Commit 32500473 authored by Slawomir Kolodynski's avatar Slawomir Kolodynski Committed by Russell King

[SERIAL] Add support for SBS Tech. Inc. PMC-OCTPRO and P-OCTAL cards.

Patch from Slawomir Kolodynski
parent a063296d
......@@ -20,6 +20,7 @@
#include <linux/string.h>
#include <linux/kernel.h>
#include <linux/slab.h>
#include <linux/delay.h>
#include <linux/tty.h>
#include <linux/serial.h>
#include <linux/serial_core.h>
......@@ -305,6 +306,72 @@ static void __devexit pci_plx9050_exit(struct pci_dev *dev)
}
}
/* SBS Technologies Inc. PMC-OCTPRO and P-OCTAL cards */
static int
sbs_setup(struct pci_dev *dev, struct pci_board *board,
struct serial_struct *req, int idx)
{
unsigned int bar, offset = board->first_offset, maxnr;
bar = 0;
if (idx < 4) {
/* first four channels map to 0, 0x100, 0x200, 0x300 */
offset += idx * board->uart_offset;
} else if (idx < 8) {
/* last four channels map to 0x1000, 0x1100, 0x1200, 0x1300 */
offset += idx * board->uart_offset + 0xC00;
} else /* we have only 8 ports on PMC-OCTALPRO */
return 1;
return setup_port(dev, req, bar, offset, board->reg_shift);
}
/*
* This does initialization for PMC OCTALPRO cards:
* maps the device memory, resets the UARTs (needed, bc
* if the module is removed and inserted again, the card
* is in the sleep mode) and enables global interrupt.
*/
/* global control register offset for SBS PMC-OctalPro */
#define OCT_REG_CR_OFF 0x500
static int __devinit sbs_init(struct pci_dev *dev)
{
u8 * p;
p = ioremap(pci_resource_start(dev, 0),pci_resource_len(dev,0));
if (p == NULL)
return -ENOMEM;
/* Set bit-4 Control Register (UART RESET) in to reset the uarts */
writeb(0x10,p + OCT_REG_CR_OFF);
udelay(50);
writeb(0x0,p + OCT_REG_CR_OFF);
/* Set bit-2 (INTENABLE) of Control Register */
writeb(0x4, p + OCT_REG_CR_OFF);
iounmap(p);
return 0;
}
/*
* Disables the global interrupt of PMC-OctalPro
*/
static void __devexit sbs_exit(struct pci_dev *dev)
{
u8 * p;
p = ioremap(pci_resource_start(dev, 0),pci_resource_len(dev,0));
if (p != NULL) {
writeb(0, p + OCT_REG_CR_OFF);
}
iounmap(p);
}
/*
* SIIG serial cards have an PCI interface chip which also controls
* the UART clocking frequency. Each UART can be clocked independently
......@@ -534,6 +601,15 @@ pci_default_setup(struct pci_dev *dev, struct pci_board *board,
return setup_port(dev, req, bar, offset, board->reg_shift);
}
/* This should be in linux/pci_ids.h */
#define PCI_VENDOR_ID_SBSMODULARIO 0x124B
#define PCI_SUBVENDOR_ID_SBSMODULARIO 0x124B
#define PCI_DEVICE_ID_OCTPRO 0x0001
#define PCI_SUBDEVICE_ID_OCTPRO232 0x0108
#define PCI_SUBDEVICE_ID_OCTPRO422 0x0208
#define PCI_SUBDEVICE_ID_POCTAL232 0x0308
#define PCI_SUBDEVICE_ID_POCTAL422 0x0408
/*
* Master list of serial port init/setup/exit quirks.
* This does not describe the general nature of the port.
......@@ -618,6 +694,55 @@ static struct pci_serial_quirk pci_serial_quirks[] = {
.setup = pci_default_setup,
.exit = __devexit_p(pci_plx9050_exit),
},
/*
* SBS Technologies, Inc., PMC-OCTALPRO 232
*/
{
.vendor = PCI_VENDOR_ID_SBSMODULARIO,
.device = PCI_DEVICE_ID_OCTPRO,
.subvendor = PCI_SUBVENDOR_ID_SBSMODULARIO,
.subdevice = PCI_SUBDEVICE_ID_OCTPRO232,
.init = sbs_init,
.setup = sbs_setup,
.exit = sbs_exit
},
/*
* SBS Technologies, Inc., PMC-OCTALPRO 422
*/
{
.vendor = PCI_VENDOR_ID_SBSMODULARIO,
.device = PCI_DEVICE_ID_OCTPRO,
.subvendor = PCI_SUBVENDOR_ID_SBSMODULARIO,
.subdevice = PCI_SUBDEVICE_ID_OCTPRO422,
.init = sbs_init,
.setup = sbs_setup,
.exit = sbs_exit
},
/*
* SBS Technologies, Inc., P-Octal 232
*/
{
.vendor = PCI_VENDOR_ID_SBSMODULARIO,
.device = PCI_DEVICE_ID_OCTPRO,
.subvendor = PCI_SUBVENDOR_ID_SBSMODULARIO,
.subdevice = PCI_SUBDEVICE_ID_POCTAL232,
.init = sbs_init,
.setup = sbs_setup,
.exit = sbs_exit
},
/*
* SBS Technologies, Inc., P-Octal 422
*/
{
.vendor = PCI_VENDOR_ID_SBSMODULARIO,
.device = PCI_DEVICE_ID_OCTPRO,
.subvendor = PCI_SUBVENDOR_ID_SBSMODULARIO,
.subdevice = PCI_SUBDEVICE_ID_POCTAL422,
.init = sbs_init,
.setup = sbs_setup,
.exit = sbs_exit
},
/*
* SIIG cards.
* It is not clear whether these could be collapsed.
......@@ -944,8 +1069,19 @@ enum pci_board_num_t {
pbn_computone_4,
pbn_computone_6,
pbn_computone_8,
pbn_sbsxrsio,
};
/*
* uart_offset - the space between channels
* reg_shift - describes how the UART registers are mapped
* to PCI memory by the card.
* For example IER register on SBS, Inc. PMC-OctPro is located at
* offset 0x10 from the UART base, while UART_IER is defined as 1
* in include/linux/serial_reg.h,
* see first lines of serial_in() and serial_out() in 8250.c
*/
static struct pci_board pci_boards[] __devinitdata = {
[pbn_default] = {
.flags = FL_BASE0,
......@@ -1348,6 +1484,13 @@ static struct pci_board pci_boards[] __devinitdata = {
.reg_shift = 2,
.first_offset = 0x200,
},
[pbn_sbsxrsio] = {
.flags = FL_BASE0,
.num_ports = 8,
.base_baud = 460800,
.uart_offset = 256,
.reg_shift = 4,
}
};
/*
......@@ -1755,27 +1898,44 @@ static struct pci_device_id serial_pci_tbl[] = {
0x10b5, 0x106a, 0, 0,
pbn_plx_romulus },
{ PCI_VENDOR_ID_QUATECH, PCI_DEVICE_ID_QUATECH_QSC100,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b1_4_115200 },
{ PCI_VENDOR_ID_QUATECH, PCI_DEVICE_ID_QUATECH_DSC100,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b1_2_115200 },
{ PCI_VENDOR_ID_QUATECH, PCI_DEVICE_ID_QUATECH_ESC100D,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b1_8_115200 },
{ PCI_VENDOR_ID_QUATECH, PCI_DEVICE_ID_QUATECH_ESC100M,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b1_8_115200 },
{ PCI_VENDOR_ID_SPECIALIX, PCI_DEVICE_ID_OXSEMI_16PCI954,
PCI_VENDOR_ID_SPECIALIX, PCI_SUBDEVICE_ID_SPECIALIX_SPEED4, 0, 0,
PCI_VENDOR_ID_SPECIALIX, PCI_SUBDEVICE_ID_SPECIALIX_SPEED4, 0, 0,
pbn_b0_4_921600 },
{ PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_16PCI954,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_4_115200 },
{ PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_16PCI952,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_bt_2_921600 },
/*
* SBS Technologies, Inc. P-Octal and PMC-OCTPRO cards,
* from skokodyn@yahoo.com
*/
{ PCI_VENDOR_ID_SBSMODULARIO, PCI_DEVICE_ID_OCTPRO,
PCI_SUBVENDOR_ID_SBSMODULARIO, PCI_SUBDEVICE_ID_OCTPRO232, 0, 0,
pbn_sbsxrsio },
{ PCI_VENDOR_ID_SBSMODULARIO, PCI_DEVICE_ID_OCTPRO,
PCI_SUBVENDOR_ID_SBSMODULARIO, PCI_SUBDEVICE_ID_OCTPRO422, 0, 0,
pbn_sbsxrsio },
{ PCI_VENDOR_ID_SBSMODULARIO, PCI_DEVICE_ID_OCTPRO,
PCI_SUBVENDOR_ID_SBSMODULARIO, PCI_SUBDEVICE_ID_POCTAL232, 0, 0,
pbn_sbsxrsio },
{ PCI_VENDOR_ID_SBSMODULARIO, PCI_DEVICE_ID_OCTPRO,
PCI_SUBVENDOR_ID_SBSMODULARIO, PCI_SUBDEVICE_ID_POCTAL422, 0, 0,
pbn_sbsxrsio },
/*
* Digitan DS560-558, from jimd@esoft.com
*/
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment