ARM: dts: stm32: Add Ethernet support on stm32h7 SOC and activate it for eval and disco boards

Synopsys GMAC 4.10 is used. And Phy mode for eval and disco is RMII
with PHY SMSC LAN8742
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

arch/arm/boot/dts/stm32h743-pinctrl.dtsi

@@ -173,6 +173,21 @@ pins {
 				};
 			};
 
+			ethernet_rmii: rmii@0 {
+				pins {
+					pinmux = <STM32_PINMUX('G', 11, AF11)>,
+						 <STM32_PINMUX('G', 13, AF11)>,
+						 <STM32_PINMUX('G', 12, AF11)>,
+						 <STM32_PINMUX('C', 4, AF11)>,
+						 <STM32_PINMUX('C', 5, AF11)>,
+						 <STM32_PINMUX('A', 7, AF11)>,
+						 <STM32_PINMUX('C', 1, AF11)>,
+						 <STM32_PINMUX('A', 2, AF11)>,
+						 <STM32_PINMUX('A', 1, AF11)>;
+					slew-rate = <2>;
+				};
+			};
+
 			usart1_pins: usart1@0 {
 				pins1 {
 					pinmux = <STM32_PINMUX('B', 14, AF4)>; /* USART1_TX */

arch/arm/boot/dts/stm32h743.dtsi

@@ -511,6 +511,19 @@ adc3: adc@0 {
 				status = "disabled";
 			};
 		};
+
+		mac: ethernet@40028000 {
+			compatible = "st,stm32-dwmac", "snps,dwmac-4.10a";
+			reg = <0x40028000 0x8000>;
+			reg-names = "stmmaceth";
+			interrupts = <61>;
+			interrupt-names = "macirq";
+			clock-names = "stmmaceth", "mac-clk-tx", "mac-clk-rx";
+			clocks = <&rcc ETH1MAC_CK>, <&rcc ETH1TX_CK>, <&rcc ETH1RX_CK>;
+			st,syscon = <&syscfg 0x4>;
+			snps,pbl = <8>;
+			status = "disabled";
+		};
 	};
 };
 

arch/arm/boot/dts/stm32h743i-disco.dts

@@ -66,6 +66,23 @@ &clk_hse {
 	clock-frequency = <25000000>;
 };
 
+&mac {
+	status = "disabled";
+	pinctrl-0	= <&ethernet_rmii>;
+	pinctrl-names	= "default";
+	phy-mode	= "rmii";
+	phy-handle	= <&phy0>;
+
+	mdio0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		phy0: ethernet-phy@0 {
+			reg = <0>;
+		};
+	};
+};
+
 &usart2 {
 	pinctrl-0 = <&usart2_pins>;
 	pinctrl-names = "default";

arch/arm/boot/dts/stm32h743i-eval.dts

@@ -104,6 +104,23 @@ &rtc {
 	status = "okay";
 };
 
+&mac {
+	status = "disabled";
+	pinctrl-0	= <&ethernet_rmii>;
+	pinctrl-names	= "default";
+	phy-mode	= "rmii";
+	phy-handle	= <&phy0>;
+
+	mdio0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		phy0: ethernet-phy@0 {
+			reg = <0>;
+		};
+	};
+};
+
 &usart1 {
 	pinctrl-0 = <&usart1_pins>;
 	pinctrl-names = "default";