hpsa: add masked physical devices into h->dev[] array

Cache the ioaccel handle so that when we need to abort commands sent
down the ioaccel2 path, we can look up the LUN ID in h->dev[] instead of
having to do I/O to the controller.

Add a field to elements in h->dev[] to keep track of how the device is exposed
to the SCSI mid layer: Not at all, without an upper level driver
(no_uld_attach) or normally exposed.

Since masked physical devices are now present in h->dev[] array
it would be perfectly possible to do

	echo scsi add-single-device 2 2 0 0 > /proc/scsi/scsi

and bring them online.  This was previously not allowed for masked
physical devices.

Ensure that the mapping of physical disks to logical drives gets updated in a
consistent way when a RAID migration occurs and is not touched until updates
to it are complete.

now instead of doing CISS_REPORT_PHYSICAL to get the LUNID for
the physical disk in hpsa_get_pdisk_of_ioaccel2(), just get
it out of h->dev[] where we already have it cached.

do not touch phys_disk[] for ioaccel enabled logical drives during rescan
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@Suse.de>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>

drivers/scsi/hpsa.h

@@ -54,6 +54,7 @@ struct hpsa_scsi_dev_t {
 	u32 ioaccel_handle;
 	int offload_config;		/* I/O accel RAID offload configured */
 	int offload_enabled;		/* I/O accel RAID offload enabled */
+	int offload_to_be_enabled;
 	int offload_to_mirror;		/* Send next I/O accelerator RAID
 					 * offload request to mirror drive
 					 */
@@ -68,6 +69,11 @@ struct hpsa_scsi_dev_t {
 	 * devices in order to honor physical device queue depth limits.
 	 */
 	struct hpsa_scsi_dev_t *phys_disk[RAID_MAP_MAX_ENTRIES];
+#define HPSA_DO_NOT_EXPOSE	0x0
+#define HPSA_SG_ATTACH		0x1
+#define HPSA_ULD_ATTACH		0x2
+#define HPSA_SCSI_ADD		(HPSA_SG_ATTACH | HPSA_ULD_ATTACH)
+	u8 expose_state;
 };
 
 struct reply_queue_buffer {

drivers/scsi/hpsa_cmd.h

@@ -240,6 +240,7 @@ struct ReportLUNdata {
 
 struct ext_report_lun_entry {
 	u8 lunid[8];
+#define MASKED_DEVICE(x) ((x)[3] & 0xC0)
 #define GET_BMIC_BUS(lunid) ((lunid)[7] & 0x3F)
 #define GET_BMIC_LEVEL_TWO_TARGET(lunid) ((lunid)[6])
 #define GET_BMIC_DRIVE_NUMBER(lunid) (((GET_BMIC_BUS((lunid)) - 1) << 8) + \
@@ -247,6 +248,8 @@ struct ext_report_lun_entry {
 	u8 wwid[8];
 	u8 device_type;
 	u8 device_flags;
+#define NON_DISK_PHYS_DEV(x) ((x)[17] & 0x01)
+#define PHYS_IOACCEL(x) ((x)[17] & 0x08)
 	u8 lun_count; /* multi-lun device, how many luns */
 	u8 redundant_paths;
 	u32 ioaccel_handle; /* ioaccel1 only uses lower 16 bits */