mrst_max3110: add UART driver for Max3110 on Moorestown

This driver enable the max3110 device, it can be used as
a system console. the IRQ needs be enabled if user want a
better performance. MRST max3110 works in 3.684MHz clock,
which supports 230400 as its maximum rate.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

drivers/serial/Kconfig

@@ -690,6 +690,23 @@ config SERIAL_SA1100_CONSOLE
 	  your boot loader (lilo or loadlin) about how to pass options to the
 	  kernel at boot time.)
 
+config SERIAL_MRST_MAX3110
+	tristate "SPI UART driver for Max3110"
+	depends on SPI_DW_PCI
+	select SERIAL_CORE
+	select SERIAL_CORE_CONSOLE
+	help
+	  This is the UART protocol driver for the MAX3110 device on
+	  the Intel Moorestown platform. On other systems use the max3100
+	  driver.
+
+config MRST_MAX3110_IRQ
+	boolean "Enable GPIO IRQ for Max3110 over Moorestown"
+	default n
+	depends on SERIAL_MRST_MAX3110 && GPIO_LANGWELL
+	help
+	  This has to be enabled after Moorestown GPIO driver is loaded
+
 config SERIAL_BFIN
 	tristate "Blackfin serial port support"
 	depends on BLACKFIN

drivers/serial/Makefile

@@ -84,3 +84,4 @@ obj-$(CONFIG_SERIAL_TIMBERDALE)	+= timbuart.o
 obj-$(CONFIG_SERIAL_GRLIB_GAISLER_APBUART) += apbuart.o
 obj-$(CONFIG_SERIAL_ALTERA_JTAGUART) += altera_jtaguart.o
 obj-$(CONFIG_SERIAL_ALTERA_UART) += altera_uart.o
+obj-$(CONFIG_SERIAL_MRST_MAX3110)	+= mrst_max3110.o

drivers/serial/mrst_max3110.h

+#ifndef _MRST_MAX3110_H
+#define _MRST_MAX3110_H
+
+#define MAX3110_HIGH_CLK	0x1	/* 3.6864 MHZ */
+#define MAX3110_LOW_CLK		0x0	/* 1.8432 MHZ */
+
+/* status bits for all 4 MAX3110 operate modes */
+#define MAX3110_READ_DATA_AVAILABLE	(1 << 15)
+#define MAX3110_WRITE_BUF_EMPTY		(1 << 14)
+
+#define WC_TAG			(3 << 14)
+#define RC_TAG			(1 << 14)
+#define WD_TAG			(2 << 14)
+#define RD_TAG			(0 << 14)
+
+/* bits def for write configuration */
+#define WC_FIFO_ENABLE_MASK	(1 << 13)
+#define WC_FIFO_ENABLE		(0 << 13)
+
+#define WC_SW_SHDI		(1 << 12)
+
+#define WC_IRQ_MASK		(0xF << 8)
+#define WC_TXE_IRQ_ENABLE	(1 << 11)	/* TX empty irq */
+#define WC_RXA_IRQ_ENABLE	(1 << 10)	/* RX availabe irq */
+#define WC_PAR_HIGH_IRQ_ENABLE	(1 << 9)
+#define WC_REC_ACT_IRQ_ENABLE	(1 << 8)
+
+#define WC_IRDA_ENABLE		(1 << 7)
+
+#define WC_STOPBITS_MASK	(1 << 6)
+#define WC_2_STOPBITS		(1 << 6)
+#define WC_1_STOPBITS		(0 << 6)
+
+#define WC_PARITY_ENABLE_MASK	(1 << 5)
+#define WC_PARITY_ENABLE	(1 << 5)
+
+#define WC_WORDLEN_MASK		(1 << 4)
+#define WC_7BIT_WORD		(1 << 4)
+#define WC_8BIT_WORD		(0 << 4)
+
+#define WC_BAUD_DIV_MASK	(0xF)
+#define WC_BAUD_DR1		(0x0)
+#define WC_BAUD_DR2		(0x1)
+#define WC_BAUD_DR4		(0x2)
+#define WC_BAUD_DR8		(0x3)
+#define WC_BAUD_DR16		(0x4)
+#define WC_BAUD_DR32		(0x5)
+#define WC_BAUD_DR64		(0x6)
+#define WC_BAUD_DR128		(0x7)
+#define WC_BAUD_DR3		(0x8)
+#define WC_BAUD_DR6		(0x9)
+#define WC_BAUD_DR12		(0xA)
+#define WC_BAUD_DR24		(0xB)
+#define WC_BAUD_DR48		(0xC)
+#define WC_BAUD_DR96		(0xD)
+#define WC_BAUD_DR192		(0xE)
+#define WC_BAUD_DR384		(0xF)
+
+#endif