Commit 3b2039b2 authored by Greg Ungerer's avatar Greg Ungerer

m68knommu: make 528x QSPI platform addressing consistent

If we make all QSPI (SPI protocol) addressing consistent across all ColdFire
family members then we will be able to remove the duplicated plaform data
and code and use a single setup for all.

So modify the ColdFire 528x QSPI addressing so that:

. base addresses are absolute (not relative to MBAR peripheral register)
. use a common name for IRQs used
. move chip select definitions (CS) to appropriate header
Signed-off-by: default avatarGreg Ungerer <gerg@uclinux.org>
parent 6c84a60e
......@@ -51,6 +51,8 @@
#define MCF_IRQ_FECTX0 (MCFINT_VECBASE + MCFINT_FECTX0)
#define MCF_IRQ_FECENTC0 (MCFINT_VECBASE + MCFINT_FECENTC0)
#define MCF_IRQ_QSPI (MCFINT_VECBASE + MCFINT_QSPI)
/*
* SDRAM configuration registers.
*/
......@@ -81,6 +83,17 @@
#define MCFFEC_BASE0 (MCF_IPSBAR + 0x00001000)
#define MCFFEC_SIZE0 0x800
/*
* QSPI module.
*/
#define MCFQSPI_IOBASE (MCF_IPSBAR + 0x340)
#define MCFQSPI_SIZE 0x40
#define MCFQSPI_CS0 147
#define MCFQSPI_CS1 148
#define MCFQSPI_CS2 149
#define MCFQSPI_CS3 150
/*
* GPIO registers
*/
......
......@@ -21,9 +21,7 @@
#ifndef mcfqspi_h
#define mcfqspi_h
#if defined(CONFIG_M528x)
#define MCFQSPI_IOBASE (MCF_IPSBAR + 0x340)
#elif defined(CONFIG_M532x)
#if defined(CONFIG_M532x)
#define MCFQSPI_IOBASE 0xFC058000
#endif
#define MCFQSPI_IOSIZE 0x40
......
......@@ -30,22 +30,17 @@
#if defined(CONFIG_SPI_COLDFIRE_QSPI) || defined(CONFIG_SPI_COLDFIRE_QSPI_MODULE)
static struct resource m528x_qspi_resources[] = {
{
.start = MCFQSPI_IOBASE,
.end = MCFQSPI_IOBASE + MCFQSPI_IOSIZE - 1,
.start = MCFQSPI_BASE,
.end = MCFQSPI_BASE + MCFQSPI_SIZE - 1,
.flags = IORESOURCE_MEM,
},
{
.start = MCFINT_VECBASE + MCFINT_QSPI,
.end = MCFINT_VECBASE + MCFINT_QSPI,
.start = MCF_IRQ_QSPI,
.end = MCF_IRQ_QSPI,
.flags = IORESOURCE_IRQ,
},
};
#define MCFQSPI_CS0 147
#define MCFQSPI_CS1 148
#define MCFQSPI_CS2 149
#define MCFQSPI_CS3 150
static int m528x_cs_setup(struct mcfqspi_cs_control *cs_control)
{
int status;
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment