staging/rtl8192u: use same indent for switch and case

Fix the checkpatch error "switch and case should be at the same indent"
Signed-off-by: Sebastian Hahn <snsehahn@cip.cs.fau.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/staging/rtl8192u/ieee80211/ieee80211_tx.c

@@ -283,22 +283,22 @@ ieee80211_classify(struct sk_buff *skb, struct ieee80211_network *network)
 //	IEEE80211_DEBUG_DATA(IEEE80211_DL_DATA, skb->data, skb->len);
 	ip = ip_hdr(skb);
 	switch (ip->tos & 0xfc) {
-		case 0x20:
-			return 2;
-		case 0x40:
-			return 1;
-		case 0x60:
-			return 3;
-		case 0x80:
-			return 4;
-		case 0xa0:
-			return 5;
-		case 0xc0:
-			return 6;
-		case 0xe0:
-			return 7;
-		default:
-			return 0;
+	case 0x20:
+		return 2;
+	case 0x40:
+		return 1;
+	case 0x60:
+		return 3;
+	case 0x80:
+		return 4;
+	case 0xa0:
+		return 5;
+	case 0xc0:
+		return 6;
+	case 0xe0:
+		return 7;
+	default:
+		return 0;
 	}
 }
 

drivers/staging/rtl8192u/ieee80211/ieee80211_wx.c

@@ -761,7 +761,7 @@ int ieee80211_wx_set_mlme(struct ieee80211_device *ieee,
 	case IW_MLME_DISASSOC:
 		ieee80211_disassociate(ieee);
 		break;
-	 default:
+	default:
 		return -EOPNOTSUPP;
 	}
 	return 0;

drivers/staging/rtl8192u/r8192U_wx.c

@@ -710,12 +710,12 @@ static int r8192_wx_set_enc(struct net_device *dev,
 		#define CONF_WEP104 0x14
 
 		switch(wrqu->encoding.flags & IW_ENCODE_INDEX){
-			case 0: key_idx = ieee->tx_keyidx; break;
-			case 1:	key_idx = 0; break;
-			case 2:	key_idx = 1; break;
-			case 3:	key_idx = 2; break;
-			case 4:	key_idx	= 3; break;
-			default: break;
+		case 0: key_idx = ieee->tx_keyidx; break;
+		case 1:	key_idx = 0; break;
+		case 2:	key_idx = 1; break;
+		case 3:	key_idx = 2; break;
+		case 4:	key_idx	= 3; break;
+		default: break;
 		}
 
 		if(wrqu->encoding.length==0x5){

drivers/staging/rtl8192u/r819xU_firmware.c

@@ -334,56 +334,56 @@ bool init_firmware(struct net_device *dev)
 		}
 
 		switch(init_step) {
-			case FW_INIT_STEP0_BOOT:
-				/* Download boot
-				 * initialize command descriptor.
-				 * will set polling bit when firmware code is also configured
-				 */
-				pfirmware->firmware_status = FW_STATUS_1_MOVE_BOOT_CODE;
+		case FW_INIT_STEP0_BOOT:
+			/* Download boot
+			 * initialize command descriptor.
+			 * will set polling bit when firmware code is also configured
+			 */
+			pfirmware->firmware_status = FW_STATUS_1_MOVE_BOOT_CODE;
 #ifdef RTL8190P
-				// To initialize IMEM, CPU move code  from 0x80000080, hence, we send 0x80 byte packet
-				rt_status = fwSendNullPacket(dev, RTL8190_CPU_START_OFFSET);
-				if(rt_status != true)
-				{
-					RT_TRACE(COMP_INIT, "fwSendNullPacket() fail ! \n");
-					goto  download_firmware_fail;
-				}
+			// To initialize IMEM, CPU move code  from 0x80000080, hence, we send 0x80 byte packet
+			rt_status = fwSendNullPacket(dev, RTL8190_CPU_START_OFFSET);
+			if(rt_status != true)
+			{
+				RT_TRACE(COMP_INIT, "fwSendNullPacket() fail ! \n");
+				goto  download_firmware_fail;
+			}
 #endif
-				//mdelay(1000);
-				/*
-				 * To initialize IMEM, CPU move code  from 0x80000080,
-				 * hence, we send 0x80 byte packet
-				 */
-				break;
-
-			case FW_INIT_STEP1_MAIN:
-				/* Download firmware code. Wait until Boot Ready and Turn on CPU */
-				pfirmware->firmware_status = FW_STATUS_2_MOVE_MAIN_CODE;
-
-				/* Check Put Code OK and Turn On CPU */
-				rt_status = CPUcheck_maincodeok_turnonCPU(dev);
-				if(rt_status != TRUE) {
-					RT_TRACE(COMP_ERR, "CPUcheck_maincodeok_turnonCPU fail!\n");
-					goto download_firmware_fail;
-				}
-
-				pfirmware->firmware_status = FW_STATUS_3_TURNON_CPU;
-				break;
-
-			case FW_INIT_STEP2_DATA:
-				/* download initial data code */
-				pfirmware->firmware_status = FW_STATUS_4_MOVE_DATA_CODE;
-				mdelay(1);
-
-				rt_status = CPUcheck_firmware_ready(dev);
-				if(rt_status != TRUE) {
-					RT_TRACE(COMP_ERR, "CPUcheck_firmware_ready fail(%d)!\n",rt_status);
-					goto download_firmware_fail;
-				}
-
-				/* wait until data code is initialized ready.*/
-				pfirmware->firmware_status = FW_STATUS_5_READY;
-				break;
+			//mdelay(1000);
+			/*
+			 * To initialize IMEM, CPU move code  from 0x80000080,
+			 * hence, we send 0x80 byte packet
+			 */
+			break;
+
+		case FW_INIT_STEP1_MAIN:
+			/* Download firmware code. Wait until Boot Ready and Turn on CPU */
+			pfirmware->firmware_status = FW_STATUS_2_MOVE_MAIN_CODE;
+
+			/* Check Put Code OK and Turn On CPU */
+			rt_status = CPUcheck_maincodeok_turnonCPU(dev);
+			if(rt_status != TRUE) {
+				RT_TRACE(COMP_ERR, "CPUcheck_maincodeok_turnonCPU fail!\n");
+				goto download_firmware_fail;
+			}
+
+			pfirmware->firmware_status = FW_STATUS_3_TURNON_CPU;
+			break;
+
+		case FW_INIT_STEP2_DATA:
+			/* download initial data code */
+			pfirmware->firmware_status = FW_STATUS_4_MOVE_DATA_CODE;
+			mdelay(1);
+
+			rt_status = CPUcheck_firmware_ready(dev);
+			if(rt_status != TRUE) {
+				RT_TRACE(COMP_ERR, "CPUcheck_firmware_ready fail(%d)!\n",rt_status);
+				goto download_firmware_fail;
+			}
+
+			/* wait until data code is initialized ready.*/
+			pfirmware->firmware_status = FW_STATUS_5_READY;
+			break;
 		}
 	}
 

drivers/staging/rtl8192u/r819xU_phy.c

@@ -957,56 +957,56 @@ u8 rtl8192_phy_ConfigRFWithHeaderFile(struct net_device* dev, RF90_RADIO_PATH_E
 	u8 ret = 0;
 
 	switch(eRFPath){
-		case RF90_PATH_A:
-			for(i = 0;i<RadioA_ArrayLength; i=i+2){
-
-				if(rtl819XRadioA_Array[i] == 0xfe){
-						mdelay(100);
-						continue;
-				}
-				rtl8192_phy_SetRFReg(dev, eRFPath, rtl819XRadioA_Array[i], bMask12Bits, rtl819XRadioA_Array[i+1]);
-				mdelay(1);
+	case RF90_PATH_A:
+		for(i = 0;i<RadioA_ArrayLength; i=i+2){
 
+			if(rtl819XRadioA_Array[i] == 0xfe){
+					mdelay(100);
+					continue;
 			}
-			break;
-		case RF90_PATH_B:
-			for(i = 0;i<RadioB_ArrayLength; i=i+2){
+			rtl8192_phy_SetRFReg(dev, eRFPath, rtl819XRadioA_Array[i], bMask12Bits, rtl819XRadioA_Array[i+1]);
+			mdelay(1);
 
-				if(rtl819XRadioB_Array[i] == 0xfe){
-						mdelay(100);
-						continue;
-				}
-				rtl8192_phy_SetRFReg(dev, eRFPath, rtl819XRadioB_Array[i], bMask12Bits, rtl819XRadioB_Array[i+1]);
-				mdelay(1);
+		}
+		break;
+	case RF90_PATH_B:
+		for(i = 0;i<RadioB_ArrayLength; i=i+2){
 
+			if(rtl819XRadioB_Array[i] == 0xfe){
+					mdelay(100);
+					continue;
 			}
-			break;
-		case RF90_PATH_C:
-			for(i = 0;i<RadioC_ArrayLength; i=i+2){
+			rtl8192_phy_SetRFReg(dev, eRFPath, rtl819XRadioB_Array[i], bMask12Bits, rtl819XRadioB_Array[i+1]);
+			mdelay(1);
 
-				if(rtl819XRadioC_Array[i] == 0xfe){
-						mdelay(100);
-						continue;
-				}
-				rtl8192_phy_SetRFReg(dev, eRFPath, rtl819XRadioC_Array[i], bMask12Bits, rtl819XRadioC_Array[i+1]);
-				mdelay(1);
+		}
+		break;
+	case RF90_PATH_C:
+		for(i = 0;i<RadioC_ArrayLength; i=i+2){
 
+			if(rtl819XRadioC_Array[i] == 0xfe){
+					mdelay(100);
+					continue;
 			}
-			break;
-		case RF90_PATH_D:
-			for(i = 0;i<RadioD_ArrayLength; i=i+2){
+			rtl8192_phy_SetRFReg(dev, eRFPath, rtl819XRadioC_Array[i], bMask12Bits, rtl819XRadioC_Array[i+1]);
+			mdelay(1);
 
-				if(rtl819XRadioD_Array[i] == 0xfe){
-						mdelay(100);
-						continue;
-				}
-				rtl8192_phy_SetRFReg(dev, eRFPath, rtl819XRadioD_Array[i], bMask12Bits, rtl819XRadioD_Array[i+1]);
-				mdelay(1);
+		}
+		break;
+	case RF90_PATH_D:
+		for(i = 0;i<RadioD_ArrayLength; i=i+2){
 
+			if(rtl819XRadioD_Array[i] == 0xfe){
+					mdelay(100);
+					continue;
 			}
-			break;
-		default:
-			break;
+			rtl8192_phy_SetRFReg(dev, eRFPath, rtl819XRadioD_Array[i], bMask12Bits, rtl819XRadioD_Array[i+1]);
+			mdelay(1);
+
+		}
+		break;
+	default:
+		break;
 	}
 
 	return ret;