Merge tag 'at91-4.5-dt2' of...

Merge tag 'at91-4.5-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into next/dt

Second batch of DT changes for 4.5:
- addition of sound nodes for sama5d2 and the xplained
- addition of a new patform by Landis+Gyr: VInCo

* tag 'at91-4.5-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
  ARM: at91/dt: sama5d2 Xplained: add pdmic node
  ARM: at91/dt: sama5d2: add pdmic node
  ARM: at91/dt: Add Support for the L+G VInCo platform
Signed-off-by: Olof Johansson <olof@lixom.net>

arch/arm/boot/dts/Makefile

@@ -50,7 +50,8 @@ dtb-$(CONFIG_SOC_SAM_V7) += \
 	sama5d36ek.dtb \
 	at91-sama5d4_ma5d4evk.dtb \
 	at91-sama5d4_xplained.dtb \
-	at91-sama5d4ek.dtb
+	at91-sama5d4ek.dtb \
+	at91-vinco.dtb
 dtb-$(CONFIG_ARCH_ATLAS6) += \
 	atlas6-evb.dtb
 dtb-$(CONFIG_ARCH_ATLAS7) += \

arch/arm/boot/dts/at91-sama5d2_xplained.dts

@@ -119,6 +119,16 @@ macb0: ethernet@f8008000 {
 				status = "okay";
 			};
 
+			pdmic@f8018000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_pdmic_default>;
+				atmel,model = "PDMIC @ sama5d2_xplained";
+				atmel,mic-min-freq = <1000000>;
+				atmel,mic-max-freq = <3246000>;
+				atmel,mic-offset = <0x0>;
+				status = "okay";
+			};
+
 			uart1: serial@f8020000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_uart1_default>;
@@ -289,6 +299,12 @@ pinctrl_macb0_default: macb0_default {
 					bias-disable;
 				};
 
+				pinctrl_pdmic_default: pdmic_default {
+					pinmux = <PIN_PB26__PDMIC_DAT>,
+						<PIN_PB27__PDMIC_CLK>;
+					bias-disable;
+				};
+
 				pinctrl_sdmmc0_default: sdmmc0_default {
 					cmd_data {
 						pinmux = <PIN_PA1__SDMMC0_CMD>,

arch/arm/boot/dts/at91-vinco.dts

+/*
+ * Device Tree file for VInCo platform
+ *
+ *  Copyright (C) 2014 Atmel,
+ *                2014 Nicolas Ferre <nicolas.ferre@atmel.com>
+ *   2015 Gregory CLEMENT <gregory.clement@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+#include "sama5d4.dtsi"
+
+/ {
+	model = "L+G VInCo platform";
+	compatible = "l+g,vinco", "atmel,sama5d4", "atmel,sama5";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory {
+		reg = <0x20000000 0x4000000>;
+	};
+
+	clocks {
+		slow_xtal {
+			clock-frequency = <32768>;
+		};
+
+		main_xtal {
+			clock-frequency = <12000000>;
+		};
+	};
+
+	ahb {
+		apb {
+
+			adc0: adc@fc034000 {
+				status = "okay"; /* Enable ADC IIO support */
+			};
+
+			mmc0: mmc@f8000000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0
+					     &pinctrl_mmc0_dat1_3
+					     &pinctrl_mmc0_dat4_7>;
+				vqmmc-supply = <&vcc_3v3_reg>;
+				vmmc-supply = <&vcc_3v3_reg>;
+				no-1-8-v;
+				status = "okay";
+				slot@0 {
+					reg = <0>;
+					bus-width = <8>;
+					non-removable;
+					broken-cd;
+					status = "okay";
+				};
+			};
+
+			spi0: spi@f8010000 {
+				cs-gpios = <&pioC 3 0>, <0>, <0>, <0>;
+				status = "okay";
+				m25p80@0 {
+					compatible = "n25q32b", "jedec,spi-nor";
+					spi-max-frequency = <50000000>;
+					reg = <0>;
+				};
+			};
+
+			i2c0: i2c@f8014000 {
+				status = "okay";
+			};
+
+			i2c1: i2c@f8018000 {
+				status = "okay";
+				/* kerkey security module */
+			};
+
+			macb0: ethernet@f8020000 {
+				phy-mode = "rmii";
+				status = "okay";
+
+				ethernet-phy@1 {
+					reg = <0x1>;
+					reset-gpios = <&pioE 8 GPIO_ACTIVE_HIGH>;
+					interrupt-parent = <&pioB>;
+					interrupts = <15 IRQ_TYPE_EDGE_FALLING>;
+				};
+
+			};
+
+			i2c2: i2c@f8024000 {
+				status = "okay";
+
+				rtc1: rtc@64 {
+					compatible = "epson,rx8900";
+					reg = <0x32>;
+				};
+			};
+
+			usart2: serial@fc008000 {
+				/* MBUS */
+				status = "okay";
+			};
+
+			usart3: serial@fc00c000 {
+				/* debug */
+				status = "okay";
+			};
+
+			usart4: serial@fc010000 {
+				/* LMN */
+				pinctrl-0 = <&pinctrl_usart4 &pinctrl_usart4_rts>;
+				linux,rs485-enabled-at-boot-time;
+				status = "okay";
+			};
+
+			macb1: ethernet@fc028000 {
+				phy-mode = "rmii";
+				status = "okay";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "okay";
+
+				ethernet-phy@1 {
+					reg = <0x1>;
+					interrupt-parent = <&pioB>;
+					interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
+					reset-gpios = <&pioE 6 GPIO_ACTIVE_HIGH>;
+				};
+			};
+
+			watchdog@fc068640 {
+				status = "okay";
+			};
+
+			pinctrl@fc06a000 {
+				board {
+					pinctrl_usba_vbus: usba_vbus {
+						atmel,pins =
+						<AT91_PIOE 31 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;
+					};
+				};
+			};
+		};
+
+		usb0: gadget@00400000 {
+			atmel,vbus-gpio = <&pioE 31 GPIO_ACTIVE_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usba_vbus>;
+			status = "disable";
+		};
+
+		usb1: ohci@00500000 {
+			num-ports = <3>;
+			atmel,vbus-gpio = <0
+					   &pioE 11 GPIO_ACTIVE_LOW
+					   &pioE 12 GPIO_ACTIVE_LOW
+					  >;
+			status = "disable";
+		};
+
+		usb2: ehci@00600000 {
+			/* 4G Modem */
+			status = "okay";
+		};
+
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		status = "okay";
+
+		led_err {
+			label = "err";
+			gpios = <&pioA 7 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led_rssi {
+			label = "rssi";
+			gpios = <&pioA 9 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led_tls {
+			label = "tls";
+			gpios = <&pioA 24 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led_lmc {
+			label = "lmc";
+			gpios = <&pioA 25 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led_wmt {
+			label = "wmt";
+			gpios = <&pioA 29 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led_pwr {
+			label = "pwr";
+			gpios = <&pioA 26 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+		};
+
+	};
+
+	vcc_3v3_reg: fixedregulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC 3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+};

arch/arm/boot/dts/sama5d2.dtsi

@@ -637,6 +637,12 @@ trng_clk: trng_clk {
 						atmel,clk-output-range = <0 83000000>;
 					};
 
+					pdmic_clk: pdmic_clk {
+						#clock-cells = <0>;
+						reg = <48>;
+						atmel,clk-output-range = <0 83000000>;
+					};
+
 					i2s0_clk: i2s0_clk {
 						#clock-cells = <0>;
 						reg = <54>;
@@ -763,6 +769,11 @@ pwm_gclk: pwm_gclk {
 						atmel,clk-output-range = <0 83000000>;
 					};
 
+					pdmic_gclk: pdmic_gclk {
+						#clock-cells = <0>;
+						reg = <48>;
+					};
+
 					i2s0_gclk: i2s0_gclk {
 						#clock-cells = <0>;
 						reg = <54>;
@@ -852,6 +863,19 @@ tcb1: timer@f8010000 {
 				clock-names = "t0_clk", "slow_clk";
 			};
 
+			pdmic: pdmic@f8018000 {
+				compatible = "atmel,sama5d2-pdmic";
+				reg = <0xf8018000 0x124>;
+				interrupts = <48 IRQ_TYPE_LEVEL_HIGH 7>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
+					| AT91_XDMAC_DT_PERID(50))>;
+				dma-names = "rx";
+				clocks = <&pdmic_clk>, <&pdmic_gclk>;
+				clock-names = "pclk", "gclk";
+				status = "disabled";
+			};
+
 			uart0: serial@f801c000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf801c000 0x100>;