xtensa: Added Cadence CSP kernel configuration for Xtensa

Added defconfig, device tree and Xtensa variant header files for the
Cadence Configurable System Platform "xt_lnx" processor configuration.
Signed-off-by: Scott Telford <stelford@cadence.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>

arch/xtensa/boot/dts/csp.dts

+/dts-v1/;
+
+/ {
+	compatible = "cdns,xtensa-xtfpga";
+	#address-cells = <1>;
+	#size-cells = <1>;
+	interrupt-parent = <&pic>;
+
+	chosen {
+		bootargs = "earlycon=cdns,0xfd000000,115200 console=tty0 console=ttyPS0,115200 root=/dev/ram0 rw earlyprintk loglevel=8 nohz=off ignore_loglevel";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x40000000>;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		cpu@0 {
+			compatible = "cdns,xtensa-cpu";
+			reg = <0>;
+		};
+	};
+
+	pic: pic {
+		compatible = "cdns,xtensa-pic";
+		#interrupt-cells = <2>;
+		interrupt-controller;
+	};
+
+	clocks {
+		osc: main-oscillator {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+		};
+	};
+
+	soc {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "simple-bus";
+		ranges = <0x00000000 0xf0000000 0x10000000>;
+
+		uart0: serial@0d000000 {
+			compatible = "xlnx,xuartps", "cdns,uart-r1p8";
+			clocks = <&osc>, <&osc>;
+			clock-names = "uart_clk", "pclk";
+			reg = <0x0d000000 0x1000>;
+			interrupts = <0 1>;
+		};
+	};
+};

arch/xtensa/configs/cadence_csp_defconfig

+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_USELIB=y
+CONFIG_IRQ_DOMAIN_DEBUG=y
+CONFIG_NO_HZ_IDLE=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_IRQ_TIME_ACCOUNTING=y
+CONFIG_BSD_PROCESS_ACCT=y
+CONFIG_CGROUP_FREEZER=y
+CONFIG_CPUSETS=y
+CONFIG_CGROUP_DEVICE=y
+CONFIG_CGROUP_CPUACCT=y
+CONFIG_CGROUP_DEBUG=y
+CONFIG_NAMESPACES=y
+CONFIG_SCHED_AUTOGROUP=y
+CONFIG_RELAY=y
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_INITRAMFS_SOURCE="$$KERNEL_INITRAMFS_SOURCE"
+# CONFIG_RD_BZIP2 is not set
+# CONFIG_RD_LZMA is not set
+# CONFIG_RD_XZ is not set
+# CONFIG_RD_LZO is not set
+# CONFIG_RD_LZ4 is not set
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_EMBEDDED=y
+CONFIG_PROFILING=y
+CONFIG_MODULES=y
+CONFIG_MODULE_FORCE_LOAD=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_FORCE_UNLOAD=y
+# CONFIG_IOSCHED_DEADLINE is not set
+# CONFIG_IOSCHED_CFQ is not set
+CONFIG_XTENSA_VARIANT_CUSTOM=y
+CONFIG_XTENSA_VARIANT_CUSTOM_NAME="csp"
+CONFIG_XTENSA_UNALIGNED_USER=y
+CONFIG_PREEMPT=y
+CONFIG_HIGHMEM=y
+# CONFIG_PCI is not set
+CONFIG_XTENSA_PLATFORM_XTFPGA=y
+CONFIG_USE_OF=y
+CONFIG_BUILTIN_DTB="csp"
+# CONFIG_COMPACTION is not set
+CONFIG_XTFPGA_LCD=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_IP_PNP_RARP=y
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_DIAG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_WIRELESS is not set
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+# CONFIG_STANDALONE is not set
+# CONFIG_FW_LOADER is not set
+CONFIG_MTD=y
+CONFIG_MTD_CFI=y
+CONFIG_MTD_JEDECPROBE=y
+CONFIG_MTD_CFI_INTELEXT=y
+CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_CFI_STAA=y
+CONFIG_MTD_PHYSMAP_OF=y
+CONFIG_MTD_UBI=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_RAM=y
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
+# CONFIG_INPUT_MOUSEDEV is not set
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+CONFIG_LEGACY_PTY_COUNT=16
+CONFIG_SERIAL_XILINX_PS_UART=y
+CONFIG_SERIAL_XILINX_PS_UART_CONSOLE=y
+CONFIG_HW_RANDOM=y
+# CONFIG_HWMON is not set
+CONFIG_WATCHDOG=y
+CONFIG_WATCHDOG_NOWAYOUT=y
+CONFIG_SOFT_WATCHDOG=y
+# CONFIG_VGA_CONSOLE is not set
+# CONFIG_USB_SUPPORT is not set
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_EXT3_FS=y
+CONFIG_FANOTIFY=y
+CONFIG_VFAT_FS=y
+CONFIG_PROC_KCORE=y
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
+# CONFIG_MISC_FILESYSTEMS is not set
+CONFIG_NFS_FS=y
+CONFIG_NFS_V4=y
+CONFIG_NFS_SWAP=y
+CONFIG_ROOT_NFS=y
+CONFIG_SUNRPC_DEBUG=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_PRINTK_TIME=y
+CONFIG_DYNAMIC_DEBUG=y
+CONFIG_DEBUG_INFO=y
+CONFIG_MAGIC_SYSRQ=y
+CONFIG_LOCKUP_DETECTOR=y
+# CONFIG_SCHED_DEBUG is not set
+CONFIG_SCHEDSTATS=y
+CONFIG_TIMER_STATS=y
+CONFIG_DEBUG_RT_MUTEXES=y
+CONFIG_PROVE_LOCKING=y
+CONFIG_DEBUG_ATOMIC_SLEEP=y
+CONFIG_RCU_TRACE=y
+CONFIG_FUNCTION_TRACER=y
+# CONFIG_S32C1I_SELFTEST is not set
+# CONFIG_CRYPTO_ECHAINIV is not set
+CONFIG_CRYPTO_DEFLATE=y
+CONFIG_CRYPTO_LZO=y
+# CONFIG_CRYPTO_HW is not set

arch/xtensa/variants/csp/include/variant/tie-asm.h

+/* 
+ * tie-asm.h -- compile-time HAL assembler definitions dependent on CORE & TIE
+ *
+ *  NOTE:  This header file is not meant to be included directly.
+ */
+
+/* This header file contains assembly-language definitions (assembly
+   macros, etc.) for this specific Xtensa processor's TIE extensions
+   and options.  It is customized to this Xtensa processor configuration.
+
+   Copyright (c) 1999-2015 Cadence Design Systems Inc.
+
+   Permission is hereby granted, free of charge, to any person obtaining
+   a copy of this software and associated documentation files (the
+   "Software"), to deal in the Software without restriction, including
+   without limitation the rights to use, copy, modify, merge, publish,
+   distribute, sublicense, and/or sell copies of the Software, and to
+   permit persons to whom the Software is furnished to do so, subject to
+   the following conditions:
+
+   The above copyright notice and this permission notice shall be included
+   in all copies or substantial portions of the Software.
+
+   THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+   EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
+   MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.
+   IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY
+   CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT,
+   TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE
+   SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.  */
+
+#ifndef _XTENSA_CORE_TIE_ASM_H
+#define _XTENSA_CORE_TIE_ASM_H
+
+/*  Selection parameter values for save-area save/restore macros:  */
+/*  Option vs. TIE:  */
+#define XTHAL_SAS_TIE	0x0001	/* custom extension or coprocessor */
+#define XTHAL_SAS_OPT	0x0002	/* optional (and not a coprocessor) */
+#define XTHAL_SAS_ANYOT	0x0003	/* both of the above */
+/*  Whether used automatically by compiler:  */
+#define XTHAL_SAS_NOCC	0x0004	/* not used by compiler w/o special opts/code */
+#define XTHAL_SAS_CC	0x0008	/* used by compiler without special opts/code */
+#define XTHAL_SAS_ANYCC	0x000C	/* both of the above */
+/*  ABI handling across function calls:  */
+#define XTHAL_SAS_CALR	0x0010	/* caller-saved */
+#define XTHAL_SAS_CALE	0x0020	/* callee-saved */
+#define XTHAL_SAS_GLOB	0x0040	/* global across function calls (in thread) */
+#define XTHAL_SAS_ANYABI	0x0070	/* all of the above three */
+/*  Misc  */
+#define XTHAL_SAS_ALL	0xFFFF	/* include all default NCP contents */
+#define XTHAL_SAS3(optie,ccuse,abi)	( ((optie) & XTHAL_SAS_ANYOT)  \
+					| ((ccuse) & XTHAL_SAS_ANYCC)  \
+					| ((abi)   & XTHAL_SAS_ANYABI) )
+
+
+    /*
+      *  Macro to store all non-coprocessor (extra) custom TIE and optional state
+      *  (not including zero-overhead loop registers).
+      *  Required parameters:
+      *      ptr         Save area pointer address register (clobbered)
+      *                  (register must contain a 4 byte aligned address).
+      *      at1..at4    Four temporary address registers (first XCHAL_NCP_NUM_ATMPS
+      *                  registers are clobbered, the remaining are unused).
+      *  Optional parameters:
+      *      continue    If macro invoked as part of a larger store sequence, set to 1
+      *                  if this is not the first in the sequence.  Defaults to 0.
+      *      ofs         Offset from start of larger sequence (from value of first ptr
+      *                  in sequence) at which to store.  Defaults to next available space
+      *                  (or 0 if <continue> is 0).
+      *      select      Select what category(ies) of registers to store, as a bitmask
+      *                  (see XTHAL_SAS_xxx constants).  Defaults to all registers.
+      *      alloc       Select what category(ies) of registers to allocate; if any
+      *                  category is selected here that is not in <select>, space for
+      *                  the corresponding registers is skipped without doing any store.
+      */
+    .macro xchal_ncp_store  ptr at1 at2 at3 at4  continue=0 ofs=-1 select=XTHAL_SAS_ALL alloc=0
+	xchal_sa_start	\continue, \ofs
+	// Optional global registers used by default by the compiler:
+	.ifeq (XTHAL_SAS_OPT | XTHAL_SAS_CC | XTHAL_SAS_GLOB) & ~(\select)
+	xchal_sa_align	\ptr, 0, 1020, 4, 4
+	rur.THREADPTR	\at1		// threadptr option
+	s32i	\at1, \ptr, .Lxchal_ofs_+0
+	.set	.Lxchal_ofs_, .Lxchal_ofs_ + 4
+	.elseif ((XTHAL_SAS_OPT | XTHAL_SAS_CC | XTHAL_SAS_GLOB) & ~(\alloc)) == 0
+	xchal_sa_align	\ptr, 0, 1020, 4, 4
+	.set	.Lxchal_ofs_, .Lxchal_ofs_ + 4
+	.endif
+	// Optional caller-saved registers used by default by the compiler:
+	.ifeq (XTHAL_SAS_OPT | XTHAL_SAS_CC | XTHAL_SAS_CALR) & ~(\select)
+	xchal_sa_align	\ptr, 0, 1016, 4, 4
+	rsr.ACCLO	\at1		// MAC16 option
+	s32i	\at1, \ptr, .Lxchal_ofs_+0
+	rsr.ACCHI	\at1		// MAC16 option
+	s32i	\at1, \ptr, .Lxchal_ofs_+4
+	.set	.Lxchal_ofs_, .Lxchal_ofs_ + 8
+	.elseif ((XTHAL_SAS_OPT | XTHAL_SAS_CC | XTHAL_SAS_CALR) & ~(\alloc)) == 0
+	xchal_sa_align	\ptr, 0, 1016, 4, 4
+	.set	.Lxchal_ofs_, .Lxchal_ofs_ + 8
+	.endif
+	// Optional caller-saved registers not used by default by the compiler:
+	.ifeq (XTHAL_SAS_OPT | XTHAL_SAS_NOCC | XTHAL_SAS_CALR) & ~(\select)
+	xchal_sa_align	\ptr, 0, 1000, 4, 4
+	rsr.BR	\at1		// boolean option
+	s32i	\at1, \ptr, .Lxchal_ofs_+0
+	rsr.SCOMPARE1	\at1		// conditional store option
+	s32i	\at1, \ptr, .Lxchal_ofs_+4
+	rsr.M0	\at1		// MAC16 option
+	s32i	\at1, \ptr, .Lxchal_ofs_+8
+	rsr.M1	\at1		// MAC16 option
+	s32i	\at1, \ptr, .Lxchal_ofs_+12
+	rsr.M2	\at1		// MAC16 option
+	s32i	\at1, \ptr, .Lxchal_ofs_+16
+	rsr.M3	\at1		// MAC16 option
+	s32i	\at1, \ptr, .Lxchal_ofs_+20
+	.set	.Lxchal_ofs_, .Lxchal_ofs_ + 24
+	.elseif ((XTHAL_SAS_OPT | XTHAL_SAS_NOCC | XTHAL_SAS_CALR) & ~(\alloc)) == 0
+	xchal_sa_align	\ptr, 0, 1000, 4, 4
+	.set	.Lxchal_ofs_, .Lxchal_ofs_ + 24
+	.endif
+    .endm	// xchal_ncp_store
+
+    /*
+      *  Macro to load all non-coprocessor (extra) custom TIE and optional state
+      *  (not including zero-overhead loop registers).
+      *  Required parameters:
+      *      ptr         Save area pointer address register (clobbered)
+      *                  (register must contain a 4 byte aligned address).
+      *      at1..at4    Four temporary address registers (first XCHAL_NCP_NUM_ATMPS
+      *                  registers are clobbered, the remaining are unused).
+      *  Optional parameters:
+      *      continue    If macro invoked as part of a larger load sequence, set to 1
+      *                  if this is not the first in the sequence.  Defaults to 0.
+      *      ofs         Offset from start of larger sequence (from value of first ptr
+      *                  in sequence) at which to load.  Defaults to next available space
+      *                  (or 0 if <continue> is 0).
+      *      select      Select what category(ies) of registers to load, as a bitmask
+      *                  (see XTHAL_SAS_xxx constants).  Defaults to all registers.
+      *      alloc       Select what category(ies) of registers to allocate; if any
+      *                  category is selected here that is not in <select>, space for
+      *                  the corresponding registers is skipped without doing any load.
+      */
+    .macro xchal_ncp_load  ptr at1 at2 at3 at4  continue=0 ofs=-1 select=XTHAL_SAS_ALL alloc=0
+	xchal_sa_start	\continue, \ofs
+	// Optional global registers used by default by the compiler:
+	.ifeq (XTHAL_SAS_OPT | XTHAL_SAS_CC | XTHAL_SAS_GLOB) & ~(\select)
+	xchal_sa_align	\ptr, 0, 1020, 4, 4
+	l32i	\at1, \ptr, .Lxchal_ofs_+0
+	wur.THREADPTR	\at1		// threadptr option
+	.set	.Lxchal_ofs_, .Lxchal_ofs_ + 4
+	.elseif ((XTHAL_SAS_OPT | XTHAL_SAS_CC | XTHAL_SAS_GLOB) & ~(\alloc)) == 0
+	xchal_sa_align	\ptr, 0, 1020, 4, 4
+	.set	.Lxchal_ofs_, .Lxchal_ofs_ + 4
+	.endif
+	// Optional caller-saved registers used by default by the compiler:
+	.ifeq (XTHAL_SAS_OPT | XTHAL_SAS_CC | XTHAL_SAS_CALR) & ~(\select)
+	xchal_sa_align	\ptr, 0, 1016, 4, 4
+	l32i	\at1, \ptr, .Lxchal_ofs_+0
+	wsr.ACCLO	\at1		// MAC16 option
+	l32i	\at1, \ptr, .Lxchal_ofs_+4
+	wsr.ACCHI	\at1		// MAC16 option
+	.set	.Lxchal_ofs_, .Lxchal_ofs_ + 8
+	.elseif ((XTHAL_SAS_OPT | XTHAL_SAS_CC | XTHAL_SAS_CALR) & ~(\alloc)) == 0
+	xchal_sa_align	\ptr, 0, 1016, 4, 4
+	.set	.Lxchal_ofs_, .Lxchal_ofs_ + 8
+	.endif
+	// Optional caller-saved registers not used by default by the compiler:
+	.ifeq (XTHAL_SAS_OPT | XTHAL_SAS_NOCC | XTHAL_SAS_CALR) & ~(\select)
+	xchal_sa_align	\ptr, 0, 1000, 4, 4
+	l32i	\at1, \ptr, .Lxchal_ofs_+0
+	wsr.BR	\at1		// boolean option
+	l32i	\at1, \ptr, .Lxchal_ofs_+4
+	wsr.SCOMPARE1	\at1		// conditional store option
+	l32i	\at1, \ptr, .Lxchal_ofs_+8
+	wsr.M0	\at1		// MAC16 option
+	l32i	\at1, \ptr, .Lxchal_ofs_+12
+	wsr.M1	\at1		// MAC16 option
+	l32i	\at1, \ptr, .Lxchal_ofs_+16
+	wsr.M2	\at1		// MAC16 option
+	l32i	\at1, \ptr, .Lxchal_ofs_+20
+	wsr.M3	\at1		// MAC16 option
+	.set	.Lxchal_ofs_, .Lxchal_ofs_ + 24
+	.elseif ((XTHAL_SAS_OPT | XTHAL_SAS_NOCC | XTHAL_SAS_CALR) & ~(\alloc)) == 0
+	xchal_sa_align	\ptr, 0, 1000, 4, 4
+	.set	.Lxchal_ofs_, .Lxchal_ofs_ + 24
+	.endif
+    .endm	// xchal_ncp_load
+
+
+#define XCHAL_NCP_NUM_ATMPS	1
+
+#define XCHAL_SA_NUM_ATMPS	1
+
+#endif /*_XTENSA_CORE_TIE_ASM_H*/
+

arch/xtensa/variants/csp/include/variant/tie.h

+/* 
+ * tie.h -- compile-time HAL definitions dependent on CORE & TIE configuration
+ *
+ *  NOTE:  This header file is not meant to be included directly.
+ */
+
+/* This header file describes this specific Xtensa processor's TIE extensions
+   that extend basic Xtensa core functionality.  It is customized to this
+   Xtensa processor configuration.
+
+   Copyright (c) 1999-2015 Cadence Design Systems Inc.
+
+   Permission is hereby granted, free of charge, to any person obtaining
+   a copy of this software and associated documentation files (the
+   "Software"), to deal in the Software without restriction, including
+   without limitation the rights to use, copy, modify, merge, publish,
+   distribute, sublicense, and/or sell copies of the Software, and to
+   permit persons to whom the Software is furnished to do so, subject to
+   the following conditions:
+
+   The above copyright notice and this permission notice shall be included
+   in all copies or substantial portions of the Software.
+
+   THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+   EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
+   MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.
+   IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY
+   CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT,
+   TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE
+   SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.  */
+
+#ifndef _XTENSA_CORE_TIE_H
+#define _XTENSA_CORE_TIE_H
+
+#define XCHAL_CP_NUM			1	/* number of coprocessors */
+#define XCHAL_CP_MAX			8	/* max CP ID + 1 (0 if none) */
+#define XCHAL_CP_MASK			0x80	/* bitmask of all CPs by ID */
+#define XCHAL_CP_PORT_MASK		0x80	/* bitmask of only port CPs */
+
+/*  Basic parameters of each coprocessor:  */
+#define XCHAL_CP7_NAME			"XTIOP"
+#define XCHAL_CP7_IDENT			XTIOP
+#define XCHAL_CP7_SA_SIZE		0	/* size of state save area */
+#define XCHAL_CP7_SA_ALIGN		1	/* min alignment of save area */
+#define XCHAL_CP_ID_XTIOP           	7	/* coprocessor ID (0..7) */
+
+/*  Filler info for unassigned coprocessors, to simplify arrays etc:  */
+#define XCHAL_CP0_SA_SIZE		0
+#define XCHAL_CP0_SA_ALIGN		1
+#define XCHAL_CP1_SA_SIZE		0
+#define XCHAL_CP1_SA_ALIGN		1
+#define XCHAL_CP2_SA_SIZE		0
+#define XCHAL_CP2_SA_ALIGN		1
+#define XCHAL_CP3_SA_SIZE		0
+#define XCHAL_CP3_SA_ALIGN		1
+#define XCHAL_CP4_SA_SIZE		0
+#define XCHAL_CP4_SA_ALIGN		1
+#define XCHAL_CP5_SA_SIZE		0
+#define XCHAL_CP5_SA_ALIGN		1
+#define XCHAL_CP6_SA_SIZE		0
+#define XCHAL_CP6_SA_ALIGN		1
+
+/*  Save area for non-coprocessor optional and custom (TIE) state:  */
+#define XCHAL_NCP_SA_SIZE		36
+#define XCHAL_NCP_SA_ALIGN		4
+
+/*  Total save area for optional and custom state (NCP + CPn):  */
+#define XCHAL_TOTAL_SA_SIZE		48	/* with 16-byte align padding */
+#define XCHAL_TOTAL_SA_ALIGN		4	/* actual minimum alignment */
+
+/*
+ * Detailed contents of save areas.
+ * NOTE:  caller must define the XCHAL_SA_REG macro (not defined here)
+ * before expanding the XCHAL_xxx_SA_LIST() macros.
+ *
+ * XCHAL_SA_REG(s,ccused,abikind,kind,opt,name,galign,align,asize,
+ *		dbnum,base,regnum,bitsz,gapsz,reset,x...)
+ *
+ *	s = passed from XCHAL_*_LIST(s), eg. to select how to expand
+ *	ccused = set if used by compiler without special options or code
+ *	abikind = 0 (caller-saved), 1 (callee-saved), or 2 (thread-global)
+ *	kind = 0 (special reg), 1 (TIE user reg), or 2 (TIE regfile reg)
+ *	opt = 0 (custom TIE extension or coprocessor), or 1 (optional reg)
+ *	name = lowercase reg name (no quotes)
+ *	galign = group byte alignment (power of 2) (galign >= align)
+ *	align = register byte alignment (power of 2)
+ *	asize = allocated size in bytes (asize*8 == bitsz + gapsz + padsz)
+ *	  (not including any pad bytes required to galign this or next reg)
+ *	dbnum = unique target number f/debug (see <xtensa-libdb-macros.h>)
+ *	base = reg shortname w/o index (or sr=special, ur=TIE user reg)
+ *	regnum = reg index in regfile, or special/TIE-user reg number
+ *	bitsz = number of significant bits (regfile width, or ur/sr mask bits)
+ *	gapsz = intervening bits, if bitsz bits not stored contiguously
+ *	(padsz = pad bits at end [TIE regfile] or at msbits [ur,sr] of asize)
+ *	reset = register reset value (or 0 if undefined at reset)
+ *	x = reserved for future use (0 until then)
+ *
+ *  To filter out certain registers, e.g. to expand only the non-global
+ *  registers used by the compiler, you can do something like this:
+ *
+ *  #define XCHAL_SA_REG(s,ccused,p...)	SELCC##ccused(p)
+ *  #define SELCC0(p...)
+ *  #define SELCC1(abikind,p...)	SELAK##abikind(p)
+ *  #define SELAK0(p...)		REG(p)
+ *  #define SELAK1(p...)		REG(p)
+ *  #define SELAK2(p...)
+ *  #define REG(kind,tie,name,galn,aln,asz,csz,dbnum,base,rnum,bsz,rst,x...) \
+ *		...what you want to expand...
+ */
+
+#define XCHAL_NCP_SA_NUM	9
+#define XCHAL_NCP_SA_LIST(s)	\
+ XCHAL_SA_REG(s,1,2,1,1,      threadptr, 4, 4, 4,0x03E7,  ur,231, 32,0,0,0) \
+ XCHAL_SA_REG(s,1,0,0,1,          acclo, 4, 4, 4,0x0210,  sr,16 , 32,0,0,0) \
+ XCHAL_SA_REG(s,1,0,0,1,          acchi, 4, 4, 4,0x0211,  sr,17 ,  8,0,0,0) \
+ XCHAL_SA_REG(s,0,0,0,1,             br, 4, 4, 4,0x0204,  sr,4  , 16,0,0,0) \
+ XCHAL_SA_REG(s,0,0,0,1,      scompare1, 4, 4, 4,0x020C,  sr,12 , 32,0,0,0) \
+ XCHAL_SA_REG(s,0,0,0,1,             m0, 4, 4, 4,0x0220,  sr,32 , 32,0,0,0) \
+ XCHAL_SA_REG(s,0,0,0,1,             m1, 4, 4, 4,0x0221,  sr,33 , 32,0,0,0) \
+ XCHAL_SA_REG(s,0,0,0,1,             m2, 4, 4, 4,0x0222,  sr,34 , 32,0,0,0) \
+ XCHAL_SA_REG(s,0,0,0,1,             m3, 4, 4, 4,0x0223,  sr,35 , 32,0,0,0)
+
+#define XCHAL_CP0_SA_NUM	0
+#define XCHAL_CP0_SA_LIST(s)	/* empty */
+
+#define XCHAL_CP1_SA_NUM	0
+#define XCHAL_CP1_SA_LIST(s)	/* empty */
+
+#define XCHAL_CP2_SA_NUM	0
+#define XCHAL_CP2_SA_LIST(s)	/* empty */
+
+#define XCHAL_CP3_SA_NUM	0
+#define XCHAL_CP3_SA_LIST(s)	/* empty */
+
+#define XCHAL_CP4_SA_NUM	0
+#define XCHAL_CP4_SA_LIST(s)	/* empty */
+
+#define XCHAL_CP5_SA_NUM	0
+#define XCHAL_CP5_SA_LIST(s)	/* empty */
+
+#define XCHAL_CP6_SA_NUM	0
+#define XCHAL_CP6_SA_LIST(s)	/* empty */
+
+#define XCHAL_CP7_SA_NUM	0
+#define XCHAL_CP7_SA_LIST(s)	/* empty */
+
+/* Byte length of instruction from its first nibble (op0 field), per FLIX.  */
+#define XCHAL_OP0_FORMAT_LENGTHS	3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3
+/* Byte length of instruction from its first byte, per FLIX.  */
+#define XCHAL_BYTE0_FORMAT_LENGTHS	\
+	3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3, 3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3,\
+	3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3, 3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3,\
+	3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3, 3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3,\
+	3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3, 3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3,\
+	3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3, 3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3,\
+	3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3, 3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3,\
+	3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3, 3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3,\
+	3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3, 3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3
+
+#endif /*_XTENSA_CORE_TIE_H*/
+