Merge branch 'imx-fb-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx into devel

Conflicts:

	drivers/video/mx3fb.c

arch/arm/plat-mxc/include/mach/mx3fb.h

@@ -14,25 +14,25 @@
 #include <linux/fb.h>
 
 /* Proprietary FB_SYNC_ flags */
-#define FB_SYNC_OE_ACT_HIGH    0x80000000
-#define FB_SYNC_CLK_INVERT     0x40000000
-#define FB_SYNC_DATA_INVERT    0x20000000
-#define FB_SYNC_CLK_IDLE_EN    0x10000000
-#define FB_SYNC_SHARP_MODE     0x08000000
-#define FB_SYNC_SWAP_RGB       0x04000000
-#define FB_SYNC_CLK_SEL_EN     0x02000000
+#define FB_SYNC_OE_ACT_HIGH	0x80000000
+#define FB_SYNC_CLK_INVERT	0x40000000
+#define FB_SYNC_DATA_INVERT	0x20000000
+#define FB_SYNC_CLK_IDLE_EN	0x10000000
+#define FB_SYNC_SHARP_MODE	0x08000000
+#define FB_SYNC_SWAP_RGB	0x04000000
+#define FB_SYNC_CLK_SEL_EN	0x02000000
 
 /**
  * struct mx3fb_platform_data - mx3fb platform data
  *
- * @dma_dev:   pointer to the dma-device, used for dma-slave connection
- * @mode:      pointer to a platform-provided per mxc_register_fb() videomode
+ * @dma_dev:	pointer to the dma-device, used for dma-slave connection
+ * @mode:	pointer to a platform-provided per mxc_register_fb() videomode
  */
 struct mx3fb_platform_data {
-       struct device                   *dma_dev;
-       const char                      *name;
-       const struct fb_videomode       *mode;
-       int                             num_modes;
+	struct device			*dma_dev;
+	const char			*name;
+	const struct fb_videomode	*mode;
+	int				num_modes;
 };
 
 #endif

drivers/video/Kconfig

@@ -2120,16 +2120,16 @@ config FB_PRE_INIT_FB
 	  the bootloader.
 
 config FB_MX3
-       tristate "MX3 Framebuffer support"
-       depends on FB && MX3_IPU
-       select FB_CFB_FILLRECT
-       select FB_CFB_COPYAREA
-       select FB_CFB_IMAGEBLIT
-       default y
-       help
-         This is a framebuffer device for the i.MX31 LCD Controller. So
-         far only synchronous displays are supported. If you plan to use
-         an LCD display with your i.MX31 system, say Y here.
+	tristate "MX3 Framebuffer support"
+	depends on FB && MX3_IPU
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	default y
+	help
+	  This is a framebuffer device for the i.MX31 LCD Controller. So
+	  far only synchronous displays are supported. If you plan to use
+	  an LCD display with your i.MX31 system, say Y here.
 
 config FB_BROADSHEET
 	tristate "E-Ink Broadsheet/Epson S1D13521 controller support"

drivers/video/Makefile

@@ -133,7 +133,7 @@ obj-$(CONFIG_FB_VGA16)            += vga16fb.o
 obj-$(CONFIG_FB_OF)               += offb.o
 obj-$(CONFIG_FB_BF54X_LQ043)	  += bf54x-lq043fb.o
 obj-$(CONFIG_FB_BFIN_T350MCQB)	  += bfin-t350mcqb-fb.o
-obj-$(CONFIG_FB_MX3)              += mx3fb.o
+obj-$(CONFIG_FB_MX3)		  += mx3fb.o
 
 # the test framebuffer is last
 obj-$(CONFIG_FB_VIRTUAL)          += vfb.o