Commit 33cdce62 authored by Ian Abbott's avatar Ian Abbott Committed by Greg Kroah-Hartman

staging: comedi: addi_apci_1032: conform to new INSN_CONFIG_DIGITAL_TRIG

Conform to the new definition of the `INSN_CONFIG_DIGITAL_TRIG`
configuration instruction.

Return an error if the 'trigger number' in `data[1]` is non-zero or if
the configuration operation in `data[2]` is not supported.  Deal with
the 'left-shift' amount in `data[3]`.

The trigger's input channels can only be configured as a set of rising
and falling edges ('OR' mode) or as a set of high and low levels ('AND'
mode).  Preserve the old input channels to the right of the 'left-shift'
value except when switching modes.

(The 'left-shift' support is a bit of an overkill for this driver since
the trigger only has 16 input channels.)
Signed-off-by: default avatarIan Abbott <abbotti@mev.co.uk>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
parent c3be5c7f
......@@ -86,10 +86,14 @@ static int apci1032_reset(struct comedi_device *dev)
* The COS interrupt must be configured before it can be enabled.
*
* data[0] : INSN_CONFIG_DIGITAL_TRIG
* data[1] : 0 = OR (edge) interrupts
* 1 = AND (level) interrupts
* data[2] : rising-edge/high level channels
* data[3] : falling-edge/low level channels
* data[1] : trigger number (= 0)
* data[2] : configuration operation:
* COMEDI_DIGITAL_TRIG_DISABLE = no interrupts
* COMEDI_DIGITAL_TRIG_ENABLE_EDGES = OR (edge) interrupts
* COMEDI_DIGITAL_TRIG_ENABLE_LEVELS = AND (level) interrupts
* data[3] : left-shift for data[4] and data[5]
* data[4] : rising-edge/high level channels
* data[5] : falling-edge/low level channels
*/
static int apci1032_cos_insn_config(struct comedi_device *dev,
struct comedi_subdevice *s,
......@@ -97,21 +101,59 @@ static int apci1032_cos_insn_config(struct comedi_device *dev,
unsigned int *data)
{
struct apci1032_private *devpriv = dev->private;
unsigned int shift, oldmask;
switch (data[0]) {
case INSN_CONFIG_DIGITAL_TRIG:
devpriv->mode1 = data[2];
devpriv->mode2 = data[3];
if (devpriv->mode1 || devpriv->mode2) {
devpriv->ctrl = APCI1032_CTRL_INT_ENA;
if (data[1] == 1)
devpriv->ctrl = APCI1032_CTRL_INT_AND;
else
devpriv->ctrl = APCI1032_CTRL_INT_OR;
} else {
if (data[1] != 0)
return -EINVAL;
shift = data[3];
oldmask = (1U << shift) - 1;
switch (data[2]) {
case COMEDI_DIGITAL_TRIG_DISABLE:
devpriv->ctrl = 0;
devpriv->mode1 = 0;
devpriv->mode2 = 0;
apci1032_reset(dev);
break;
case COMEDI_DIGITAL_TRIG_ENABLE_EDGES:
if (devpriv->ctrl != (APCI1032_CTRL_INT_ENA |
APCI1032_CTRL_INT_OR)) {
/* switching to 'OR' mode */
devpriv->ctrl = APCI1032_CTRL_INT_ENA |
APCI1032_CTRL_INT_OR;
/* wipe old channels */
devpriv->mode1 = 0;
devpriv->mode2 = 0;
} else {
/* preserve unspecified channels */
devpriv->mode1 &= oldmask;
devpriv->mode2 &= oldmask;
}
/* configure specified channels */
devpriv->mode1 |= data[4] << shift;
devpriv->mode2 |= data[5] << shift;
break;
case COMEDI_DIGITAL_TRIG_ENABLE_LEVELS:
if (devpriv->ctrl != (APCI1032_CTRL_INT_ENA |
APCI1032_CTRL_INT_AND)) {
/* switching to 'AND' mode */
devpriv->ctrl = APCI1032_CTRL_INT_ENA |
APCI1032_CTRL_INT_AND;
/* wipe old channels */
devpriv->mode1 = 0;
devpriv->mode2 = 0;
} else {
/* preserve unspecified channels */
devpriv->mode1 &= oldmask;
devpriv->mode2 &= oldmask;
}
/* configure specified channels */
devpriv->mode1 |= data[4] << shift;
devpriv->mode2 |= data[5] << shift;
break;
default:
return -EINVAL;
}
break;
default:
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment