V4L/DVB (8236): cx23885: add support for new revision of FusionHDTV7 Dual Express

The new revision of this board uses the same pci subsystem id as the first
revision, but uses a S5H1411 demodulator instead of the S5H1409.

In the case of the FusionHDTV7 Dual Express,
if s5h1409_attach fails, try s5h1411_attach.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

drivers/media/video/cx23885/Kconfig

@@ -14,6 +14,7 @@ config VIDEO_CX23885
 	select DVB_DIB7000P if !DVB_FE_CUSTOMISE
 	select MEDIA_TUNER_MT2131 if !DVB_FE_CUSTOMISE
 	select DVB_S5H1409 if !DVB_FE_CUSTOMISE
+	select DVB_S5H1411 if !DVB_FE_CUSTOMISE
 	select DVB_LGDT330X if !DVB_FE_CUSTOMISE
 	select MEDIA_TUNER_XC2028 if !DVB_FE_CUSTOMIZE
 	select MEDIA_TUNER_TDA8290 if !DVB_FE_CUSTOMIZE

drivers/media/video/cx23885/cx23885-dvb.c

@@ -31,6 +31,7 @@
 #include <media/v4l2-common.h>
 
 #include "s5h1409.h"
+#include "s5h1411.h"
 #include "mt2131.h"
 #include "tda8290.h"
 #include "tda18271.h"
@@ -174,6 +175,16 @@ static struct s5h1409_config dvico_s5h1409_config = {
 	.mpeg_timing   = S5H1409_MPEGTIMING_CONTINOUS_NONINVERTING_CLOCK,
 };
 
+static struct s5h1411_config dvico_s5h1411_config = {
+	.output_mode   = S5H1411_SERIAL_OUTPUT,
+	.gpio          = S5H1411_GPIO_ON,
+	.qam_if        = S5H1411_IF_44000,
+	.vsb_if        = S5H1411_IF_44000,
+	.inversion     = S5H1411_INVERSION_OFF,
+	.status_mode   = S5H1411_DEMODLOCKING,
+	.mpeg_timing   = S5H1411_MPEGTIMING_CONTINOUS_NONINVERTING_CLOCK,
+};
+
 static struct xc5000_config hauppauge_hvr1500q_tunerconfig = {
 	.i2c_address      = 0x61,
 	.if_khz           = 5380,
@@ -475,6 +486,10 @@ static int dvb_register(struct cx23885_tsport *port)
 		port->dvb.frontend = dvb_attach(s5h1409_attach,
 						&dvico_s5h1409_config,
 						&i2c_bus->i2c_adap);
+		if (port->dvb.frontend == NULL)
+			port->dvb.frontend = dvb_attach(s5h1411_attach,
+							&dvico_s5h1411_config,
+							&i2c_bus->i2c_adap);
 		if (port->dvb.frontend != NULL)
 			dvb_attach(xc5000_attach, port->dvb.frontend,
 				&i2c_bus->i2c_adap,