Commit 542ae60a authored by Dongpo Li's avatar Dongpo Li Committed by David S. Miller

net: hisilicon: Add Fast Ethernet MAC driver

This patch adds the Hisilicon Fast Ethernet MAC(FEMAC) driver.
The FEMAC supports max speed 100Mbps and has been used in many
Hisilicon SoC.
Signed-off-by: default avatarDongpo Li <lidongpo@hisilicon.com>
Reviewed-by: default avatarJiancheng Xue <xuejiancheng@hisilicon.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent b7862412
Hisilicon Fast Ethernet MAC controller
Required properties:
- compatible: should contain one of the following version strings:
* "hisilicon,hisi-femac-v1"
* "hisilicon,hisi-femac-v2"
and the soc string "hisilicon,hi3516cv300-femac".
- reg: specifies base physical address(s) and size of the device registers.
The first region is the MAC core register base and size.
The second region is the global MAC control register.
- interrupts: should contain the MAC interrupt.
- clocks: A phandle to the MAC main clock.
- resets: should contain the phandle to the MAC reset signal(required) and
the PHY reset signal(optional).
- reset-names: should contain the reset signal name "mac"(required)
and "phy"(optional).
- mac-address: see ethernet.txt [1].
- phy-mode: see ethernet.txt [1].
- phy-handle: see ethernet.txt [1].
- hisilicon,phy-reset-delays-us: triplet of delays if PHY reset signal given.
The 1st cell is reset pre-delay in micro seconds.
The 2nd cell is reset pulse in micro seconds.
The 3rd cell is reset post-delay in micro seconds.
[1] Documentation/devicetree/bindings/net/ethernet.txt
Example:
hisi_femac: ethernet@10090000 {
compatible = "hisilicon,hi3516cv300-femac","hisilicon,hisi-femac-v2";
reg = <0x10090000 0x1000>,<0x10091300 0x200>;
interrupts = <12>;
clocks = <&crg HI3518EV200_ETH_CLK>;
resets = <&crg 0xec 0>,<&crg 0xec 3>;
reset-names = "mac","phy";
mac-address = [00 00 00 00 00 00];
phy-mode = "mii";
phy-handle = <&phy0>;
hisilicon,phy-reset-delays-us = <10000 20000 20000>;
};
......@@ -23,6 +23,18 @@ config HIX5HD2_GMAC
help
This selects the hix5hd2 mac family network device.
config HISI_FEMAC
tristate "Hisilicon Fast Ethernet MAC device support"
depends on HAS_IOMEM
select PHYLIB
select RESET_CONTROLLER
help
This selects the Hisilicon Fast Ethernet MAC device(FEMAC).
The FEMAC receives and transmits data over Ethernet
ports at 10/100 Mbps in full-duplex or half-duplex mode.
The FEMAC exchanges data with the CPU, and supports
the energy efficient Ethernet (EEE).
config HIP04_ETH
tristate "HISILICON P04 Ethernet support"
depends on HAS_IOMEM # For MFD_SYSCON
......
......@@ -6,3 +6,4 @@ obj-$(CONFIG_HIX5HD2_GMAC) += hix5hd2_gmac.o
obj-$(CONFIG_HIP04_ETH) += hip04_eth.o
obj-$(CONFIG_HNS_MDIO) += hns_mdio.o
obj-$(CONFIG_HNS) += hns/
obj-$(CONFIG_HISI_FEMAC) += hisi_femac.o
This diff is collapsed.
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment