Merge branch 'omap-for-v4.15/fixes-dt' into omap-for-v4.16/dt

Documentation/devicetree/bindings/usb/am33xx-usb.txt

@@ -95,6 +95,7 @@ usb: usb@47400000 {
 		reg = <0x47401300 0x100>;
 		reg-names = "phy";
 		ti,ctrl_mod = <&ctrl_mod>;
+		#phy-cells = <0>;
 	};
 
 	usb0: usb@47401000 {
@@ -141,6 +142,7 @@ usb: usb@47400000 {
 		reg = <0x47401b00 0x100>;
 		reg-names = "phy";
 		ti,ctrl_mod = <&ctrl_mod>;
+		#phy-cells = <0>;
 	};
 
 	usb1: usb@47401800 {

arch/arm/boot/dts/am33xx.dtsi

@@ -630,6 +630,7 @@ usb0_phy: usb-phy@47401300 {
 				reg-names = "phy";
 				status = "disabled";
 				ti,ctrl_mod = <&usb_ctrl_mod>;
+				#phy-cells = <0>;
 			};
 
 			usb0: usb@47401000 {
@@ -678,6 +679,7 @@ usb1_phy: usb-phy@47401b00 {
 				reg-names = "phy";
 				status = "disabled";
 				ti,ctrl_mod = <&usb_ctrl_mod>;
+				#phy-cells = <0>;
 			};
 
 			usb1: usb@47401800 {

arch/arm/boot/dts/am4372.dtsi

@@ -927,7 +927,8 @@ mcasp0: mcasp@48038000 {
 			reg = <0x48038000 0x2000>,
 			      <0x46000000 0x400000>;
 			reg-names = "mpu", "dat";
-			interrupts = <80>, <81>;
+			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "tx", "rx";
 			status = "disabled";
 			dmas = <&edma 8 2>,
@@ -941,7 +942,8 @@ mcasp1: mcasp@4803C000 {
 			reg = <0x4803C000 0x2000>,
 			      <0x46400000 0x400000>;
 			reg-names = "mpu", "dat";
-			interrupts = <82>, <83>;
+			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "tx", "rx";
 			status = "disabled";
 			dmas = <&edma 10 2>,

arch/arm/boot/dts/am437x-cm-t43.dts

@@ -301,8 +301,8 @@ &spi0 {
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&spi0_pins>;
-	dmas = <&edma 16
-		&edma 17>;
+	dmas = <&edma 16 0
+		&edma 17 0>;
 	dma-names = "tx0", "rx0";
 
 	flash: w25q64cvzpig@0 {

arch/arm/boot/dts/dm814x.dtsi

@@ -75,6 +75,7 @@ usb0_phy: usb-phy@47401300 {
 				reg = <0x47401300 0x100>;
 				reg-names = "phy";
 				ti,ctrl_mod = <&usb_ctrl_mod>;
+				#phy-cells = <0>;
 			};
 
 			usb0: usb@47401000 {

arch/arm/boot/dts/logicpd-som-lv-37xx-devkit.dts

@@ -72,7 +72,8 @@ &charger {
 };
 
 &gpmc {
-	ranges = <1 0 0x08000000 0x1000000>;	/* CS1: 16MB for LAN9221 */
+	ranges = <0 0 0x30000000 0x1000000	/* CS0: 16MB for NAND */
+		  1 0 0x2c000000 0x1000000>;	/* CS1: 16MB for LAN9221 */
 
 	ethernet@gpmc {
 		pinctrl-names = "default";

arch/arm/boot/dts/logicpd-som-lv.dtsi

@@ -33,11 +33,12 @@ wl12xx_vmmc: wl12xx_vmmc {
 	hsusb2_phy: hsusb2_phy {
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; /* gpio_4 */
+		#phy-cells = <0>;
 	};
 };
 
 &gpmc {
-	ranges = <0 0 0x00000000 0x1000000>;	/* CS0: 16MB for NAND */
+	ranges = <0 0 0x30000000 0x1000000>;	/* CS0: 16MB for NAND */
 
 	nand@0,0 {
 		compatible = "ti,omap2-nand";
@@ -94,7 +95,7 @@ &i2c3 {
 
 &mmc3 {
 	interrupts-extended = <&intc 94 &omap3_pmx_core2 0x46>;
-	pinctrl-0 = <&mmc3_pins>;
+	pinctrl-0 = <&mmc3_pins &wl127x_gpio>;
 	pinctrl-names = "default";
 	vmmc-supply = <&wl12xx_vmmc>;
 	non-removable;
@@ -105,8 +106,8 @@ &mmc3 {
 	wlcore: wlcore@2 {
 		compatible = "ti,wl1273";
 		reg = <2>;
-		interrupt-parent = <&gpio5>;
-		interrupts = <24 IRQ_TYPE_LEVEL_HIGH>; /* gpio 152 */
+		interrupt-parent = <&gpio1>;
+		interrupts = <2 IRQ_TYPE_LEVEL_HIGH>; /* gpio 2 */
 		ref-clock-frequency = <26000000>;
 	};
 };
@@ -130,8 +131,6 @@ OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE3)	/* sdmmc2_dat4.sdmmc3_da
 			OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE3)	/* sdmmc2_dat5.sdmmc3_dat1 */
 			OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE3)	/* sdmmc2_dat6.sdmmc3_dat2 */
 			OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE3)	/* sdmmc2_dat6.sdmmc3_dat3 */
-			OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP | MUX_MODE4)	/* mcbsp4_clkx.gpio_152 */
-			OMAP3_CORE1_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE4)	/* sys_boot1.gpio_3 */
 			OMAP3_CORE1_IOPAD(0x21d0, PIN_INPUT_PULLUP | MUX_MODE3) /* mcspi1_cs1.sdmmc3_cmd */
 			OMAP3_CORE1_IOPAD(0x21d2, PIN_INPUT_PULLUP | MUX_MODE3)	/* mcspi1_cs2.sdmmc_clk */
 		>;
@@ -201,6 +200,12 @@ hsusb2_reset_pin: pinmux_hsusb1_reset_pin {
 			OMAP3_WKUP_IOPAD(0x2a0e, PIN_OUTPUT | MUX_MODE4)	/* sys_boot2.gpio_4 */
 		>;
 	};
+	wl127x_gpio: pinmux_wl127x_gpio_pin {
+		pinctrl-single,pins = <
+			OMAP3_WKUP_IOPAD(0x2a0c, PIN_INPUT | MUX_MODE4)		/* sys_boot0.gpio_2 */
+			OMAP3_WKUP_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE4)	/* sys_boot1.gpio_3 */
+		>;
+	};
 };
 
 &omap3_pmx_core2 {

arch/arm/boot/dts/omap3-beagle-xm.dts

@@ -90,6 +90,7 @@ hsusb2_phy: hsusb2_phy {
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio5 19 GPIO_ACTIVE_LOW>; /* gpio_147 */
 		vcc-supply = <&hsusb2_power>;
+		#phy-cells = <0>;
 	};
 
 	tfp410: encoder0 {

arch/arm/boot/dts/omap3-beagle.dts

@@ -64,6 +64,7 @@ hsusb2_phy: hsusb2_phy {
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio5 19 GPIO_ACTIVE_LOW>;	/* gpio_147 */
 		vcc-supply = <&hsusb2_power>;
+		#phy-cells = <0>;
 	};
 
 	sound {

arch/arm/boot/dts/omap3-cm-t3x.dtsi

@@ -43,12 +43,14 @@ hsusb2_power: hsusb2_power_reg {
 	hsusb1_phy: hsusb1_phy {
 		compatible = "usb-nop-xceiv";
 		vcc-supply = <&hsusb1_power>;
+		#phy-cells = <0>;
 	};
 
 	/* HS USB Host PHY on PORT 2 */
 	hsusb2_phy: hsusb2_phy {
 		compatible = "usb-nop-xceiv";
 		vcc-supply = <&hsusb2_power>;
+		#phy-cells = <0>;
 	};
 
 	ads7846reg: ads7846-reg {

arch/arm/boot/dts/omap3-evm-common.dtsi

@@ -29,6 +29,7 @@ hsusb2_phy: hsusb2_phy {
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio1 21 GPIO_ACTIVE_LOW>; /* gpio_21 */
 		vcc-supply = <&hsusb2_power>;
+		#phy-cells = <0>;
 	};
 
 	leds {

arch/arm/boot/dts/omap3-gta04.dtsi

@@ -120,6 +120,7 @@ pwm11: dmtimer-pwm {
 	hsusb2_phy: hsusb2_phy {
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio6 14 GPIO_ACTIVE_LOW>;
+		#phy-cells = <0>;
 	};
 
 	tv0: connector {

arch/arm/boot/dts/omap3-igep0020-common.dtsi

@@ -58,6 +58,7 @@ hsusb1_phy: hsusb1_phy {
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio1 24 GPIO_ACTIVE_LOW>; /* gpio_24 */
 		vcc-supply = <&hsusb1_power>;
+		#phy-cells = <0>;
 	};
 
 	tfp410: encoder {

arch/arm/boot/dts/omap3-igep0030-common.dtsi

@@ -37,6 +37,7 @@ user2 {
 	hsusb2_phy: hsusb2_phy {
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio2 22 GPIO_ACTIVE_LOW>;		/* gpio_54 */
+		#phy-cells = <0>;
 	};
 };
 

arch/arm/boot/dts/omap3-lilly-a83x.dtsi

@@ -51,6 +51,7 @@ reg_vcc3: vcc3 {
 	hsusb1_phy: hsusb1_phy {
 		compatible = "usb-nop-xceiv";
 		vcc-supply = <&reg_vcc3>;
+		#phy-cells = <0>;
 	};
 };
 

arch/arm/boot/dts/omap3-overo-base.dtsi

@@ -51,6 +51,7 @@ hsusb2_phy: hsusb2_phy {
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio6 23 GPIO_ACTIVE_LOW>;	/* gpio_183 */
 		vcc-supply = <&hsusb2_power>;
+		#phy-cells = <0>;
 	};
 
 	/* Regulator to trigger the nPoweron signal of the Wifi module */

arch/arm/boot/dts/omap3-pandora-common.dtsi

@@ -205,6 +205,7 @@ hsusb2_phy: hsusb2_phy {
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio1 16 GPIO_ACTIVE_LOW>; /* GPIO_16 */
 		vcc-supply = <&vaux2>;
+		#phy-cells = <0>;
 	};
 
 	/* HS USB Host VBUS supply

arch/arm/boot/dts/omap3-tao3530.dtsi

@@ -46,6 +46,7 @@ hsusb2_phy: hsusb2_phy {
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio6 2 GPIO_ACTIVE_LOW>;	/* gpio_162 */
 		vcc-supply = <&hsusb2_power>;
+		#phy-cells = <0>;
 	};
 
 	sound {

arch/arm/boot/dts/omap3.dtsi

@@ -715,6 +715,7 @@ usbhsohci: ohci@48064400 {
 				compatible = "ti,ohci-omap3";
 				reg = <0x48064400 0x400>;
 				interrupts = <76>;
+				remote-wakeup-connected;
 			};
 
 			usbhsehci: ehci@48064800 {

arch/arm/boot/dts/omap4-droid4-xt894.dts

@@ -73,6 +73,7 @@ hdmi_regulator: regulator-hdmi {
 	/* HS USB Host PHY on PORT 1 */
 	hsusb1_phy: hsusb1_phy {
 		compatible = "usb-nop-xceiv";
+		#phy-cells = <0>;
 	};
 
 	/* LCD regulator from sw5 source */

arch/arm/boot/dts/omap4-duovero.dtsi

@@ -43,6 +43,7 @@ sound {
 	hsusb1_phy: hsusb1_phy {
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>;	/* gpio_62 */
+		#phy-cells = <0>;
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&hsusb1phy_pins>;

arch/arm/boot/dts/omap4-panda-common.dtsi

@@ -89,6 +89,7 @@ hsusb1_power: hsusb1_power_reg {
 	hsusb1_phy: hsusb1_phy {
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>;   /* gpio_62 */
+		#phy-cells = <0>;
 		vcc-supply = <&hsusb1_power>;
 		clocks = <&auxclk3_ck>;
 		clock-names = "main_clk";

arch/arm/boot/dts/omap4-var-som-om44.dtsi

@@ -44,6 +44,7 @@ &hsusbb1_phy_rst_pins
 
 		reset-gpios = <&gpio6 17 GPIO_ACTIVE_LOW>; /* gpio 177 */
 		vcc-supply = <&vbat>;
+		#phy-cells = <0>;
 
 		clocks = <&auxclk3_ck>;
 		clock-names = "main_clk";

arch/arm/boot/dts/omap4.dtsi

@@ -1081,14 +1081,13 @@ usbhshost: usbhshost@4a064000 {
 			usbhsohci: ohci@4a064800 {
 				compatible = "ti,ohci-omap3";
 				reg = <0x4a064800 0x400>;
-				interrupt-parent = <&gic>;
 				interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+				remote-wakeup-connected;
 			};
 
 			usbhsehci: ehci@4a064c00 {
 				compatible = "ti,ehci-omap";
 				reg = <0x4a064c00 0x400>;
-				interrupt-parent = <&gic>;
 				interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
 			};
 		};

arch/arm/boot/dts/omap5-board-common.dtsi

@@ -73,12 +73,14 @@ hsusb2_phy: hsusb2_phy {
 		clocks = <&auxclk1_ck>;
 		clock-names = "main_clk";
 		clock-frequency = <19200000>;
+		#phy-cells = <0>;
 	};
 
 	/* HS USB Host PHY on PORT 3 */
 	hsusb3_phy: hsusb3_phy {
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>; /* gpio3_79 ETH_NRESET */
+		#phy-cells = <0>;
 	};
 
 	tpd12s015: encoder {

arch/arm/boot/dts/omap5-cm-t54.dts

@@ -63,12 +63,14 @@ ads7846reg: ads7846-reg {
 	hsusb2_phy: hsusb2_phy {
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>; /* gpio3_76 HUB_RESET */
+		#phy-cells = <0>;
 	};
 
 	/* HS USB Host PHY on PORT 3 */
 	hsusb3_phy: hsusb3_phy {
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>; /* gpio3_83 ETH_RESET */
+		#phy-cells = <0>;
 	};
 
 	leds {

arch/arm/boot/dts/omap5.dtsi

@@ -940,6 +940,7 @@ usbhsohci: ohci@4a064800 {
 				compatible = "ti,ohci-omap3";
 				reg = <0x4a064800 0x400>;
 				interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+				remote-wakeup-connected;
 			};
 
 			usbhsehci: ehci@4a064c00 {