ARM: dts: am43x-epos: Add qspi device

This patch adds qspi nodes for am43xx SOC devices.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

arch/arm/boot/dts/am4372.dtsi

@@ -829,6 +829,17 @@ usb2: usb@483d0000 {
 				status = "disabled";
 			};
 		};
+
+		qspi: qspi@47900000 {
+			compatible = "ti,am4372-qspi";
+			reg = <0x47900000 0x100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			ti,hwmods = "qspi";
+			interrupts = <0 138 0x4>;
+			num-cs = <4>;
+			status = "disabled";
+		};
 	};
 };
 

arch/arm/boot/dts/am43x-epos-evm.dts

@@ -138,6 +138,17 @@ mmc1_pins: pinmux_mmc1_pins {
 				0x160 (PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */
 			>;
 		};
+
+		qspi1_default: qspi1_default {
+			pinctrl-single,pins = <
+				0x7c (PIN_INPUT_PULLUP | MUX_MODE3)
+				0x88 (PIN_INPUT_PULLUP | MUX_MODE2)
+				0x90 (PIN_INPUT_PULLUP | MUX_MODE3)
+				0x94 (PIN_INPUT_PULLUP | MUX_MODE3)
+				0x98 (PIN_INPUT_PULLUP | MUX_MODE3)
+				0x9c (PIN_INPUT_PULLUP | MUX_MODE3)
+			>;
+		};
 	};
 
 	matrix_keypad: matrix_keypad@0 {
@@ -385,3 +396,55 @@ &usb2 {
 	dr_mode = "host";
 	status = "okay";
 };
+
+&qspi {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&qspi1_default>;
+
+	spi-max-frequency = <48000000>;
+	m25p80@0 {
+		compatible = "mx66l51235l";
+		spi-max-frequency = <48000000>;
+		reg = <0>;
+		spi-cpol;
+		spi-cpha;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		/* MTD partition table.
+		 * The ROM checks the first 512KiB
+		 * for a valid file to boot(XIP).
+		 */
+		partition@0 {
+			label = "QSPI.U_BOOT";
+			reg = <0x00000000 0x000080000>;
+		};
+		partition@1 {
+			label = "QSPI.U_BOOT.backup";
+			reg = <0x00080000 0x00080000>;
+		};
+		partition@2 {
+			label = "QSPI.U-BOOT-SPL_OS";
+			reg = <0x00100000 0x00010000>;
+		};
+		partition@3 {
+			label = "QSPI.U_BOOT_ENV";
+			reg = <0x00110000 0x00010000>;
+		};
+		partition@4 {
+			label = "QSPI.U-BOOT-ENV.backup";
+			reg = <0x00120000 0x00010000>;
+		};
+		partition@5 {
+			label = "QSPI.KERNEL";
+			reg = <0x00130000 0x0800000>;
+		};
+		partition@6 {
+			label = "QSPI.FILESYSTEM";
+			reg = <0x00930000 0x36D0000>;
+		};
+	};
+};