mac80211: properly remove RX_ENC_FLAG_40MHZ

Somehow I missed this in my RX rate cleanup series, causing some
drivers to not report correct bandwidth since this flag isn't
used by mac80211 anymore. Fix this, and make hwsim also report
higher bandwidths appropriately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

drivers/net/wireless/ath/ath9k/ar9003_mac.c

@@ -522,7 +522,7 @@ int ath9k_hw_process_rxdesc_edma(struct ath_hw *ah, struct ath_rx_status *rxs,
 	rxs->rs_moreaggr = (rxsp->status11 & AR_RxMoreAggr) ? 1 : 0;
 	rxs->rs_antenna = (MS(rxsp->status4, AR_RxAntenna) & 0x7);
 	rxs->enc_flags |= (rxsp->status4 & AR_GI) ? RX_ENC_FLAG_SHORT_GI : 0;
-	rxs->enc_flags |= (rxsp->status4 & AR_2040) ? RX_ENC_FLAG_40MHZ : 0;
+	rxs->bw = (rxsp->status4 & AR_2040) ? RATE_INFO_BW_40 : RATE_INFO_BW_20;
 
 	rxs->evm0 = rxsp->status6;
 	rxs->evm1 = rxsp->status7;

drivers/net/wireless/ath/ath9k/mac.c

@@ -580,8 +580,8 @@ int ath9k_hw_rxprocdesc(struct ath_hw *ah, struct ath_desc *ds,
 	/* directly mapped flags for ieee80211_rx_status */
 	rs->enc_flags |=
 		(ads.ds_rxstatus3 & AR_GI) ? RX_ENC_FLAG_SHORT_GI : 0;
-	rs->enc_flags |=
-		(ads.ds_rxstatus3 & AR_2040) ? RX_ENC_FLAG_40MHZ : 0;
+	rs->bw = (ads.ds_rxstatus3 & AR_2040) ? RATE_INFO_BW_40 :
+						RATE_INFO_BW_20;
 	if (AR_SREV_9280_20_OR_LATER(ah))
 		rs->enc_flags |=
 			(ads.ds_rxstatus3 & AR_STBC) ?

drivers/net/wireless/intel/iwlegacy/4965-mac.c

@@ -734,7 +734,9 @@ il4965_hdl_rx(struct il_priv *il, struct il_rx_buf *rxb)
 	if (rate_n_flags & RATE_MCS_HT_MSK)
 		rx_status.encoding = RX_ENC_HT;
 	if (rate_n_flags & RATE_MCS_HT40_MSK)
-		rx_status.enc_flags |= RX_ENC_FLAG_40MHZ;
+		rx_status.bw = RATE_INFO_BW_40;
+	else
+		rx_status.bw = RATE_INFO_BW_20;
 	if (rate_n_flags & RATE_MCS_SGI_MSK)
 		rx_status.enc_flags |= RX_ENC_FLAG_SHORT_GI;
 

drivers/net/wireless/intel/iwlwifi/dvm/rx.c

@@ -889,7 +889,9 @@ static void iwlagn_rx_reply_rx(struct iwl_priv *priv,
 	if (rate_n_flags & RATE_MCS_HT_MSK)
 		rx_status.encoding = RX_ENC_HT;
 	if (rate_n_flags & RATE_MCS_HT40_MSK)
-		rx_status.enc_flags |= RX_ENC_FLAG_40MHZ;
+		rx_status.bw = RATE_INFO_BW_40;
+	else
+		rx_status.bw = RATE_INFO_BW_20;
 	if (rate_n_flags & RATE_MCS_SGI_MSK)
 		rx_status.enc_flags |= RX_ENC_FLAG_SHORT_GI;
 	if (rate_n_flags & RATE_MCS_GF_MSK)

drivers/net/wireless/mac80211_hwsim.c

@@ -1201,7 +1201,13 @@ static bool mac80211_hwsim_tx_frame_no_nl(struct ieee80211_hw *hw,
 			rx_status.encoding = RX_ENC_HT;
 	}
 	if (info->control.rates[0].flags & IEEE80211_TX_RC_40_MHZ_WIDTH)
-		rx_status.enc_flags |= RX_ENC_FLAG_40MHZ;
+		rx_status.bw = RATE_INFO_BW_40;
+	else if (info->control.rates[0].flags & IEEE80211_TX_RC_80_MHZ_WIDTH)
+		rx_status.bw = RATE_INFO_BW_80;
+	else if (info->control.rates[0].flags & IEEE80211_TX_RC_160_MHZ_WIDTH)
+		rx_status.bw = RATE_INFO_BW_160;
+	else
+		rx_status.bw = RATE_INFO_BW_20;
 	if (info->control.rates[0].flags & IEEE80211_TX_RC_SHORT_GI)
 		rx_status.enc_flags |= RX_ENC_FLAG_SHORT_GI;
 	/* TODO: simulate real signal strength (and optional packet loss) */

include/net/mac80211.h

@@ -1141,7 +1141,6 @@ enum mac80211_rx_flags {
  * enum mac80211_rx_encoding_flags - MCS & bandwidth flags
  *
  * @RX_ENC_FLAG_SHORTPRE: Short preamble was used for this frame
- * @RX_ENC_FLAG_40MHZ: HT40 (40 MHz) was used
  * @RX_ENC_FLAG_SHORT_GI: Short guard interval was used
  * @RX_ENC_FLAG_HT_GF: This frame was received in a HT-greenfield transmission,
  *	if the driver fills this value it should add
@@ -1153,7 +1152,6 @@ enum mac80211_rx_flags {
  */
 enum mac80211_rx_encoding_flags {
 	RX_ENC_FLAG_SHORTPRE		= BIT(0),
-	RX_ENC_FLAG_40MHZ		= BIT(1),
 	RX_ENC_FLAG_SHORT_GI		= BIT(2),
 	RX_ENC_FLAG_HT_GF		= BIT(3),
 	RX_ENC_FLAG_STBC_MASK		= BIT(4) | BIT(5),