEV_SRC_MEMORY,
+	.dst_dev_type = DB8500_DMA_DEV32_SD_MM1_TX,
+	.src_info.data_width = STEDMA40_WORD_WIDTH,
+	.dst_info.data_width = STEDMA40_WORD_WIDTH,
+};
+#endif
+
+static struct mmci_platform_data mop500_sdi1_data = {
+	.ocr_mask	= MMC_VDD_29_30,
+	.f_max		= 50000000,
+	.capabilities	= MMC_CAP_4_BIT_DATA,
+	.gpio_cd	= -1,
+	.gpio_wp	= -1,
+#ifdef CONFIG_STE_DMA40
+	.dma_filter	= stedma40_filter,
+	.dma_rx_param	= &sdi1_dma_cfg_rx,
+	.dma_tx_param	= &sdi1_dma_cfg_tx,
+#endif
+};
+
 /*
  * SDI 2 (POP eMMC, not on DB8500ed)
  */
@@ -260,4 +296,6 @@ void __init hrefv60_sdi_init(void)
 	sdi0_en = HREFV60_SDMMC_EN_GPIO;
 	sdi0_vsel = HREFV60_SDMMC_1V8_3V_GPIO;
 	sdi0_configure();
+
+	db8500_add_sdi1(&mop500_sdi1_data, periphid);
 }

arch/arm/mach-ux500/board-mop500.c

@@ -672,7 +672,7 @@ static void __init hrefv60_init_machine(void)
 			ARRAY_SIZE(mop500_platform_devs));
 
 	mop500_i2c_init();
-	mop500_sdi_init();
+	hrefv60_sdi_init();
 	mop500_spi_init();
 	mop500_uart_init();
 

arch/arm/mach-ux500/board-mop500.h

@@ -7,40 +7,77 @@
 #ifndef __BOARD_MOP500_H
 #define __BOARD_MOP500_H
 
-/* snowball GPIO for MMC card */
-#define SNOWBALL_SDMMC_EN_GPIO 217
-#define SNOWBALL_SDMMC_1V8_3V_GPIO 228
-#define SNOWBALL_SDMMC_CD_GPIO 218
+/* Snowball specific GPIO assignments, this board has no GPIO expander */
+#define SNOWBALL_ACCEL_INT1_GPIO	163
+#define SNOWBALL_ACCEL_INT2_GPIO	164
+#define SNOWBALL_MAGNET_DRDY_GPIO	165
+#define SNOWBALL_SDMMC_EN_GPIO		217
+#define SNOWBALL_SDMMC_1V8_3V_GPIO	228
+#define SNOWBALL_SDMMC_CD_GPIO		218
 
 /* HREFv60-specific GPIO assignments, this board has no GPIO expander */
-#define HREFV60_TOUCH_RST_GPIO		143
-#define HREFV60_PROX_SENSE_GPIO		217
-#define HREFV60_HAL_SW_GPIO		145
-#define HREFV60_SDMMC_EN_GPIO		169
 #define HREFV60_SDMMC_1V8_3V_GPIO	5
-#define HREFV60_SDMMC_CD_GPIO		95
-#define HREFV60_ACCEL_INT1_GPIO		82
-#define HREFV60_ACCEL_INT2_GPIO		83
+#define HREFV60_CAMERA_FLASH_ENABLE	21
 #define HREFV60_MAGNET_DRDY_GPIO	32
 #define HREFV60_DISP1_RST_GPIO		65
 #define HREFV60_DISP2_RST_GPIO		66
+#define HREFV60_ACCEL_INT1_GPIO		82
+#define HREFV60_ACCEL_INT2_GPIO		83
+#define HREFV60_SDMMC_CD_GPIO		95
+#define HREFV60_XSHUTDOWN_SECONDARY_SENSOR 140
+#define HREFV60_TOUCH_RST_GPIO		143
+#define HREFV60_HAL_SW_GPIO		145
+#define HREFV60_SDMMC_EN_GPIO		169
+#define HREFV60_MMIO_XENON_CHARGE	170
+#define HREFV60_PROX_SENSE_GPIO		217
+
+/* MOP500 generic GPIOs */
+#define CAMERA_FLASH_INT_PIN		7
+#define CYPRESS_TOUCH_INT_PIN		84
+#define XSHUTDOWN_PRIMARY_SENSOR	141
+#define XSHUTDOWN_SECONDARY_SENSOR	142
+#define CYPRESS_TOUCH_RST_GPIO		143
+#define MOP500_HDMI_RST_GPIO		196
+#define CYPRESS_SLAVE_SELECT_GPIO	216
 
 /* GPIOs on the TC35892 expander */
 #define MOP500_EGPIO(x)			(NOMADIK_NR_GPIO + (x))
+#define GPIO_MAGNET_DRDY		MOP500_EGPIO(1)
 #define GPIO_SDMMC_CD			MOP500_EGPIO(3)
+#define GPIO_CAMERA_FLASH_ENABLE	MOP500_EGPIO(4)
+#define GPIO_MMIO_XENON_CHARGE		MOP500_EGPIO(5)
 #define GPIO_PROX_SENSOR		MOP500_EGPIO(7)
+#define GPIO_HAL_SENSOR			MOP500_EGPIO(8)
+#define GPIO_ACCEL_INT1			MOP500_EGPIO(10)
+#define GPIO_ACCEL_INT2			MOP500_EGPIO(11)
 #define GPIO_BU21013_CS			MOP500_EGPIO(13)
+#define MOP500_DISP2_RST_GPIO		MOP500_EGPIO(14)
+#define MOP500_DISP1_RST_GPIO		MOP500_EGPIO(15)
 #define GPIO_SDMMC_EN			MOP500_EGPIO(17)
 #define GPIO_SDMMC_1V8_3V_SEL		MOP500_EGPIO(18)
 #define MOP500_EGPIO_END		MOP500_EGPIO(24)
 
-/* GPIOs on the AB8500 mixed-signals circuit */
-#define MOP500_AB8500_GPIO(x)		(MOP500_EGPIO_END + (x))
+/*
+ * GPIOs on the AB8500 mixed-signals circuit
+ * Notice that we subtract 1 from the number passed into the macro, this is
+ * because the AB8500 GPIO pins are enumbered starting from 1, so the value in
+ * parens matches the GPIO pin number in the data sheet.
+ */
+#define MOP500_AB8500_GPIO(x)		(MOP500_EGPIO_END + (x) - 1)
+/*Snowball AB8500 GPIO */
+#define SNOWBALL_VSMPS2_1V8_GPIO	MOP500_AB8500_PIN_GPIO(1)	/* SYSCLKREQ2/GPIO1 */
+#define SNOWBALL_PM_GPIO1_GPIO		MOP500_AB8500_PIN_GPIO(2)	/* SYSCLKREQ3/GPIO2 */
+#define SNOWBALL_WLAN_CLK_REQ_GPIO	MOP500_AB8500_PIN_GPIO(3)	/* SYSCLKREQ4/GPIO3 */
+#define SNOWBALL_PM_GPIO4_GPIO		MOP500_AB8500_PIN_GPIO(4)	/* SYSCLKREQ6/GPIO4 */
+#define SNOWBALL_EN_3V6_GPIO		MOP500_AB8500_PIN_GPIO(16)	/* PWMOUT3/GPIO16 */
+#define SNOWBALL_PME_ETH_GPIO		MOP500_AB8500_PIN_GPIO(24)	/* SYSCLKREQ7/GPIO24 */
+#define SNOWBALL_EN_3V3_ETH_GPIO	MOP500_AB8500_PIN_GPIO(26)	/* GPIO26 */
 
 struct i2c_board_info;
 
 extern void mop500_sdi_init(void);
 extern void snowball_sdi_init(void);
+extern void hrefv60_sdi_init(void);
 extern void mop500_sdi_tc35892_init(void);
 void __init mop500_u8500uib_init(void);
 void __init mop500_stuib_init(void);