Commit 4e17e1db authored by Rodolfo Giometti's avatar Rodolfo Giometti Committed by Linus Torvalds

Add c2 port support

C2port implements a two wire serial communication protocol (bit
banging) designed to enable in-system programming, debugging, and
boundary-scan testing on low pin-count Silicon Labs devices.

Currently this code supports only flash programming through sysfs
interface but extensions shoud be easy to add.
Signed-off-by: default avatarRodolfo Giometti <giometti@linux.it>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: default avatarAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: default avatarLinus Torvalds <torvalds@linux-foundation.org>
parent e0a29382
What: /sys/class/c2port/
Date: October 2008
Contact: Rodolfo Giometti <giometti@linux.it>
Description:
The /sys/class/c2port/ directory will contain files and
directories that will provide a unified interface to
the C2 port interface.
What: /sys/class/c2port/c2portX
Date: October 2008
Contact: Rodolfo Giometti <giometti@linux.it>
Description:
The /sys/class/c2port/c2portX/ directory is related to X-th
C2 port into the system. Each directory will contain files to
manage and control its C2 port.
What: /sys/class/c2port/c2portX/access
Date: October 2008
Contact: Rodolfo Giometti <giometti@linux.it>
Description:
The /sys/class/c2port/c2portX/access file enable the access
to the C2 port from the system. No commands can be sent
till this entry is set to 0.
What: /sys/class/c2port/c2portX/dev_id
Date: October 2008
Contact: Rodolfo Giometti <giometti@linux.it>
Description:
The /sys/class/c2port/c2portX/dev_id file show the device ID
of the connected micro.
What: /sys/class/c2port/c2portX/flash_access
Date: October 2008
Contact: Rodolfo Giometti <giometti@linux.it>
Description:
The /sys/class/c2port/c2portX/flash_access file enable the
access to the on-board flash of the connected micro.
No commands can be sent till this entry is set to 0.
What: /sys/class/c2port/c2portX/flash_block_size
Date: October 2008
Contact: Rodolfo Giometti <giometti@linux.it>
Description:
The /sys/class/c2port/c2portX/flash_block_size file show
the on-board flash block size of the connected micro.
What: /sys/class/c2port/c2portX/flash_blocks_num
Date: October 2008
Contact: Rodolfo Giometti <giometti@linux.it>
Description:
The /sys/class/c2port/c2portX/flash_blocks_num file show
the on-board flash blocks number of the connected micro.
What: /sys/class/c2port/c2portX/flash_data
Date: October 2008
Contact: Rodolfo Giometti <giometti@linux.it>
Description:
The /sys/class/c2port/c2portX/flash_data file export
the content of the on-board flash of the connected micro.
What: /sys/class/c2port/c2portX/flash_erase
Date: October 2008
Contact: Rodolfo Giometti <giometti@linux.it>
Description:
The /sys/class/c2port/c2portX/flash_erase file execute
the "erase" command on the on-board flash of the connected
micro.
What: /sys/class/c2port/c2portX/flash_erase
Date: October 2008
Contact: Rodolfo Giometti <giometti@linux.it>
Description:
The /sys/class/c2port/c2portX/flash_erase file show the
on-board flash size of the connected micro.
What: /sys/class/c2port/c2portX/reset
Date: October 2008
Contact: Rodolfo Giometti <giometti@linux.it>
Description:
The /sys/class/c2port/c2portX/reset file execute a "reset"
command on the connected micro.
What: /sys/class/c2port/c2portX/rev_id
Date: October 2008
Contact: Rodolfo Giometti <giometti@linux.it>
Description:
The /sys/class/c2port/c2portX/rev_id file show the revision ID
of the connected micro.
C2 port support
---------------
(C) Copyright 2007 Rodolfo Giometti <giometti@enneenne.com>
This program is free software; you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation; either version 2 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
Overview
--------
This driver implements the support for Linux of Silicon Labs (Silabs)
C2 Interface used for in-system programming of micro controllers.
By using this driver you can reprogram the in-system flash without EC2
or EC3 debug adapter. This solution is also useful in those systems
where the micro controller is connected via special GPIOs pins.
References
----------
The C2 Interface main references are at (http://www.silabs.com)
Silicon Laboratories site], see:
- AN127: FLASH Programming via the C2 Interface at
http://www.silabs.com/public/documents/tpub_doc/anote/Microcontrollers/Small_Form_Factor/en/an127.pdf, and
- C2 Specification at
http://www.silabs.com/public/documents/tpub_doc/spec/Microcontrollers/en/C2spec.pdf,
however it implements a two wire serial communication protocol (bit
banging) designed to enable in-system programming, debugging, and
boundary-scan testing on low pin-count Silicon Labs devices. Currently
this code supports only flash programming but extensions are easy to
add.
Using the driver
----------------
Once the driver is loaded you can use sysfs support to get C2port's
info or read/write in-system flash.
# ls /sys/class/c2port/c2port0/
access flash_block_size flash_erase rev_id
dev_id flash_blocks_num flash_size subsystem/
flash_access flash_data reset uevent
Initially the C2port access is disabled since you hardware may have
such lines multiplexed with other devices so, to get access to the
C2port, you need the command:
# echo 1 > /sys/class/c2port/c2port0/access
after that you should read the device ID and revision ID of the
connected micro controller:
# cat /sys/class/c2port/c2port0/dev_id
8
# cat /sys/class/c2port/c2port0/rev_id
1
However, for security reasons, the in-system flash access in not
enabled yet, to do so you need the command:
# echo 1 > /sys/class/c2port/c2port0/flash_access
After that you can read the whole flash:
# cat /sys/class/c2port/c2port0/flash_data > image
erase it:
# echo 1 > /sys/class/c2port/c2port0/flash_erase
and write it:
# cat image > /sys/class/c2port/c2port0/flash_data
after writing you have to reset the device to execute the new code:
# echo 1 > /sys/class/c2port/c2port0/reset
...@@ -498,4 +498,6 @@ config SGI_GRU_DEBUG ...@@ -498,4 +498,6 @@ config SGI_GRU_DEBUG
This option enables addition debugging code for the SGI GRU driver. If This option enables addition debugging code for the SGI GRU driver. If
you are unsure, say N. you are unsure, say N.
source "drivers/misc/c2port/Kconfig"
endif # MISC_DEVICES endif # MISC_DEVICES
...@@ -32,3 +32,4 @@ obj-$(CONFIG_KGDB_TESTS) += kgdbts.o ...@@ -32,3 +32,4 @@ obj-$(CONFIG_KGDB_TESTS) += kgdbts.o
obj-$(CONFIG_SGI_XP) += sgi-xp/ obj-$(CONFIG_SGI_XP) += sgi-xp/
obj-$(CONFIG_SGI_GRU) += sgi-gru/ obj-$(CONFIG_SGI_GRU) += sgi-gru/
obj-$(CONFIG_HP_ILO) += hpilo.o obj-$(CONFIG_HP_ILO) += hpilo.o
obj-$(CONFIG_C2PORT) += c2port/
#
# C2 port devices
#
menuconfig C2PORT
tristate "Silicon Labs C2 port support (EXPERIMENTAL)"
depends on EXPERIMENTAL
default no
help
This option enables support for Silicon Labs C2 port used to
program Silicon micro controller chips (and other 8051 compatible).
If your board have no such micro controllers you don't need this
interface at all.
To compile this driver as a module, choose M here: the module will
be called c2port_core. Note that you also need a client module
usually called c2port-*.
If you are not sure, say N here.
if C2PORT
endif # C2PORT
obj-$(CONFIG_C2PORT) += core.o
This diff is collapsed.
/*
* Silicon Labs C2 port Linux support
*
* Copyright (c) 2007 Rodolfo Giometti <giometti@linux.it>
* Copyright (c) 2007 Eurotech S.p.A. <info@eurotech.it>
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License version 2 as published by
* the Free Software Foundation
*/
#include <linux/device.h>
#define C2PORT_NAME_LEN 32
/*
* C2 port basic structs
*/
/* Main struct */
struct c2port_ops;
struct c2port_device {
unsigned int access:1;
unsigned int flash_access:1;
int id;
char name[C2PORT_NAME_LEN];
struct c2port_ops *ops;
struct mutex mutex; /* prevent races during read/write */
struct device *dev;
void *private_data;
};
/* Basic operations */
struct c2port_ops {
/* Flash layout */
unsigned short block_size; /* flash block size in bytes */
unsigned short blocks_num; /* flash blocks number */
/* Enable or disable the access to C2 port */
void (*access)(struct c2port_device *dev, int status);
/* Set C2D data line as input/output */
void (*c2d_dir)(struct c2port_device *dev, int dir);
/* Read/write C2D data line */
int (*c2d_get)(struct c2port_device *dev);
void (*c2d_set)(struct c2port_device *dev, int status);
/* Write C2CK clock line */
void (*c2ck_set)(struct c2port_device *dev, int status);
};
/*
* Exported functions
*/
#define to_class_dev(obj) container_of((obj), struct class_device, kobj)
#define to_c2port_device(obj) container_of((obj), struct c2port_device, class)
extern struct c2port_device *c2port_device_register(char *name,
struct c2port_ops *ops, void *devdata);
extern void c2port_device_unregister(struct c2port_device *dev);
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment