ARM: dts: aspeed: Add Inventec Lanyang BMC

The Inventec Lanyang is Power 9 platform with ast2500 BMC.
Signed-off-by: Brian Yang <yang.brianc.w@inventec.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>

arch/arm/boot/dts/Makefile

@@ -1158,6 +1158,7 @@ dtb-$(CONFIG_ARCH_ZX) += zx296702-ad1.dtb
 dtb-$(CONFIG_ARCH_ASPEED) += \
 	aspeed-ast2500-evb.dtb \
 	aspeed-bmc-arm-centriq2400-rep.dtb \
+	aspeed-bmc-opp-lanyang.dtb \
 	aspeed-bmc-opp-palmetto.dtb \
 	aspeed-bmc-opp-romulus.dtb \
 	aspeed-bmc-opp-witherspoon.dtb \

arch/arm/boot/dts/aspeed-bmc-opp-lanyang.dts

+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (c) 2018 Inventec Corporation
+/dts-v1/;
+
+#include "aspeed-g5.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+
+/ {
+	model = "Lanyang BMC";
+	compatible = "inventec,lanyang-bmc", "aspeed,ast2500";
+
+	chosen {
+		stdout-path = &uart5;
+		bootargs = "console=ttyS4,115200 earlyprintk";
+	};
+
+	memory {
+		reg = <0x80000000 0x40000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		flash_memory: region@98000000 {
+			no-map;
+			reg = <0x98000000 0x04000000>; /* 64M */
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		sys_boot_status {
+			label = "System_boot_status";
+			gpios = <&gpio ASPEED_GPIO(B, 6) GPIO_ACTIVE_LOW>;
+		};
+
+		attention {
+			label = "Attention_locator";
+			gpios = <&gpio ASPEED_GPIO(B, 7) GPIO_ACTIVE_HIGH>;
+		};
+
+		plt_fault {
+			label = "Platform_fault";
+			gpios = <&gpio ASPEED_GPIO(B, 1) GPIO_ACTIVE_HIGH>;
+		};
+
+		hdd_fault {
+			label = "Onboard_drive_fault";
+			gpios = <&gpio ASPEED_GPIO(B, 3) GPIO_ACTIVE_HIGH>;
+		};
+		bmc_err {
+			lable = "BMC_fault";
+			gpios = <&gpio ASPEED_GPIO(H, 6) GPIO_ACTIVE_HIGH>;
+		};
+
+		sys_err {
+			lable = "Sys_fault";
+			gpios = <&gpio ASPEED_GPIO(H, 7) GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	fsi: gpio-fsi {
+		compatible = "fsi-master-gpio", "fsi-master";
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		clock-gpios = <&gpio ASPEED_GPIO(J, 0) GPIO_ACTIVE_HIGH>;
+		data-gpios = <&gpio ASPEED_GPIO(J, 1) GPIO_ACTIVE_HIGH>;
+		trans-gpios = <&gpio ASPEED_GPIO(D, 5) GPIO_ACTIVE_HIGH>;
+		enable-gpios = <&gpio ASPEED_GPIO(D, 0) GPIO_ACTIVE_HIGH>;
+		mux-gpios = <&gpio ASPEED_GPIO(H, 2) GPIO_ACTIVE_HIGH>;
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>,
+			<&adc 4>, <&adc 5>, <&adc 6>, <&adc 7>,
+			<&adc 8>, <&adc 9>, <&adc 10>, <&adc 11>,
+			<&adc 13>, <&adc 14>, <&adc 15>;
+	};
+
+	iio-hwmon-battery {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 12>;
+	};
+};
+
+&pwm_tacho {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm0_default &pinctrl_pwm1_default
+		&pinctrl_pwm2_default &pinctrl_pwm3_default>;
+
+	fan@0 {
+		reg = <0x00>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x00>;
+	};
+
+	fan@1 {
+		reg = <0x01>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x01>;
+	};
+
+	fan@2 {
+		reg = <0x02>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x02>;
+	};
+
+	fan@3 {
+		reg = <0x03>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x03>;
+	};
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+#include "openbmc-flash-layout.dtsi"
+	};
+};
+
+&spi1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi1_default>;
+
+	flash@0 {
+		status = "okay";
+		label = "pnor";
+		m25p,fast-read;
+	};
+};
+
+&spi2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi2ck_default
+		     &pinctrl_spi2cs0_default
+		     &pinctrl_spi2cs1_default
+		     &pinctrl_spi2miso_default
+		     &pinctrl_spi2mosi_default>;
+
+	flash@0 {
+		status = "okay";
+	};
+};
+
+&uart1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_txd1_default
+		     &pinctrl_rxd1_default>;
+};
+
+&lpc_ctrl {
+	status = "okay";
+	memory-region = <&flash_memory>;
+	flash = <&spi1>;
+};
+
+&lpc_snoop {
+	status = "okay";
+	snoop-ports = <0x80>;
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&mac0 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii1_default>;
+	use-ncsi;
+};
+
+&mac1 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii2_default &pinctrl_mdio2_default>;
+};
+
+&i2c0 {
+	status = "okay";
+
+	eeprom@55 {
+		compatible = "atmel,24c64";
+		reg = <0x55>;
+		pagesize = <32>;
+	};
+
+	rtc@68 {
+		compatible = "nxp,pcf8523";
+		reg = <0x68>;
+	};
+
+	tmp75@48 {
+		compatible = "ti,tmp75";
+		reg = <0x48>;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&i2c6 {
+	status = "okay";
+};
+
+&i2c7 {
+	status = "okay";
+};
+
+&i2c8 {
+	status = "okay";
+};
+
+&i2c9 {
+	status = "okay";
+};
+
+&i2c10 {
+	status = "okay";
+};
+
+&i2c11 {
+	status = "okay";
+};
+
+&vuart {
+	status = "okay";
+};
+
+&gfx {
+	status = "okay";
+};
+
+&pinctrl {
+	aspeed,external-nodes = <&gfx &lhc>;
+};
+
+&gpio {
+	pin_gpio_b0 {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(B, 0) GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "BMC_HDD1_PWR_EN";
+	};
+
+	pin_gpio_b5 {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(B, 5) GPIO_ACTIVE_HIGH>;
+		input;
+		line-name = "BMC_USB1_OCI2";
+	};
+
+	pin_gpio_h5 {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(H, 5) GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "BMC_CP0_PERST_ENABLE_R";
+	};
+
+	pin_gpio_z2 {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(Z, 2) GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "RST_PCA9546_U177_N";
+	};
+
+	pin_gpio_aa6 {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(AA, 6) GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "BMC_CP0_RESET_N";
+	};
+
+	pin_gpio_aa7 {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(AA, 7) GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "BMC_TPM_RESET_N";
+	};
+
+	pin_gpio_ab0 {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(AB, 0) GPIO_ACTIVE_LOW>;
+		output-high;
+		line-name = "BMC_USB_PWRON_N";
+	};
+};
+
+&ibt {
+	status = "okay";
+};
+
+&adc {
+	status = "okay";
+};
+