Commit 301bc067 authored by Maxime Ripard's avatar Maxime Ripard Committed by Tomi Valkeinen

video: ssd1307fb: Make use of horizontal addressing mode

By default, the ssd1307 controller uses an addressing mode called page
addressing. This mode only increments the column cursor in memory when
writing data but will not increments the page cursor when we are at the
end of the page.

However, the controller supports another addressing mode, called
horizontal addressing, that will maintain both the page and column
cursors when writing data to the controller.

That means that we can just remove the code that increments the current
page address and reset the column cursor when reaching the end of the
line, allowing to have a lower data overhead, and a simpler driver.
Signed-off-by: default avatarMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: default avatarTomi Valkeinen <tomi.valkeinen@ti.com>
parent 3394e645
......@@ -19,6 +19,12 @@
#define SSD1307FB_DATA 0x40
#define SSD1307FB_COMMAND 0x80
#define SSD1307FB_SET_ADDRESS_MODE 0x20
#define SSD1307FB_SET_ADDRESS_MODE_HORIZONTAL (0x00)
#define SSD1307FB_SET_ADDRESS_MODE_VERTICAL (0x01)
#define SSD1307FB_SET_ADDRESS_MODE_PAGE (0x02)
#define SSD1307FB_SET_COL_RANGE 0x21
#define SSD1307FB_SET_PAGE_RANGE 0x22
#define SSD1307FB_CONTRAST 0x81
#define SSD1307FB_CHARGE_PUMP 0x8d
#define SSD1307FB_SEG_REMAP_ON 0xa1
......@@ -135,9 +141,15 @@ static inline int ssd1307fb_write_data(struct i2c_client *client, u8 data)
static void ssd1307fb_update_display(struct ssd1307fb_par *par)
{
struct ssd1307fb_array *array;
u8 *vmem = par->info->screen_base;
int i, j, k;
array = ssd1307fb_alloc_array(par->width * par->height / 8,
SSD1307FB_DATA);
if (!array)
return;
/*
* The screen is divided in pages, each having a height of 8
* pixels, and the width of the screen. When sending a byte of
......@@ -168,29 +180,22 @@ static void ssd1307fb_update_display(struct ssd1307fb_par *par)
*/
for (i = 0; i < (par->height / 8); i++) {
struct ssd1307fb_array *array;
ssd1307fb_write_cmd(par->client,
SSD1307FB_START_PAGE_ADDRESS + i + par->page_offset);
ssd1307fb_write_cmd(par->client, 0x00);
ssd1307fb_write_cmd(par->client, 0x10);
array = ssd1307fb_alloc_array(par->width, SSD1307FB_DATA);
for (j = 0; j < par->width; j++) {
array->data[j] = 0;
u32 array_idx = i * par->width + j;
array->data[array_idx] = 0;
for (k = 0; k < 8; k++) {
u32 page_length = par->width * i;
u32 index = page_length + (par->width * k + j) / 8;
u8 byte = *(vmem + index);
u8 bit = byte & (1 << (j % 8));
bit = bit >> (j % 8);
array->data[j] |= bit << k;
array->data[array_idx] |= bit << k;
}
}
ssd1307fb_write_array(par->client, array, par->width);
kfree(array);
}
ssd1307fb_write_array(par->client, array, par->width * par->height / 8);
kfree(array);
}
......@@ -371,6 +376,26 @@ static int ssd1307fb_ssd1306_init(struct ssd1307fb_par *par)
if (ret < 0)
return ret;
/* Switch to horizontal addressing mode */
ret = ssd1307fb_write_cmd(par->client, SSD1307FB_SET_ADDRESS_MODE);
ret = ret & ssd1307fb_write_cmd(par->client,
SSD1307FB_SET_ADDRESS_MODE_HORIZONTAL);
if (ret < 0)
return ret;
ret = ssd1307fb_write_cmd(par->client, SSD1307FB_SET_COL_RANGE);
ret = ret & ssd1307fb_write_cmd(par->client, 0x0);
ret = ret & ssd1307fb_write_cmd(par->client, par->width - 1);
if (ret < 0)
return ret;
ret = ssd1307fb_write_cmd(par->client, SSD1307FB_SET_PAGE_RANGE);
ret = ret & ssd1307fb_write_cmd(par->client, 0x0);
ret = ret & ssd1307fb_write_cmd(par->client,
par->page_offset + (par->height / 8) - 1);
if (ret < 0)
return ret;
/* Turn on the display */
ret = ssd1307fb_write_cmd(par->client, SSD1307FB_DISPLAY_ON);
if (ret < 0)
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment