Manual merge of drivers/net/*/Kconfig changes.

Documentation/networking/sk98lin.txt

@@ -2,9 +2,9 @@
 All rights reserved
 ===========================================================================
 
-sk98lin.txt created 18-Jul-2003
+sk98lin.txt created 23-Sep-2003
 
-Readme File for sk98lin v6.14
+Readme File for sk98lin v6.18
 Marvell Yukon/SysKonnect SK-98xx Gigabit Ethernet Adapter family driver for LINUX
 
 This file contains
@@ -19,7 +19,6 @@ This file contains
  5  Large Frame Support
  6  VLAN and Link Aggregation Support (IEEE 802.1, 802.1q, 802.3ad)
  7  Troubleshooting
- 8  History
 
 ===========================================================================
 
@@ -76,8 +75,8 @@ follows:
 To integrate the driver permanently into the kernel, proceed as follows:
 
 1. Select the menu "Network device support" and then "Ethernet(1000Mbit)"
-2. Mark "Marvell Yukon/SysKonnect SK-98xx/SK-95xx Gigabit Ethernet Adapter 
-   support" with (*) 
+2. Mark "Marvell Yukon Chipset / SysKonnect SK-98xx family support" 
+   with (*) 
 3. Build a new kernel when the configuration of the above options is 
    finished.
 4. Install the new kernel.
@@ -88,8 +87,8 @@ To use the driver as a module, proceed as follows:
 1. Enable 'loadable module support' in the kernel.
 2. For automatic driver start, enable the 'Kernel module loader'.
 3. Select the menu "Network device support" and then "Ethernet(1000Mbit)"
-4. Mark "Marvell Yukon/SysKonnect SK-98xx/SK-95xx Gigabit Ethernet Adapter 
-   support" with (M)
+4. Mark "Marvell Yukon Chipset / SysKonnect SK-98xx family support" 
+   with (M)
 5. Execute the command "make modules".
 6. Execute the command "make modules_install".
    The appropiate modules will be installed.
@@ -201,7 +200,7 @@ You also want to set DuplexCapabilities on the first adapter
 to FULL, and on the second adapter to HALF.
 Then, you must enter:
 
-        modprobe sk98lin AutoNeg=On,Off DupCap=Full,Half
+        modprobe sk98lin AutoNeg_A=On,Off DupCap_A=Full,Half
 
 NOTE: The number of adapters that can be configured this way is
       limited in the driver (file skge.c, constant SK_MAX_CARD_PARAM).
@@ -259,9 +258,9 @@ This parameter can be used to set the flow control capabilities the
 port reports during auto-negotiation. It can be set for each port 
 individually.
 Possible modes:
-   -- Sym      = Symetric: both link partners are allowed to send 
+   -- Sym      = Symmetric: both link partners are allowed to send 
                   PAUSE frames
-   -- SymOrRem = SymetricOrRemote: both or only remote partner 
+   -- SymOrRem = SymmetricOrRemote: both or only remote partner 
                   are allowed to send PAUSE frames
    -- LocSend  = LocalSend: only local link partner is allowed 
                   to send PAUSE frames
@@ -286,7 +285,7 @@ with this parameter.
 4.2  Adapter Parameters
 -----------------------
 
-Connection Type
+Connection Type (SK-98xx V2.0 copper adapters only)
 ---------------
 Parameter:    ConType
 Values:       Auto, 100FD, 100HD, 10FD, 10HD
@@ -546,7 +545,7 @@ Problem:  Upon driver start, the following error message is displayed:
           Nr:    0xcc
           Msg:   SkGeInitPort() cannot init running ports"
 Reason:   You are using a driver compiled for single processor machines 
-          on a multiprocessor machine with SMP (Symetric MultiProcessor) 
+          on a multiprocessor machine with SMP (Symmetric MultiProcessor) 
           kernel.
 Solution: Configure your kernel appropriately and recompile the kernel or
           the modules.
@@ -564,216 +563,6 @@ information is available:
 - Driver version
 ***
 
-8  History
-==========
-
-VERSION 6.14
-New Features:
-- None
-Problems fixed: 
-- Fix: memory leak when sending short padded frames 
-- Fix: helptext for menuconfig in kernel 2.6 updated
-- Fix: PNMI_READ defines retrieve correct amount of bytes
-Known limitations:
-- None
-
-VERSION 6.13
-New Features:
-- New parameter ConType combining different per-port parameters
-Problems fixed:
-- Fix: change of MTU-size without warning (bugreport #10721)
-- Fix: HW checksumming when Kernel 2.5/2.6 corrected
-- Fix: Padding of small packets (<60 bytes) not 0xaa, but 0x00 instead
-- Fix: Minor edits corrected 
-- Fix: Obsolete function SetQueueSize() removed
-- Fix: Removed proprietary defines - used defines from skgehw.h instead
-Known limitations:
-- None
-
-VERSION 6.12
-New Features:
-- enabling/disabling checksum
-Problems fixed:
-- Fix: KLM load/unload using new refcount interface for Kernel 2.5/2.6
-Known limitations:
-- None
-
-VERSION 6.11 (In-Kernel version)
-New Features:
-- Support for Kernel 2.5/2.6
-- Support for new IO-control MIB data structure
-- New SkOsGetTime function
-Problems fixed:
-- Fix: Race condition with broken LM80 chip
-- Fix: Common modules update (#10803, #10768, #10767)
-- Fix: Dim, ProcFS, Isr, Module Support changes for Kernel 2.5/2.6
-Known limitations:
-- None
-
-VERSION 6.10
-New Features:
-- none
-Problems fixed:
-- Fix: Race condition with padded frames
-Known limitations:
-- None
-
-VERSION 6.09
-New Features:
-- none
-Problems fixed:
-- Fix: Disabled HW Error IRQ on 32-bit Yukon if sensor IRQ occurs
-- Fix: Delay race condition with some server machines
-Known limitations:
-- None
-
-VERSION 6.08
-New Features:
-- Add: Dynamic Interrupt moderation
-- Add: Blink mode verification
-- Fix: CSUM changes
-Problems fixed:
-- Fix: CSUM changes
-Known limitations:
-- None
-
-VERSION 6.04 - 6.07
-New Features:
-- Common modules update
-Problems fixed:
-- none
-Known limitations:
-- None
-
-VERSION 6.03
-New Features:
-- Common modules update
-Problems fixed:
-- Remove useless init_module/cleanup_module forward declarations
-Known limitations:
-- None
-
-VERSION 6.02 (In-Kernel version)
-New Features:
-- Common modules update
-Problems fixed:
-- Boot message cleanup
-Known limitations:
-- None
-
-VERSION 6.00 (In-Kernel version)
-New Features:
-- Support for SK-98xx V2.0 adapters
-- Support for gmac
-- Support for kernel 2.4.x and kernel 2.2.x
-- Zerocopy support for kernel 2.4.x with sendfile()
-- Support for scatter-gather functionality with sendfile()
-- Speed support for SK-98xx V2.0 adapters
-- New ProcFs entries
-- New module parameters
-Problems fixed:
-- ProcFS initialization
-- csum packet error
-- Ierror/crc counter error (#10767)
-- rx_too_long counter error (#10751)
-Known limitations:
-- None
-
-VERSION 4.11
-New Features:
-- none
-Problems fixed:
-- Error statistic counter fix (#10620)
-- RLMT-Fixes (#10659, #10639, #10650)
-- LM80 sensor initialization fix (#10623)
-- SK-CSUM memory fixes (#10610).
-Known limitations:
-- None
-
-VERSION 4.10
-New Features:
-- New ProcFs entries
-Problems fixed:
-- Corrected some printk's
-Known limitations:
-- None
-
-VERSION 4.09
-New Features:
-- IFF_RUNNING support (link status)
-- New ProcFs entries
-Problems fixed:
-- too long counters
-- too short counters
-- Kernel error compilation
-Known limitations:
-- None
- 
-VERSION 4.06 (In-Kernel version)
-Problems fixed:
-- MTU init problems
- 
-VERSION 4.04
-Problems fixed:
-- removed VLAN error messages
-
-VERSION 4.02 (In-Kernel version)
-New Features:
-- Add Kernel 2.4 changes
-Known limitations:
-- None
-
-VERSION 4.01 (In-Kernel version)
-Problems fixed:
-- Full statistics support for DualNet mode
-Known limitations:
-- None
-
-VERSION 4.00 (In-Kernel version)
-Problems fixed:
-- Memory leak found 
-New Features:
-- Proc filesystem integration
-- DualNet functionality integrated
-- Rlmt networks added
-Known limitations:
-- statistics partially incorrect in DualNet mode
-
-VERSION 3.04 (In-Kernel version)
-Problems fixed:
-- Driver start failed on UltraSPARC
-- Rx checksum calculation for big endian machines did not work
-- Jumbo frames were counted as input-errors in netstat
-
-VERSION 3.03 (Standalone version)
-Problems fixed:
-- Compilation did not find script "printver.sh" if "." not in PATH
-Known limitations:
-- None
-
-VERSION 3.02 (In-Kernel version)
-Problems fixed:
-- None
-New Features:
-- Integration in Linux kernel source (2.2.14 and 2.3.29) 
-Known limitations:
-- None
-
-VERSION 3.01
-Problems fixed:
-- None
-New Features:
-- Full source release
-Known limitations:
-- None
-
-VERSION 3.00
-Problems fixed:
-- None
-New Features:
-- Support for 1000Base-T adapters (SK-9821 and SK-9822)
-Known limitations:
-- None
 
 
 ***End of Readme File***

drivers/net/Kconfig

@@ -1891,18 +1891,23 @@ config SK98LIN
 	  by this driver:
 	    - 3Com 3C940 Gigabit LOM Ethernet Adapter
 	    - 3Com 3C941 Gigabit LOM Ethernet Adapter
-	    - Allied Telesyn AT-2970SX Gigabit Ethernet Adapter
 	    - Allied Telesyn AT-2970LX Gigabit Ethernet Adapter
+	    - Allied Telesyn AT-2970LX/2SC Gigabit Ethernet Adapter
+	    - Allied Telesyn AT-2970SX Gigabit Ethernet Adapter
+	    - Allied Telesyn AT-2970SX/2SC Gigabit Ethernet Adapter
 	    - Allied Telesyn AT-2970TX Gigabit Ethernet Adapter
+	    - Allied Telesyn AT-2970TX/2TX Gigabit Ethernet Adapter
 	    - Allied Telesyn AT-2971SX Gigabit Ethernet Adapter
 	    - Allied Telesyn AT-2971T Gigabit Ethernet Adapter
-	    - Allied Telesyn AT-2970SX/2SC Gigabit Ethernet Adapter
-	    - Allied Telesyn AT-2970LX/2SC Gigabit Ethernet Adapter
-	    - Allied Telesyn AT-2970TX/2TX Gigabit Ethernet Adapter
-	    - N-Way PCI-Bus Giga-Card 1000/100/10Mbps(L)
 	    - DGE-530T Gigabit Ethernet Adapter
 	    - EG1032 v2 Instant Gigabit Network Adapter
 	    - EG1064 v2 Instant Gigabit Network Adapter
+	    - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Abit)
+	    - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Asus)
+	    - Marvell 88E8001 Gigabit LOM Ethernet Adapter (ECS)
+	    - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Epox)
+	    - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Gigabyte)
+	    - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Iwill)
 	    - Marvell RDK-8001 Adapter
 	    - Marvell RDK-8002 Adapter
 	    - Marvell RDK-8003 Adapter
@@ -1911,27 +1916,31 @@ config SK98LIN
 	    - Marvell RDK-8007 Adapter
 	    - Marvell RDK-8008 Adapter
 	    - Marvell RDK-8009 Adapter
+	    - Marvell RDK-8010 Adapter
 	    - Marvell RDK-8011 Adapter
 	    - Marvell RDK-8012 Adapter
-	    - Marvell Yukon Gigabit Ethernet 10/100/1000Base-T Adapter
+	    - Marvell Yukon Gigabit Ethernet 10/100/1000Base-T Adapter (32 bit)
+	    - Marvell Yukon Gigabit Ethernet 10/100/1000Base-T Adapter (64 bit)
+	    - N-Way PCI-Bus Giga-Card 1000/100/10Mbps(L)
+	    - SK-9521 10/100/1000Base-T Adapter
+	    - SK-9521 V2.0 10/100/1000Base-T Adapter
 	    - SK-9821 Gigabit Ethernet Server Adapter (SK-NET GE-T)
+	    - SK-9821 V2.0 Gigabit Ethernet 10/100/1000Base-T Adapter
 	    - SK-9822 Gigabit Ethernet Server Adapter (SK-NET GE-T dual link)
 	    - SK-9841 Gigabit Ethernet Server Adapter (SK-NET GE-LX)
+	    - SK-9841 V2.0 Gigabit Ethernet 1000Base-LX Adapter
 	    - SK-9842 Gigabit Ethernet Server Adapter (SK-NET GE-LX dual link)
 	    - SK-9843 Gigabit Ethernet Server Adapter (SK-NET GE-SX)
+	    - SK-9843 V2.0 Gigabit Ethernet 1000Base-SX Adapter
 	    - SK-9844 Gigabit Ethernet Server Adapter (SK-NET GE-SX dual link)
+	    - SK-9851 V2.0 Gigabit Ethernet 1000Base-SX Adapter
 	    - SK-9861 Gigabit Ethernet Server Adapter (SK-NET GE-SX Volition)
+	    - SK-9861 V2.0 Gigabit Ethernet 1000Base-SX Adapter
 	    - SK-9862 Gigabit Ethernet Server Adapter (SK-NET GE-SX Volition dual link)
 	    - SK-9871 Gigabit Ethernet Server Adapter (SK-NET GE-ZX)
-	    - SK-9872 Gigabit Ethernet Server Adapter (SK-NET GE-ZX dual link)
-	    - SK-9521 V2.0 10/100/1000Base-T Adapter
-	    - SK-9821 V2.0 Gigabit Ethernet 10/100/1000Base-T Adapter
-	    - SK-9841 V2.0 Gigabit Ethernet 1000Base-LX Adapter
-	    - SK-9843 V2.0 Gigabit Ethernet 1000Base-SX Adapter
-	    - SK-9851 V2.0 Gigabit Ethernet 1000Base-SX Adapter
-	    - SK-9861 V2.0 Gigabit Ethernet 1000Base-SX Adapter
 	    - SK-9871 V2.0 Gigabit Ethernet 1000Base-ZX Adapter
-	    - SK-9521 10/100/1000Base-T Adapter
+	    - SK-9872 Gigabit Ethernet Server Adapter (SK-NET GE-ZX dual link)
+	    - SMC EZ Card 1000 (SMC9452TXV.2)
 	  
 	  The adapters support Jumbo Frames.
 	  The dual link adapters support link-failover and dual port features.
@@ -1941,145 +1950,10 @@ config SK98LIN
 	  optional driver parameters.
 	  Questions concerning this driver may be addressed to:
 	      linux@syskonnect.de
-
+	  
 	  To compile this driver as a module, choose M here: the module
 	  will be called sk98lin.  This is recommended.
 
-config CONFIG_SK98LIN_T1
-	bool "3Com 3C940/3C941 Gigabit Ethernet Adapter"
-	depends on SK98LIN
-	help
-	  This driver supports:
-	  
-	    - 3Com 3C940 Gigabit LOM Ethernet Adapter
-	    - 3Com 3C941 Gigabit LOM Ethernet Adapter
-	
-	  Questions concerning this driver may be addressed to:
-	      linux@syskonnect.de
-	
-config CONFIG_SK98LIN_T2
-	bool "Allied Telesyn AT-29xx Gigabit Ethernet Adapter"
-	depends on SK98LIN
-	help
-	  This driver supports:
-	  
-	    - Allied Telesyn AT-2970SX Gigabit Ethernet Adapter
-	    - Allied Telesyn AT-2970LX Gigabit Ethernet Adapter
-	    - Allied Telesyn AT-2970TX Gigabit Ethernet Adapter
-	    - Allied Telesyn AT-2971SX Gigabit Ethernet Adapter
-	    - Allied Telesyn AT-2971T Gigabit Ethernet Adapter
-	    - Allied Telesyn AT-2970SX/2SC Gigabit Ethernet Adapter
-	    - Allied Telesyn AT-2970LX/2SC Gigabit Ethernet Adapter
-	    - Allied Telesyn AT-2970TX/2TX Gigabit Ethernet Adapter
-	
-	  Questions concerning this driver may be addressed to:
-	      linux@syskonnect.de
-	
-config CONFIG_SK98LIN_T3
-	bool "CNet N-Way Gigabit Ethernet Adapter"
-	depends on SK98LIN
-	help
-	  This driver supports:
-	  
-	    - N-Way PCI-Bus Giga-Card 1000/100/10Mbps(L)
-	
-	  Questions concerning this driver may be addressed to:
-	      linux@syskonnect.de
-	
-config CONFIG_SK98LIN_T4
-	bool "D-Link DGE-530T Gigabit Ethernet Adapter"
-	depends on SK98LIN
-	help
-	  This driver supports:
-	  
-	    - DGE-530T Gigabit Ethernet Adapter
-	
-	  Questions concerning this driver may be addressed to:
-	      linux@syskonnect.de
-	
-config CONFIG_SK98LIN_T5
-	bool "Linksys EG10xx Ethernet Server Adapter"
-	depends on SK98LIN
-	help
-	  This driver supports:
-	  
-	    - EG1032 v2 Instant Gigabit Network Adapter
-	    - EG1064 v2 Instant Gigabit Network Adapter
-	
-	  Questions concerning this driver may be addressed to:
-	      linux@syskonnect.de
-	
-config CONFIG_SK98LIN_T6
-	bool "Marvell RDK-80xx Adapter"
-	depends on SK98LIN
-	help
-	  This driver supports:
-	  
-	    - Marvell RDK-8001 Adapter
-	    - Marvell RDK-8002 Adapter
-	    - Marvell RDK-8003 Adapter
-	    - Marvell RDK-8004 Adapter
-	    - Marvell RDK-8006 Adapter
-	    - Marvell RDK-8007 Adapter
-	    - Marvell RDK-8008 Adapter
-	    - Marvell RDK-8009 Adapter
-	    - Marvell RDK-8011 Adapter
-	    - Marvell RDK-8012 Adapter
-	
-	  Questions concerning this driver may be addressed to:
-	      linux@syskonnect.de
-	
-config CONFIG_SK98LIN_T7
-	bool "Marvell Yukon Gigabit Ethernet Adapter"
-	depends on SK98LIN
-	help
-	  This driver supports:
-	  
-	    - Marvell Yukon Gigabit Ethernet 10/100/1000Base-T Adapter
-	
-	  Questions concerning this driver may be addressed to:
-	      linux@syskonnect.de
-	
-config CONFIG_SK98LIN_T8
-	bool "SysKonnect SK-98xx Server Gigabit Adapter"
-	depends on SK98LIN
-	help
-	  This driver supports:
-	  
-	    - SK-9821 Gigabit Ethernet Server Adapter (SK-NET GE-T)
-	    - SK-9822 Gigabit Ethernet Server Adapter (SK-NET GE-T dual link)
-	    - SK-9841 Gigabit Ethernet Server Adapter (SK-NET GE-LX)
-	    - SK-9842 Gigabit Ethernet Server Adapter (SK-NET GE-LX dual link)
-	    - SK-9843 Gigabit Ethernet Server Adapter (SK-NET GE-SX)
-	    - SK-9844 Gigabit Ethernet Server Adapter (SK-NET GE-SX dual link)
-	    - SK-9861 Gigabit Ethernet Server Adapter (SK-NET GE-SX Volition)
-	    - SK-9862 Gigabit Ethernet Server Adapter (SK-NET GE-SX Volition dual link)
-	    - SK-9871 Gigabit Ethernet Server Adapter (SK-NET GE-ZX)
-	    - SK-9872 Gigabit Ethernet Server Adapter (SK-NET GE-ZX dual link)
-	
-	  Questions concerning this driver may be addressed to:
-	      linux@syskonnect.de
-	
-config CONFIG_SK98LIN_T9
-	bool "SysKonnect SK-98xx V2.0 Gigabit Ethernet Adapter"
-	depends on SK98LIN
-	help
-	  This driver supports:
-	  
-	    - SK-9521 V2.0 10/100/1000Base-T Adapter
-	    - SK-9821 V2.0 Gigabit Ethernet 10/100/1000Base-T Adapter
-	    - SK-9841 V2.0 Gigabit Ethernet 1000Base-LX Adapter
-	    - SK-9843 V2.0 Gigabit Ethernet 1000Base-SX Adapter
-	    - SK-9851 V2.0 Gigabit Ethernet 1000Base-SX Adapter
-	    - SK-9861 V2.0 Gigabit Ethernet 1000Base-SX Adapter
-	    - SK-9871 V2.0 Gigabit Ethernet 1000Base-ZX Adapter
-	    - SK-9521 10/100/1000Base-T Adapter
-	  
-	  Questions concerning this driver may be addressed to:
-	      linux@syskonnect.de
-	  
-
-
 config TIGON3
 	tristate "Broadcom Tigon3 support"
 	depends on PCI

drivers/net/arcnet/Kconfig

@@ -21,11 +21,9 @@ config ARCNET
 	  from <http://www.tldp.org/docs.html#howto>(even though ARCnet
 	  is not really Ethernet).
 
-	  This driver is also available as a module ( = code which can be
-	  inserted in and removed from the running kernel whenever you want).
-	  The module will be called arcnet.  If you want to compile it as a
-	  module, say M here and read <file:Documentation/modules.txt> as well
-	  as <file:Documentation/networking/net-modules.txt>.
+	  To compile this driver as a module, choose M here and read
+	  <file:Documentation/networking/net-modules.txt>.  The module will
+	  be called arcnet.
 
 config ARCNET_1201
 	tristate "Enable standard ARCNet packet format (RFC 1201)"
@@ -69,11 +67,9 @@ config ARCNET_COM90xx
 	  have always used the old ARCnet driver without knowing what type of
 	  card you had, this is probably the one for you.
 
-	  This driver is also available as a module ( = code which can be
-	  inserted in and removed from the running kernel whenever you want).
-	  The module will be called com90xx.  If you want to compile it as a
-	  module, say M here and read <file:Documentation/modules.txt> as well
-	  as <file:Documentation/networking/net-modules.txt>.
+	  To compile this driver as a module, choose M here and read
+	  <file:Documentation/networking/net-modules.txt>.  The module will
+	  be called com90xx.
 
 config ARCNET_COM90xxIO
 	tristate "ARCnet COM90xx (IO mapped) chipset driver"
@@ -84,11 +80,9 @@ config ARCNET_COM90xxIO
 	  the normal driver. Only use it if your card doesn't support shared
 	  memory.
 
-	  This driver is also available as a module ( = code which can be
-	  inserted in and removed from the running kernel whenever you want).
-	  The module will be called com90io.  If you want to compile it as a
-	  module, say M here and read <file:Documentation/modules.txt> as well
-	  as <file:Documentation/networking/net-modules.txt>.
+	  To compile this driver as a module, choose M here and read
+	  <file:Documentation/networking/net-modules.txt>.  The module will
+	  be called com90io.
 
 config ARCNET_RIM_I
 	tristate "ARCnet COM90xx (RIM I) chipset driver"
@@ -99,11 +93,9 @@ config ARCNET_RIM_I
 	  driver is completely untested, so if you have one of these cards,
 	  please mail dwmw2@infradead.org, especially if it works!
 
-	  This driver is also available as a module ( = code which can be
-	  inserted in and removed from the running kernel whenever you
-	  want). The module will be called arc-rimi.  If you want to compile
-	  it as a module, say M here and read <file:Documentation/modules.txt>
-	  as  well as <file:Documentation/networking/net-modules.txt>.
+	  To compile this driver as a module, choose M here and read
+	  <file:Documentation/networking/net-modules.txt>.  The module will
+	  be called arc-rimi.
 
 config ARCNET_COM20020
 	tristate "ARCnet COM20020 chipset driver"
@@ -113,11 +105,9 @@ config ARCNET_COM20020
 	  things as promiscuous mode, so packet sniffing is possible, and
 	  extra diagnostic information.
 
-	  This driver is also available as a module ( = code which can be
-	  inserted in and removed from the running kernel whenever you want).
-	  The module will be called com20020.  If you want to compile it as
-	  a module, say M here and read <file:Documentation/modules.txt> as
-	  well as <file:Documentation/networking/net-modules.txt>.
+	  To compile this driver as a module, choose M here and read
+	  <file:Documentation/networking/net-modules.txt>.  The module will
+	  be called com20020.
 
 config ARCNET_COM20020_ISA
 	tristate "Support for COM20020 on ISA"

drivers/net/sk98lin/h/skdrv1st.h

@@ -2,8 +2,8 @@
  *
  * Name:	skdrv1st.h
  * Project:	GEnesis, PCI Gigabit Ethernet Adapter
- * Version:	$Revision: 1.15 $
- * Date:	$Date: 2003/07/17 14:54:09 $
+ * Version:	$Revision: 1.1 $
+ * Date:	$Date: 2003/07/21 07:22:43 $
  * Purpose:	First header file for driver and all other modules
  *
  ******************************************************************************/
@@ -26,6 +26,9 @@
  * History:
  *
  *	$Log: skdrv1st.h,v $
+ *	Revision 1.1  2003/07/21 07:22:43  rroesler
+ *	Fix: Re-Enter after CVS crash
+ *	
  *	Revision 1.15  2003/07/17 14:54:09  rroesler
  *	Fix: Corrected SK_PNMI_READ macros to copy right amount of bytes
  *	

drivers/net/sk98lin/h/skdrv2nd.h

@@ -2,8 +2,8 @@
  *
  * Name:	skdrv2nd.h
  * Project:	GEnesis, PCI Gigabit Ethernet Adapter
- * Version:	$Revision: 1.19 $
- * Date:	$Date: 2003/07/07 09:53:10 $
+ * Version:	$Revision: 1.3 $
+ * Date:	$Date: 2003/08/12 16:51:18 $
  * Purpose:	Second header file for driver and all other modules
  *
  ******************************************************************************/
@@ -26,6 +26,16 @@
  * History:
  *
  *	$Log: skdrv2nd.h,v $
+ *	Revision 1.3  2003/08/12 16:51:18  mlindner
+ *	Fix: UDP and TCP Proto checks
+ *	Fix: UDP header offset
+ *	
+ *	Revision 1.2  2003/08/07 10:50:54  mlindner
+ *	Add: Speed and HW-Csum support for Yukon Lite chipset
+ *	
+ *	Revision 1.1  2003/07/21 07:25:29  rroesler
+ *	Fix: Re-Enter after CVS crash
+ *	
  *	Revision 1.19  2003/07/07 09:53:10  rroesler
  *	Fix: Removed proprietary RxTx defines and used the ones from skgehw.h instead
  *	
@@ -315,12 +325,13 @@ struct s_IOCTL {
 #define C_OFFSET_IPHEADER               C_LEN_ETHERMAC_HEADER
 #define C_OFFSET_IPHEADER_IPPROTO       9
 #define C_OFFSET_TCPHEADER_TCPCS        16
+#define C_OFFSET_UDPHEADER_UDPCS        6
 
 #define C_OFFSET_IPPROTO                ( (C_LEN_ETHERMAC_HEADER) + \
                                           (C_OFFSET_IPHEADER_IPPROTO) )
 
-#define C_PROTO_ID_UDP                  6       /* refer to RFC 790 or Stevens'   */
-#define C_PROTO_ID_TCP                  17      /* TCP/IP illustrated for details */
+#define C_PROTO_ID_UDP                  17       /* refer to RFC 790 or Stevens'   */
+#define C_PROTO_ID_TCP                  6        /* TCP/IP illustrated for details */
 
 /* TX and RX descriptors *****************************************************/
 
@@ -390,6 +401,7 @@ struct s_TxD {
 typedef struct s_DevNet DEV_NET;
 
 struct s_DevNet {
+	struct			proc_dir_entry *proc;
 	int             PortNr;
 	int             NetNr;
 	int             Mtu;
@@ -550,6 +562,10 @@ struct s_AC  {
 	/* Only for tests */
 	int		PortUp;
 	int		PortDown;
+	int		ChipsetType;	/*  Chipset family type 
+							 *  0 == Genesis family support
+							 *  1 == Yukon family support
+							 */
 };
 
 

drivers/net/sk98lin/h/skgeinit.h

@@ -722,15 +722,14 @@ typedef	struct s_GeInit {
 /*
  * Error numbers and messages for skxmac2.c and skgeinit.c
  */
-
 #define SKERR_HWI_E001		(SK_ERRBASE_HWINIT)
-#define SKERR_HWI_E001MSG	"SkXmClrExactAddr() has got invalid parameters"
+#define SKERR_HWI_E001MSG	"SkXmClrExactAddr() has got illegal parameters"
 #define SKERR_HWI_E002		(SKERR_HWI_E001+1)
 #define SKERR_HWI_E002MSG	"SkGeInit(): Level 1 call missing"
 #define SKERR_HWI_E003		(SKERR_HWI_E002+1)
-#define SKERR_HWI_E003MSG	"SkGeInit() called with invalid init Level"
+#define SKERR_HWI_E003MSG	"SkGeInit() called with illegal init Level"
 #define SKERR_HWI_E004		(SKERR_HWI_E003+1)
-#define SKERR_HWI_E004MSG	"SkGeInitPort(): Queue Size invalid configured"
+#define SKERR_HWI_E004MSG	"SkGeInitPort(): Queue Size illegal configured"
 #define SKERR_HWI_E005		(SKERR_HWI_E004+1)
 #define SKERR_HWI_E005MSG	"SkGeInitPort(): cannot init running ports"
 #define SKERR_HWI_E006		(SKERR_HWI_E005+1)
@@ -752,21 +751,21 @@ typedef	struct s_GeInit {
 #define SKERR_HWI_E014		(SKERR_HWI_E013+1)
 #define SKERR_HWI_E014MSG	"SkGeInitPort(): unknown GIPortUsage specified"
 #define SKERR_HWI_E015		(SKERR_HWI_E014+1)
-#define SKERR_HWI_E015MSG	"Invalid Link mode parameter"
+#define SKERR_HWI_E015MSG	"Illegal Link mode parameter"
 #define SKERR_HWI_E016		(SKERR_HWI_E015+1)
-#define SKERR_HWI_E016MSG	"Invalid Flow control mode parameter"
+#define SKERR_HWI_E016MSG	"Illegal Flow control mode parameter"
 #define SKERR_HWI_E017		(SKERR_HWI_E016+1)
-#define SKERR_HWI_E017MSG	"Invalid value specified for GIPollTimerVal"
+#define SKERR_HWI_E017MSG	"Illegal value specified for GIPollTimerVal"
 #define SKERR_HWI_E018		(SKERR_HWI_E017+1)
 #define SKERR_HWI_E018MSG	"FATAL: SkGeStopPort() does not terminate (Tx)"
 #define SKERR_HWI_E019		(SKERR_HWI_E018+1)
-#define SKERR_HWI_E019MSG	"Invalid Speed parameter"
+#define SKERR_HWI_E019MSG	"Illegal Speed parameter"
 #define SKERR_HWI_E020		(SKERR_HWI_E019+1)
-#define SKERR_HWI_E020MSG	"Invalid Master/Slave parameter"
+#define SKERR_HWI_E020MSG	"Illegal Master/Slave parameter"
 #define SKERR_HWI_E021		(SKERR_HWI_E020+1)
 #define	SKERR_HWI_E021MSG	"MacUpdateStats(): cannot update statistic counter"
 #define	SKERR_HWI_E022		(SKERR_HWI_E021+1)
-#define	SKERR_HWI_E022MSG	"MacStatistic(): invalid statistic base address"
+#define	SKERR_HWI_E022MSG	"MacStatistic(): illegal statistic base address"
 #define SKERR_HWI_E023		(SKERR_HWI_E022+1)
 #define SKERR_HWI_E023MSG	"SkGeInitPort(): Transmit Queue Size too small"
 #define SKERR_HWI_E024		(SKERR_HWI_E023+1)

drivers/net/sk98lin/h/sktypes.h

@@ -2,8 +2,8 @@
  *
  * Name:	sktypes.h
  * Project:	GEnesis, PCI Gigabit Ethernet Adapter
- * Version:	$Revision: 1.3 $
- * Date:	$Date: 2003/02/25 14:16:40 $
+ * Version:	$Revision: 1.1 $
+ * Date:	$Date: 2003/07/21 07:26:01 $
  * Purpose:	Define data types for Linux
  *
  ******************************************************************************/
@@ -26,6 +26,9 @@
  * History:
  *
  *	$Log: sktypes.h,v $
+ *	Revision 1.1  2003/07/21 07:26:01  rroesler
+ *	Fix: Re-Enter after CVS crash
+ *	
  *	Revision 1.3  2003/02/25 14:16:40  mlindner
  *	Fix: Copyright statement
  *	

drivers/net/sk98lin/h/skversion.h

@@ -2,8 +2,8 @@
  *
  * Name:	version.h
  * Project:	GEnesis, PCI Gigabit Ethernet Adapter
- * Version:	$Revision: 1.4 $
- * Date:	$Date: 2003/02/25 14:16:40 $
+ * Version:	$Revision: 1.3 $
+ * Date:	$Date: 2003/08/25 13:34:48 $
  * Purpose:	SK specific Error log support
  *
  ******************************************************************************/
@@ -25,6 +25,15 @@
  *
  * History:
  *	$Log: skversion.h,v $
+ *	Revision 1.3  2003/08/25 13:34:48  mlindner
+ *	Fix: Lint changes
+ *	
+ *	Revision 1.2  2003/08/13 12:01:01  mlindner
+ *	Add: Changes for Lint
+ *	
+ *	Revision 1.1  2003/07/24 09:29:56  rroesler
+ *	Fix: Re-Enter after CVS crash
+ *	
  *	Revision 1.4  2003/02/25 14:16:40  mlindner
  *	Fix: Copyright statement
  *	
@@ -42,13 +51,15 @@
  ******************************************************************************/
  
  
+#ifdef	lint
 static const char SysKonnectFileId[] = "@(#) (C) SysKonnect GmbH.";
 static const char SysKonnectBuildNumber[] =
-	"@(#)SK-BUILD: 6.14 PL: 01"; 
+	"@(#)SK-BUILD: 6.18 PL: 01"; 
+#endif	/* !defined(lint) */
 
-#define BOOT_STRING	"sk98lin: Network Device Driver v6.14\n" \
+#define BOOT_STRING	"sk98lin: Network Device Driver v6.18\n" \
 			"(C)Copyright 1999-2003 Marvell(R)."
 
-#define VER_STRING	"6.14"
+#define VER_STRING	"6.18"
 
 

drivers/net/sk98lin/skdim.c

@@ -2,8 +2,8 @@
  *
  * Name:	skdim.c
  * Project:	GEnesis, PCI Gigabit Ethernet Adapter
- * Version:	$Revision: 1.4 $
- * Date:	$Date: 2003/07/07 09:45:47 $
+ * Version:	$Revision: 1.2 $
+ * Date:	$Date: 2003/08/21 12:35:05 $
  * Purpose:	All functions to maintain interrupt moderation
  *
  ******************************************************************************/
@@ -26,6 +26,12 @@
  * History:
  *	
  *	$Log: skdim.c,v $
+ *	Revision 1.2  2003/08/21 12:35:05  mlindner
+ *	Fix: Corrected CPU detection and compile errors on single CPU machines
+ *	
+ *	Revision 1.1  2003/07/18 13:39:55  rroesler
+ *	Fix: Re-enter after CVS crash
+ *	
  *	Revision 1.4  2003/07/07 09:45:47  rroesler
  *	Fix: Compiler warnings corrected
  *	
@@ -56,7 +62,7 @@
 
 #ifndef	lint
 static const char SysKonnectFileId[] =
-	"@(#) $Id: skdim.c,v 1.4 2003/07/07 09:45:47 rroesler Exp $ (C) SysKonnect.";
+	"@(#) $Id: skdim.c,v 1.2 2003/08/21 12:35:05 mlindner Exp $ (C) SysKonnect.";
 #endif
 
 #define __SKADDR_C
@@ -312,6 +318,12 @@ GetCurrentSystemLoad(SK_AC *pAC) {
 	unsigned int  TotalTime   = 0;
 	unsigned int  UsedTime    = 0;
 	unsigned int  SystemLoad  = 0;
+#ifdef CONFIG_SMP
+	unsigned int  SKNumCpus   = smp_num_cpus;
+#else
+	unsigned int  SKNumCpus   = 1;
+#endif
+
 	/* unsigned int  NbrCpu      = 0; */
 
 	/*

drivers/net/tlan.c

@@ -883,7 +883,9 @@ static int TLan_Init( struct net_device *dev )
 			err );
 	}
 	dev->addr_len = 6;
-	
+
+	netif_carrier_off(dev);
+
 	/* Device methods */
 	dev->open = &TLan_Open;
 	dev->hard_start_xmit = &TLan_StartTx;
@@ -2205,6 +2207,8 @@ TLan_ResetAdapter( struct net_device *dev )
 
 	priv->tlanFullDuplex = FALSE;
 	priv->phyOnline=0;
+	netif_carrier_off(dev);
+
 /*  1.	Assert reset bit. */
 
 	data = inl(dev->base_addr + TLAN_HOST_CMD);
@@ -2368,6 +2372,7 @@ TLan_FinishReset( struct net_device *dev )
 		}
 		outl( priv->rxListDMA, dev->base_addr + TLAN_CH_PARM );
 		outl( TLAN_HC_GO | TLAN_HC_RT, dev->base_addr + TLAN_HOST_CMD );
+		netif_carrier_on(dev);
 	} else {
 		printk( "TLAN: %s: Link inactive, will retry in 10 secs...\n", dev->name );
 		TLan_SetTimer( dev, (10*HZ), TLAN_TIMER_FINISH_RESET );

drivers/net/tulip/Kconfig

@@ -23,11 +23,9 @@ config DE2104X
 	  will say Y here.) Do read the Ethernet-HOWTO, available from
 	  <http://www.tldp.org/docs.html#howto>.
 
-	  This driver is also available as a module ( = code which can be
-	  inserted in and removed from the running kernel whenever you want).
-	  The module will be called de2104x.  If you want to compile it as a
-	  module, say M here and read <file:Documentation/modules.txt> as well
-	  as <file:Documentation/networking/net-modules.txt>.
+	  To compile this driver as a module, choose M here and read
+	  <file:Documentation/networking/net-modules.txt>.  The module will
+	  be called de2104x.
 
 config TULIP
 	tristate "DECchip Tulip (dc2114x) PCI support"
@@ -44,11 +42,9 @@ config TULIP
 	  information is contained in 
 	  <file:Documentation/networking/tulip.txt>.
 
-	  This driver is also available as a module ( = code which can be
-	  inserted in and removed from the running kernel whenever you want).
-	  The module will be called tulip.  If you want to compile it as a
-	  module, say M here and read <file:Documentation/modules.txt> as well
-	  as <file:Documentation/networking/net-modules.txt>.
+	  To compile this driver as a module, choose M here and read
+	  <file:Documentation/networking/net-modules.txt>.  The module will
+	  be called tulip.
 
 config TULIP_MWI
 	bool "New bus configuration (EXPERIMENTAL)"
@@ -82,11 +78,9 @@ config DE4X5
 	  information is contained in
 	  <file:Documentation/networking/de4x5.txt>.
 
-	  This driver is also available as a module ( = code which can be
-	  inserted in and removed from the running kernel whenever you want).
-	  The module will be called de4x5.  If you want to compile it as a
-	  module, say M here and read <file:Documentation/modules.txt> as well
-	  as <file:Documentation/networking/net-modules.txt>.
+	  To compile this driver as a module, choose M here and read
+	  <file:Documentation/networking/net-modules.txt>.  The module will
+	  be called de4x5.
 
 config WINBOND_840
 	tristate "Winbond W89c840 Ethernet support"
@@ -106,11 +100,9 @@ config DM9102
 	  (Ethernet) card, say Y.  Some information is contained in the file
 	  <file:Documentation/networking/dmfe.txt>.
 
-	  This driver is also available as a module ( = code which can be
-	  inserted in and removed from the running kernel whenever you want).
-	  The module will be called dmfe.  If you want to compile it as a
-	  module, say M here and read <file:Documentation/modules.txt> as well
-	  as <file:Documentation/networking/net-modules.txt>.
+	  To compile this driver as a module, choose M here and read
+	  <file:Documentation/networking/net-modules.txt>.  The module will
+	  be called dmfe.
 
 config PCMCIA_XIRCOM
 	tristate "Xircom CardBus support (new driver)"
@@ -121,11 +113,9 @@ config PCMCIA_XIRCOM
 	  as with work-alike chips from Lite-On (PNIC) and Macronix (MXIC) and
 	  ASIX.
 
-	  This driver is also available as a module ( = code which can be
-	  inserted in and removed from the running kernel whenever you want).
-	  The module will be called xircom_cb.  If you want to compile
-	  it as a module, say M here and read
-	  <file:Documentation/modules.txt>. If unsure, say N.
+	  To compile this driver as a module, choose M here and read
+	  <file:Documentation/networking/net-modules.txt>.  The module will
+	  be called xircom_cb.  If unsure, say N.
 
 config PCMCIA_XIRTULIP
 	tristate "Xircom Tulip-like CardBus support (old driver)"
@@ -136,11 +126,9 @@ config PCMCIA_XIRTULIP
 	  as with work-alike chips from Lite-On (PNIC) and Macronix (MXIC) and
 	  ASIX.
 
-	  This driver is also available as a module ( = code which can be
-	  inserted in and removed from the running kernel whenever you want).
-	  The module will be called xircom_tulip_cb.  If you want to compile
-	  it as a module, say M here and read
-	  <file:Documentation/modules.txt>. If unsure, say N.
+	  To compile this driver as a module, choose M here and read
+	  <file:Documentation/networking/net-modules.txt>.  The module will
+	  be called xircom_tulip_cb.  If unsure, say N.
 
 endmenu
 

drivers/net/wireless/Makefile

@@ -3,7 +3,9 @@
 #
 
 obj-$(CONFIG_STRIP) += strip.o
-obj-$(CONFIG_ARLAN) += arlan.o arlan-proc.o
+obj-$(CONFIG_ARLAN) += arlan.o 
+
+arlan-objs := arlan-main.o arlan-proc.o
 
 # Obsolete cards
 obj-$(CONFIG_WAVELAN)		+= wavelan.o

drivers/net/wireless/arlan-proc.c

@@ -108,7 +108,7 @@ static const char *arlan_diagnostic_info_string(struct net_device *dev)
 		default:
 			return "ERROR unknown Diagnostic info reply code ";
 	  }
-};
+}
 
 static const char *arlan_hardware_type_string(struct net_device *dev)
 {
@@ -866,7 +866,6 @@ static int arlan_sysctl_reset(ctl_table * ctl, int write, struct file *filp,
 	CTBLN(32,cardNo,lParameter),\
 	CTBLN(33,cardNo,_15),\
 	CTBLN(34,cardNo,headerSize),\
-	CTBLN(35,cardNo,async),\
 	CTBLN(36,cardNo,tx_delay_ms),\
 	CTBLN(37,cardNo,retries),\
 	CTBLN(38,cardNo,ReTransmitPacketMaxSize),\
@@ -1233,7 +1232,7 @@ static ctl_table arlan_root_table[] =
 
 static struct ctl_table_header *arlan_device_sysctl_header;
 
-int init_arlan_proc(void)
+int __init init_arlan_proc(void)
 {
 
 	int i = 0;
@@ -1247,25 +1246,11 @@ int init_arlan_proc(void)
 
 	return 0;
 
-};
-
-
-
-#ifdef MODULE
-
-int init_module(void)
-{
-
-	return init_arlan_proc();
-};
+}
 
-void cleanup_module(void)
+void __exit cleanup_arlan_proc(void)
 {
 	unregister_sysctl_table(arlan_device_sysctl_header);
 	arlan_device_sysctl_header = NULL;
 
-	return;
-};
-
-#endif				// MODULE
-MODULE_LICENSE("GPL");
+}

drivers/net/wireless/arlan.h

@@ -39,14 +39,16 @@
 #define ARLAN_RCV_PROMISC 1
 #define ARLAN_RCV_CONTROL 2
 
-
 #ifdef CONFIG_PROC_FS
-extern int 	init_arlan_proc(void);
+extern int init_arlan_proc(void);
+extern void cleanup_arlan_proc(void);
+#else
+#define init_arlan_proc()	(0)
+#define cleanup_arlan_proc()	do { } while (0);
 #endif
 
 extern struct net_device *arlan_device[MAX_ARLANS];
 extern int	arlan_debug;
-extern char *	siteName;
 extern int	arlan_entry_debug;
 extern int	arlan_exit_debug;
 extern int	testMemory;
@@ -67,8 +69,6 @@ extern int     arlan_command(struct net_device * dev, int command);
 #define channelSetUNKNOWN 0
 #define systemIdUNKNOWN -1
 #define registrationModeUNKNOWN -1
-#define siteNameUNKNOWN "LinuxSite"
-
 
 
 #define IFDEBUG( L ) if ( (L) & arlan_debug ) 
@@ -293,7 +293,6 @@ struct arlan_conf_stru {
       int	lParameter;
       int	_15;
       int	headerSize;
-      int async;
       int retries;
       int tx_delay_ms;
       int waitReTransmitPacketMaxSize;
@@ -332,83 +331,56 @@ struct TxParam
       volatile	unsigned	char scrambled;
 };
 
-struct TxRingPoint  {
-	struct TxParam txParam;
-	
-	
-};
-
 #define TX_RING_SIZE 2
 /* Information that need to be kept for each board. */
 struct arlan_private {
       struct net_device_stats stats;
-      long open_time;			/* Useless example local info. */
       struct arlan_shmem * card;
       struct arlan_shmem * conf;
-      struct TxParam txParam;      
-      int multicastLength;
-      char  multicastList[ARLAN_MAX_MULTICAST_ADDRS][6];
-      int promiscModeEnabled;
+
       struct arlan_conf_stru * Conf;	     
       int	bad;
       int 	reset;
-      long long lastReset;
+      unsigned long lastReset;
       struct timer_list timer;
       struct timer_list tx_delay_timer;
       struct timer_list tx_retry_timer;
       struct timer_list rx_check_timer;
-      struct semaphore card_lock;
-      atomic_t 	card_users;
-      atomic_t	delay_on;
-      atomic_t  retr_on;
+
       int registrationLostCount;
       int reRegisterExp;
-      int nof_tx;
-      int nof_tx_ack;
-      int last_nof_tx;
-      int last_nof_tx_ack;
       int irq_test_done;
-      int last_command_was_rx;
+
       struct TxParam txRing[TX_RING_SIZE];
       char reTransmitBuff[0x800];
-      volatile int txLast;
-      volatile int txNew;
-      volatile int txOffset;
-      volatile char ReTransmitRequested;
-      volatile unsigned long tx_done_delayed;
-      volatile long long registrationLastSeen;
-      volatile char under_command;
-      volatile char under_toggle;
-      volatile long long tx_last_sent;
-      volatile long long tx_last_cleared;
-      volatile u_char under_tx;
-      volatile int 	retransmissions;
-      volatile int	tx_chain_active;
-      volatile int 	timer_chain_active;
-      volatile int 	interrupt_ack_requested;
-      volatile long	command_lock;
-      volatile int	rx_command_needed;
-      volatile int	tx_command_needed;
-      volatile int 	waiting_command_mask;
-      volatile int 	card_polling_interval;
-      volatile int 	last_command_buff_free_time;
-      volatile int	numResets;
-      volatile int 	under_reset;
-      volatile int 	under_config;
-      volatile int 	rx_command_given;
-      volatile long 	tx_command_given;
-      volatile long	interrupt_processing_active;
-      volatile long long 	last_tx_time;
-      volatile long long	last_rx_time;
-      volatile long long	last_rx_int_ack_time;
-      int	in_bytes;
-      int	out_bytes;
-      int	in_time;
-      int	out_time;
-      int	in_time10;
-      int	out_time10;
-      int	in_bytes10;
-      int	out_bytes10;
+      int txLast;
+      unsigned ReTransmitRequested;
+      unsigned long tx_done_delayed;
+      unsigned long registrationLastSeen;
+
+      unsigned long	tx_last_sent;
+      unsigned long	tx_last_cleared;
+      unsigned long	retransmissions;
+      unsigned long 	interrupt_ack_requested;
+      spinlock_t	lock;
+      unsigned long	waiting_command_mask;
+      unsigned long 	card_polling_interval;
+      unsigned long 	last_command_buff_free_time;
+
+      int 		under_reset;
+      int 		under_config;
+      int 		rx_command_given;
+      int	 	tx_command_given;
+      unsigned  long	interrupt_processing_active;
+      unsigned long	last_rx_int_ack_time;
+      unsigned long	in_bytes;
+      unsigned long 	out_bytes;
+      unsigned long	in_time;
+      unsigned long	out_time;
+      unsigned long	in_time10;
+      unsigned long	out_time10;
+      unsigned long	in_bytes10;
+      unsigned long 	out_bytes10;
       int	init_etherdev_alloc;
 };
 
@@ -497,13 +469,11 @@ struct arlan_private {
 #define arlan_interrupt_lancpu(dev) {\
    int cr;   \
    \
-   priv->under_toggle++;   \
    cr = readControlRegister(dev);\
    if (cr & ARLAN_CHANNEL_ATTENTION){ \
       writeControlRegister(dev, (cr & ~ARLAN_CHANNEL_ATTENTION));\
    }else  \
       writeControlRegister(dev, (cr | ARLAN_CHANNEL_ATTENTION));\
-   priv->under_toggle=0;     \
 }
 
 #define clearChannelAttention(dev){ \