Commit 3e88a579 authored by Richard Purdie's avatar Richard Purdie Committed by Russell King

[ARM] 2861/1: PXA: Add some extra pxa27x register definitions

Patch from Richard Purdie

Add some extra pxa27x register definitions needed for the Sharp
SL-C3000 (Spitz).
Signed-off-by: default avatarRichard Purdie <rpurdie@rpsys.net>
Signed-off-by: default avatarRussell King <rmk+kernel@arm.linux.org.uk>
parent cb85a502
......@@ -818,6 +818,23 @@
#define UDCOTGICR_IEIDF (1 << 0) /* OTG ID Change Falling Edge
Interrupt Enable */
#define UP2OCR __REG(0x40600020) /* USB Port 2 Output Control register */
#define UP2OCR_CPVEN (1 << 0) /* Charge Pump Vbus Enable */
#define UP2OCR_CPVPE (1 << 1) /* Charge Pump Vbus Pulse Enable */
#define UP2OCR_DPPDE (1 << 2) /* Host Port 2 Transceiver D+ Pull Down Enable */
#define UP2OCR_DMPDE (1 << 3) /* Host Port 2 Transceiver D- Pull Down Enable */
#define UP2OCR_DPPUE (1 << 4) /* Host Port 2 Transceiver D+ Pull Up Enable */
#define UP2OCR_DMPUE (1 << 5) /* Host Port 2 Transceiver D- Pull Up Enable */
#define UP2OCR_DPPUBE (1 << 6) /* Host Port 2 Transceiver D+ Pull Up Bypass Enable */
#define UP2OCR_DMPUBE (1 << 7) /* Host Port 2 Transceiver D- Pull Up Bypass Enable */
#define UP2OCR_EXSP (1 << 8) /* External Transceiver Speed Control */
#define UP2OCR_EXSUS (1 << 9) /* External Transceiver Speed Enable */
#define UP2OCR_IDON (1 << 10) /* OTG ID Read Enable */
#define UP2OCR_HXS (1 << 16) /* Host Port 2 Transceiver Output Select */
#define UP2OCR_HXOE (1 << 17) /* Host Port 2 Transceiver Output Enable */
#define UP2OCR_SEOS (1 << 24) /* Single-Ended Output Select */
#define UDCCSN(x) __REG2(0x40600100, (x) << 2)
#define UDCCSR0 __REG(0x40600100) /* UDC Control/Status register - Endpoint 0 */
#define UDCCSR0_SA (1 << 7) /* Setup Active */
......@@ -1423,6 +1440,7 @@
#define GPIO84_NSSP_RX (84 | GPIO_ALT_FN_2_IN)
#define GPIO85_nPCE_1_MD (85 | GPIO_ALT_FN_1_OUT)
#define GPIO92_MMCDAT0_MD (92 | GPIO_ALT_FN_1_OUT)
#define GPIO104_pSKTSEL_MD (104 | GPIO_ALT_FN_1_OUT)
#define GPIO109_MMCDAT1_MD (109 | GPIO_ALT_FN_1_OUT)
#define GPIO110_MMCDAT2_MD (110 | GPIO_ALT_FN_1_OUT)
#define GPIO110_MMCCS0_MD (110 | GPIO_ALT_FN_1_OUT)
......@@ -1510,6 +1528,8 @@
#define PSSR_BFS (1 << 1) /* Battery Fault Status */
#define PSSR_SSS (1 << 0) /* Software Sleep Status */
#define PSLR_SL_ROD (1 << 20) /* Sleep-Mode/Depp-Sleep Mode nRESET_OUT Disable */
#define PCFR_RO (1 << 15) /* RDH Override */
#define PCFR_PO (1 << 14) /* PH Override */
#define PCFR_GPROD (1 << 12) /* GPIO nRESET_OUT Disable */
......@@ -1517,6 +1537,7 @@
#define PCFR_FVC (1 << 10) /* Frequency/Voltage Change */
#define PCFR_DC_EN (1 << 7) /* Sleep/deep-sleep DC-DC Converter Enable */
#define PCFR_PI2CEN (1 << 6) /* Enable PI2C controller */
#define PCFR_GPR_EN (1 << 4) /* nRESET_GPIO Pin Enable */
#define PCFR_DS (1 << 3) /* Deep Sleep Mode */
#define PCFR_FS (1 << 2) /* Float Static Chip Selects */
#define PCFR_FP (1 << 1) /* Float PCMCIA controls */
......@@ -1810,6 +1831,11 @@
#define LCCR0_PDD_S 12
#define LCCR0_BM (1 << 20) /* Branch mask */
#define LCCR0_OUM (1 << 21) /* Output FIFO underrun mask */
#define LCCR0_LCDT (1 << 22) /* LCD panel type */
#define LCCR0_RDSTM (1 << 23) /* Read status interrupt mask */
#define LCCR0_CMDIM (1 << 24) /* Command interrupt mask */
#define LCCR0_OUC (1 << 25) /* Overlay Underlay control bit */
#define LCCR0_LDDALT (1 << 26) /* LDD alternate mapping control */
#define LCCR1_PPL Fld (10, 0) /* Pixels Per Line - 1 */
#define LCCR1_DisWdth(Pixel) /* Display Width [1..800 pix.] */ \
......@@ -2062,7 +2088,10 @@
#define UHCFMN __REG(0x4C00003C) /* UHC Frame Number */
#define UHCPERS __REG(0x4C000040) /* UHC Periodic Start */
#define UHCLS __REG(0x4C000044) /* UHC Low Speed Threshold */
#define UHCRHDA __REG(0x4C000048) /* UHC Root Hub Descriptor A */
#define UHCRHDA_NOCP (1 << 12) /* No over current protection */
#define UHCRHDB __REG(0x4C00004C) /* UHC Root Hub Descriptor B */
#define UHCRHS __REG(0x4C000050) /* UHC Root Hub Status */
#define UHCRHPS1 __REG(0x4C000054) /* UHC Root Hub Port 1 Status */
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment